Home › Engine / Hybrid System › 1UR-FE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049093 1UR-FE ENGINE CONTROL _0233909 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0128  Thermostat  


DESCRIPTION

This DTC is stored when the Engine Coolant Temperature (ECT) does not reach 75°C (167°F) despite sufficient engine warm-up time having elapsed.

DTC No. DTC Detection Condition Trouble Area
P0128

Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic):

(a) Cold start

(b) Engine warmed up

(c) ECT less than 75°C (167°F)


·

Water inlet with thermostat sub-assembly

·

Cooling system

·

ECT sensor

·

ECM



MONITOR DESCRIPTION

A121605E02
3.74,2.207 3.257,1.244 false 4.861,2.289 5.155,2.639 false 4.455,2.647 5.937,2.830 1.482,0.183 10 Indicated ECT Reading 3.197,3.67 5.202,3.877 2.004,0.208 10 DTC Set (after 2 Driving Cycles) 2.246,1.141 3.239,1.364 0.993,0.223 10 Estimated ECT 0.812,1.564 1.756,1.939 0.944,0.374 10 Threshold (75°C (167°F)) 4.281,1.012 4.971,1.178 0.690,0.166 10 5 seconds 1.78,2.817 2.100,3.021 0.320,0.204 10 ECT 2.288,3.296 2.627,3.508 0.339,0.212 10 Time

The ECM estimates the ECT based on the starting temperature, engine loads, and engine speeds. The ECM then compares the estimated temperature with the actual ECT. When the estimated ECT reaches 75°C (167°F), the ECM checks the actual ECT. If the actual ECT is less than 75°C (167°F), the ECM interprets this as a malfunction in the thermostat or the engine cooling system and stores the DTC.

MONITOR STRATEGY

Related DTCs P0128: Coolant Thermostat
Required Sensors/Components (Main) Thermostat
Required Sensors/Components (Related) Engine Coolant Temperature (ECT) sensor, Intake Air Temperature (IAT) sensor, Vehicle speed sensor
Frequency of Operation Once per driving cycle
Duration 920 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P006A, P0107, P0108 (Manifold absolute pressure)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0401 (EGR system)
P0500 (Vehicle speed sensor)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
Battery voltage 11 V or more
Either of following conditions 1 or 2 met: -
1. All of following conditions met: -
·

ECT at engine start - IAT at engine start


-15 to 7°C (-5 to 44.6°F)
·

ECT at engine start


-10 to 56°C (14 to 133°F)
·

IAT at engine start


-10 to 56°C (14 to 133°F)
2. All of following conditions met: -
·

ECT at engine start - IAT at engine start


More than 7°C (44.6°F)
·

ECT at engine start


56°C (133°F) or less
·

IAT at engine start


-10°C (14°F) or more
Accumulated time at vehicle speed of 128 km/h (80 mph) or more Less than 20 seconds

TYPICAL MALFUNCTION THRESHOLDS

Duration that both of following conditions (a) and (b) met 5 seconds or more
(a) Estimated ECT 75°C (167°F) or more
(b) ECT sensor output Below 75°C (167°F)

CONFIRMATION DRIVING PATTERN

A198821E54
0.168,1.174 1.296,1.351 1.128,0.177 10 80 km/h (50 mph) 0.358,1.579 1.275,1.924 0.917,0.345 10 Ignition Switch ON 1.768,1.45 1.994,1.609 0.226,0.159 10 [A] 3.29,1.076 3.483,1.269 0.193,0.193 10 [B] 4.803,2.921 5.033,3.151 0.230,0.230 10 [C] 3.043,2.253 3.742,2.437 0.700,0.184 10 15 minutes 2.47,0.024 6.476,0.180 4.006,0.156 10 - Engine coolant temperature when engine started: 56°C or less 2.47,0.349 6.058,0.494 3.587,0.144 10 - Intake air temperature when engine started: 0 to 35°C 2.47,0.663 6.571,0.819 4.101,0.156 10 - Heater set to MAX HOT with fresh air mode selected and A/C off

1.

Stop the engine and allow it to soak.

2.

Connect the Techstream to the DLC3.

3.

Turn the ignition switch to ON and turn the Techstream on [A].

4.

Enter the following menu items: Powertrain / Engine and ECT / Data List / Coolant Temp and Intake Air.

5.

Check that "Coolant Temp" is 56°C (133°F) or less and "Intake Air" is between 0 and 35°C (0 and 95°F).

6.

Set the heater to MAX HOT with fresh air mode selected and turn the A/C off.

7.

Start the engine and drive the vehicle at 80 km/h (50 mph) for 15 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Data can be captured relatively easily by using the snapshot function in the Data List.

·

Enter the following menu: Data List / Function / Snap-shot configuration / Record time / 5 min.

·

Data capture can be started by using the target point function. For example, setting the target point to an engine speed of 4000 rpm and then racing the engine, etc. to raise the engine speed to a speed of 4000 rpm or more will cause data capture to start.



8.

After "Coolant Temp" stabilizes, check that "Coolant Temp" is 75°C (167°F) or higher [C].

HINT:

If "Coolant Temp" is below 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and thermostat.



CAUTION / NOTICE / HINT

HINT:
·

When the DTC is output, check the engine coolant temperature using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp. If the Coolant Temp value is lower than the actual engine coolant temperature, the engine coolant temperature sensor circuit may be malfunctioning. In this case, check the wire harnesses and connectors (and those connections) between the ECM and the engine coolant temperature sensor first.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0128)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0128 is output A
P0128 and other DTCs are output B

HINT:

If any DTCs other than P0128 are output, troubleshoot those DTCs first.




A

2.CHECK COOLING SYSTEM

B

2.CHECK COOLING SYSTEM
a.

Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



OK

3.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

NG

REPAIR OR REPLACE COOLING SYSTEM

3.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Remove the water inlet with thermostat sub-assembly (See page Engine / Hybrid System>1UR-FE COOLING>THERMOSTAT>REMOVAL).


b.

Measure the valve opening temperature of the thermostat.

Standard opening temperature:

80 to 84°C (176 to 183°F)


HINT:

In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.




OK

4.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

4.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).



OK

NG