Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  P0305  Cylinder 5 Misfire Detected  P0306  Cylinder 6 Misfire Detected  P0307  Cylinder 7 Misfire Detected  P0308  Cylinder 8 Misfire Detected  


DESCRIPTION

A093767E16
2.302,0.906 2.708,1.073 0.406,0.167 10 false ECM 0.427,0.927 1.292,1.125 0.865,0.198 10 false CMP Sensor 0.427,1.729 1.292,1.917 0.865,0.188 10 false CKP Sensor

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high HC concentration levels can cause increases in exhaust emission levels. High concentrations of HC can also cause increases in the Three-Way Catalytic Converter (TWC) temperature, which may cause damage to the TWC. To prevent these increases in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the TWC reaches the point of thermal degradation, the MIL blinks. To monitor misfires, the ECM uses both the Camshaft Position (CMP) sensor and the Crankshaft Position (CKP) sensor. The CMP sensor is used to identify any misfiring cylinders and the CKP sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted as when the crankshaft rotation speed variations exceed predetermined thresholds.

If the misfire rate exceeds the threshold level, the ECM illuminates the MIL and sets a DTC.

DTC Code DTC Detection Condition Trouble Area
P0300 Simultaneous misfiring of several cylinders occurs and one of the following conditions below is detected (2 trip detection logic):
·

Misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

Catalyst deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Injector

·

Fuel pressure

·

Mass Air Flow (MAF) meter

·

Engine Coolant Temperature (ECT) sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Air induction system

·

ECM


P0301
P0302
P0303
P0304
P0305
P0306
P0307
P0308
Misfiring of specific cylinder occurs and one of the following conditions below is detected (2 trip detection logic):
·

Misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

Catalyst deterioration misfire occurs (MIL illuminates).



When multiple DTCs for misfiring cylinders are set, but DTC P0300 is not set, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only set when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

·

Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs once.

·

An excessive misfiring rate (approximately 10 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and sets a DTC (2 trip detection logic) when either one of the following conditions, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected:

·

At a high engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs once.

·

At a normal engine rpm, a catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.


HINT:

If a catalyst damage misfire occurs, the ECM informs the driver by flashing the MIL.


Misfire Monitor for Mexico Models

The ECM illuminates the MIL and sets a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).

·

Within the first 1000 crankshaft revolutions of the engine starting, an excessive misfiring rate (approximately 1000 misfires per 1000 crankshaft revolutions) occurs once.

·

An excessive misfiring rate (approximately 500 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL and sets a DTC when the following condition, which could cause the Three-Way Catalytic Converter (TWC) damage, is detected (2 trip detection logic).

·

A catalyst damage misfire, which monitored every 200 crankshaft revolutions, occurs 3 times.



MONITOR STRATEGY

Related DTCs P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
P0307: Cylinder 7 misfire
P0308: Cylinder 8 misfire
Required Sensors/Components (Main) Crankshaft position sensor and Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature and intake air temperature sensors and Mass air flow meter
Frequency of Operation Continuous
Duration 1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emissions-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
MIL Operation 2 driving cycles: MIL illuminates when misfire detect
MIL flashes immediately: When catalyst damaged misfire occur
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Misfire:
Monitor runs whenever following DTCs not present P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (Knock Sensor)
P0335 (Crankshaft position sensor)
P0340, P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle speed sensor)
Battery voltage 8 V or more
VVT system Not operated by scan tool
Engine RPM 400 to 5900 rpm
Either of following conditions (a) or (b) met -
(a) ECT at engine start More than -7°C (19°F)
(b) ECT More than 20°C (68°F)
Fuel cut OFF

Monitor period of emission-related-misfire:
First 1000 revolutions after engine start, or Check Mode Crankshaft 1000 revolutions
Except above Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged-misfire (MIL blinks):
All of following conditions 1, 2, 3 and 4 met Crankshaft 200 revolutions x 3
1. Driving cycles 1st
2. Check mode OFF
3. Engine RPM Less than 2800 rpm
4. Engine load Less than 80%
Except above Crankshaft 200 revolutions

FOR MEXICO MODELS:

Misfire: for Mexico models
Monitor runs whenever following DTCs not present P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle speed sensor)
Battery voltage 8 V or more
VVT system Not operated by scan tool
Engine RPM 450 to 4500 rpm
ECT More than 65°C (149°F)
Fuel cut OFF

Monitor period of emission-related-misfire: for Mexico models
First 1000 revolutions after engine start, or Check Mode Crankshaft 1000 revolutions
Except above Crankshaft 1000 revolutions x 4

Monitor period of catalyst-damaged-misfire (MIL blinks): for Mexico models
All of following conditions 1 and 2 met Crankshaft 200 revolutions x 3
1. Driving cycles 1st
2. Check mode OFF
Except above Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS

Monitor period of emission-related-misfire:
Misfire rate 1.5% or more

Monitor period of catalyst-damaged-misfire (MIL blinks):
Number of misfire per 200 revolutions 103 or more (varies with intake air amount and RPM)

FOR MEXICO MODELS:

Monitor period of emission-related-misfire: for Mexico models
Misfire rate 25% or more: for 1st 1000 revolutions
12.5% or more: after 1st 1000 revolutions

Monitor period of catalyst-damaged-misfire (MIL blinks): for Mexico models
Number of misfire per 200 revolutions 103 or more (varies with intake air amount and RPM)
Paired cylinder misfire (MIL blinks immediately) Detected

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the Techstream on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

6.

Using the tester, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>CHECK MODE PROCEDURE).

7.

Read the misfire counts of each cylinder (Cylinder #1 Misfire Count to Cylinder #8 Misfire Count) with the engine in an idling condition.

8.

Drive the vehicle several times with the conditions, such as engine rpm and engine load, shown in Misfire RPM and Misfire Load in the Data List.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below with the engine speed and engine load the same as Misfire RPM and Misfire Load in the freeze frame data.

Engine RPM Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minute or more


9.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTCs, freeze frame data and other data will be cleared.


10.

Record the DTC(s), freeze frame data and misfire counts.

11.

Turn the ignition switch off and wait for at least 15 seconds.

12.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).


WIRING DIAGRAM

A164725E02
5.11,0.272 5.391,0.428 0.281,0.156 10 #10 5.11,0.958 5.391,1.114 0.281,0.156 10 #20 5.11,1.645 5.391,1.801 0.281,0.156 10 #30 5.11,2.335 5.391,2.491 0.281,0.156 10 #40 5.11,3.026 5.391,3.182 0.281,0.156 10 #50 5.11,3.716 5.391,3.872 0.281,0.156 10 #60 5.11,4.415 5.391,4.571 0.281,0.156 10 #70 5.11,5.133 5.391,5.289 0.281,0.156 10 #80 5.101,5.734 5.405,5.890 0.304,0.156 10 E01 5.101,6.084 5.405,6.240 0.304,0.156 10 E02 5.845,6.559 6.197,6.715 0.351,0.156 10 ECM 5.845,6.414 6.132,6.584 0.286,0.169 10 D74 4.862,6.071 5.045,6.220 0.184,0.150 10 42 4.862,5.72 5.045,5.870 0.184,0.150 10 43 4.778,5.12 5.045,5.269 0.267,0.149 10 106 4.778,3.712 5.045,3.861 0.267,0.149 10 107 4.865,4.406 5.045,4.558 0.180,0.152 10 83 4.865,3.013 5.045,3.165 0.180,0.152 10 84 4.792,2.326 5.045,2.475 0.253,0.149 10 108 4.862,1.64 5.045,1.789 0.184,0.149 10 85 4.778,0.946 5.045,1.095 0.267,0.149 10 109 4.869,0.26 5.045,0.402 0.177,0.142 10 86 3.784,0.268 3.895,0.421 0.111,0.152 10 2 3.784,0.957 3.895,1.109 0.111,0.152 10 2 3.784,1.645 3.895,1.797 0.111,0.152 10 2 3.784,2.333 3.895,2.485 0.111,0.152 10 2 3.784,3.021 3.895,3.174 0.111,0.152 10 2 3.784,3.71 3.895,3.862 0.111,0.152 10 2 3.784,4.398 3.895,4.550 0.111,0.152 10 2 3.784,5.122 3.895,5.274 0.111,0.152 10 2 4.404,0.273 4.518,0.429 0.114,0.156 10 1 0.532,1.368 0.647,1.524 0.114,0.156 10 1 4.404,0.96 4.518,1.116 0.114,0.156 10 1 4.404,1.646 4.518,1.802 0.114,0.156 10 1 4.404,2.333 4.518,2.489 0.114,0.156 10 1 4.404,3.019 4.518,3.175 0.114,0.156 10 1 4.404,3.706 4.518,3.862 0.114,0.156 10 1 4.404,4.392 4.518,4.548 0.114,0.156 10 1 4.408,5.126 4.522,5.282 0.114,0.156 10 1 3.663,0.569 4.527,0.746 0.864,0.177 10 No. 1 Injector 3.663,0.429 3.937,0.580 0.274,0.151 10 H1 3.663,1.802 3.937,1.953 0.274,0.151 10 H2 3.663,3.185 3.937,3.335 0.274,0.151 10 H3 3.663,4.576 3.937,4.727 0.274,0.151 10 H4 3.663,1.256 4.527,1.433 0.864,0.177 10 No. 2 Injector 3.663,1.116 3.961,1.266 0.298,0.151 10 F1 3.663,2.498 3.961,2.649 0.298,0.151 10 F2 3.663,3.881 3.961,4.031 0.298,0.150 10 F3 3.663,5.3 3.961,5.451 0.298,0.150 10 F4 3.663,1.943 4.527,2.119 0.864,0.177 10 No. 3 Injector 3.663,2.629 4.527,2.806 0.864,0.177 10 No. 4 Injector 3.663,3.323 4.527,3.500 0.864,0.177 10 No. 5 Injector 3.663,4.022 4.527,4.199 0.864,0.177 10 No. 6 Injector 3.663,4.712 4.527,4.889 0.864,0.177 10 No. 7 Injector 3.663,5.432 4.527,5.608 0.864,0.177 10 No. 8 Injector 2.917,0.475 3.170,0.638 0.253,0.163 10 INJ 1.566,0.909 1.847,1.065 0.282,0.156 10 IG2 0.424,0.505 1.086,0.666 0.662,0.161 10 IG2 MAIN 2.34,0.609 2.554,0.779 0.214,0.170 10 1B 2.34,0.343 2.554,0.513 0.214,0.170 10 1B 1.083,1.369 1.297,1.539 0.214,0.170 10 1B 0.266,1.369 0.480,1.539 0.214,0.170 10 1C 2.395,0.201 2.496,0.343 0.100,0.142 10 8 2.395,0.775 2.496,0.917 0.100,0.142 10 7 1.353,1.372 1.484,1.514 0.132,0.142 10 6 1.232,1.743 1.364,1.885 0.132,0.142 10 6 1.232,2.677 1.364,2.819 0.132,0.142 10 5 1.643,1.526 2.771,1.709 1.128,0.184 10 Integration Relay 1.257,1.958 1.534,2.123 0.276,0.165 10 IG2 1.239,2.425 1.571,2.590 0.332,0.165 10 AM2 1.687,2.263 2.648,2.465 0.961,0.202 10 Ignition Switch 1.687,2.116 1.880,2.291 0.193,0.174 10 J9 1.264,3.237 1.596,3.421 0.332,0.184 10 AM2 1.425,5.738 1.900,5.922 0.474,0.184 10 Battery

A259910E01
5.377,0.841 5.713,1.011 0.336,0.170 10 IGT1 3.471,0.911 3.808,1.081 0.336,0.170 10 IGT1 5.377,2.508 5.713,2.678 0.336,0.170 10 IGT3 5.377,4.176 5.713,4.346 0.336,0.170 10 IGT5 5.377,5.843 5.713,6.013 0.336,0.170 10 IGT7 5.378,1.25 5.709,1.419 0.331,0.169 10 IGF1 3.473,1.32 3.804,1.489 0.331,0.169 10 IGF1 5.911,6.458 6.206,6.614 0.295,0.156 10 D74 5.121,0.841 5.305,0.997 0.184,0.156 10 40 5.121,2.508 5.305,2.664 0.184,0.156 10 37 5.121,4.176 5.305,4.332 0.184,0.156 10 35 5.121,5.843 5.305,5.999 0.184,0.156 10 38 5.037,1.25 5.304,1.406 0.267,0.156 10 104 5.902,6.612 6.266,6.796 0.364,0.184 10 ECM 3.853,0.831 3.968,0.987 0.114,0.156 10 3 3.856,1.228 3.991,1.391 0.135,0.163 10 2 2.891,0.835 2.991,0.991 0.100,0.156 10 1 2.897,1.227 3.011,1.383 0.114,0.156 10 4 2.813,1.58 3.107,1.736 0.295,0.156 10 D10 2.841,1.748 4.010,1.918 1.170,0.170 10 No. 1 Ignition Coil 3.051,0.909 3.262,1.063 0.211,0.154 10 +B 3.051,1.316 3.401,1.471 0.350,0.156 10 GND 3.471,2.593 3.808,2.762 0.336,0.170 10 IGT3 3.473,3.001 3.804,3.170 0.331,0.169 10 IGF2 3.853,2.512 3.968,2.668 0.114,0.156 10 3 3.856,2.909 3.991,3.072 0.135,0.163 10 2 2.891,2.502 2.991,2.658 0.100,0.156 10 1 2.897,2.909 3.011,3.065 0.114,0.156 10 4 2.813,3.261 3.107,3.417 0.295,0.156 10 D12 2.841,3.429 4.010,3.599 1.170,0.170 10 No. 3 Ignition Coil 3.051,2.59 3.262,2.744 0.211,0.154 10 +B 3.051,2.997 3.401,3.153 0.350,0.156 10 GND 3.471,4.26 3.808,4.430 0.336,0.170 10 IGT5 3.473,4.669 3.804,4.838 0.331,0.169 10 IGF2 3.853,4.18 3.968,4.335 0.114,0.156 10 3 3.856,4.576 3.991,4.739 0.135,0.163 10 2 2.891,4.184 2.991,4.340 0.100,0.156 10 1 2.897,4.576 3.011,4.732 0.114,0.156 10 4 2.813,4.928 3.107,5.084 0.295,0.156 10 D14 2.841,5.096 4.010,5.266 1.170,0.170 10 No. 5 Ignition Coil 3.051,4.258 3.262,4.411 0.211,0.154 10 +B 3.051,4.664 3.401,4.820 0.350,0.156 10 GND 3.471,5.927 3.808,6.097 0.336,0.170 10 IGT7 3.473,6.336 3.804,6.505 0.331,0.169 10 IGF1 3.853,5.847 3.968,6.003 0.114,0.156 10 3 3.856,6.244 3.991,6.407 0.135,0.163 10 2 2.891,5.837 2.991,5.993 0.100,0.156 10 1 2.897,6.243 3.011,6.399 0.114,0.156 10 4 2.813,6.595 3.107,6.751 0.295,0.156 10 D16 2.813,6.764 3.982,6.933 1.170,0.170 10 No. 7 Ignition Coil 3.051,5.925 3.262,6.079 0.211,0.154 10 +B 3.051,6.331 3.401,6.487 0.350,0.156 10 GND 1.657,0.515 1.905,0.671 0.248,0.156 10 INJ 0.139,0.118 1.119,0.302 0.980,0.184 10 from IG2 Relay 1.54,7.548 1.668,7.718 0.128,0.170 10 A 4.553,7.548 4.681,7.718 0.128,0.170 10 B 4.791,7.548 4.919,7.718 0.128,0.170 10 C

A259911E01
5.38,0.896 5.748,1.061 0.368,0.165 10 IGT2 5.38,2.559 5.748,2.724 0.368,0.165 10 IGT4 5.38,4.221 5.748,4.386 0.368,0.165 10 IGT6 5.38,5.903 5.748,6.068 0.368,0.165 10 IGT8 5.38,1.307 5.730,1.491 0.350,0.184 10 IGF2 5.945,6.661 6.240,6.826 0.295,0.165 10 D74 5.135,0.91 5.347,1.085 0.211,0.174 10 33 5.07,1.307 5.346,1.472 0.276,0.165 10 105 5.144,2.563 5.333,2.724 0.188,0.161 10 34 5.13,4.231 5.319,4.391 0.188,0.161 10 36 5.13,5.912 5.319,6.072 0.188,0.161 10 39 3.853,0.915 3.972,1.071 0.119,0.156 10 3 3.853,1.307 3.972,1.463 0.119,0.156 10 2 2.9,0.915 3.001,1.079 0.100,0.164 10 1 2.886,1.319 3.004,1.493 0.119,0.174 10 4 3.461,0.99 3.820,1.155 0.360,0.165 10 IGT2 3.078,0.999 3.298,1.155 0.221,0.156 10 +B 3.078,1.391 3.419,1.547 0.341,0.156 10 GND 3.451,1.391 3.802,1.547 0.350,0.156 10 IGF2 3.853,2.591 3.972,2.747 0.119,0.156 10 3 3.853,2.984 3.972,3.140 0.119,0.156 10 2 2.9,2.591 3.001,2.755 0.100,0.164 10 1 2.886,2.996 3.004,3.170 0.119,0.174 10 4 3.461,2.666 3.820,2.831 0.360,0.165 10 IGT4 3.078,2.675 3.298,2.831 0.221,0.156 10 +B 3.078,3.068 3.419,3.224 0.341,0.156 10 GND 3.451,3.068 3.802,3.224 0.350,0.156 10 IGF1 3.853,4.254 3.972,4.410 0.119,0.156 10 3 3.853,4.646 3.972,4.802 0.119,0.156 10 2 2.9,4.254 3.001,4.418 0.100,0.164 10 1 2.886,4.658 3.004,4.833 0.119,0.174 10 4 3.461,4.329 3.820,4.494 0.360,0.165 10 IGT6 3.078,4.338 3.298,4.494 0.221,0.156 10 +B 3.078,4.73 3.419,4.886 0.341,0.156 10 GND 3.451,4.73 3.802,4.886 0.350,0.156 10 IGF1 3.853,5.926 3.972,6.082 0.119,0.156 10 3 3.853,6.318 3.972,6.474 0.119,0.156 10 2 2.9,5.926 3.001,6.090 0.100,0.164 10 1 2.886,6.33 3.004,6.505 0.119,0.174 10 4 3.461,6.001 3.820,6.166 0.360,0.165 10 IGT8 3.078,6.01 3.298,6.166 0.221,0.156 10 +B 3.078,6.402 3.419,6.558 0.341,0.156 10 GND 3.451,6.402 3.802,6.558 0.350,0.156 10 IGF2 5.945,6.804 6.286,6.969 0.341,0.165 10 ECM 1.545,0.093 1.684,0.258 0.139,0.165 10 A 4.572,0.093 4.710,0.258 0.139,0.165 10 B 4.796,0.093 4.934,0.258 0.139,0.165 10 C 2.888,1.656 3.202,1.821 0.313,0.165 10 D25 2.888,1.805 4.035,1.989 1.147,0.184 10 No. 2 Ignition Coil 2.888,3.337 3.202,3.502 0.313,0.165 10 D23 2.888,3.487 4.035,3.670 1.147,0.184 10 No. 4 Ignition Coil 2.888,5 3.202,5.165 0.313,0.165 10 D21 2.888,5.149 4.035,5.333 1.147,0.184 10 No. 6 Ignition Coil 2.888,6.662 3.202,6.828 0.313,0.165 10 D19 2.888,6.812 4.035,6.996 1.147,0.184 10 No. 8 Ignition Coil

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the freeze frame data have been duplicated, one of the following factors is considered to be a possible cause of the problem:

1.

The fuel level is low.

2.

Improper fuel is used.

3.

The spark plugs are dirty.


·

After finishing repairs, check that no misfires occur in each cylinder (cylinder No. 1, No. 2, No. 3, No. 4, No. 5, No. 6, No. 7 and No. 8).

·

Be sure to confirm that no misfiring cylinder DTCs are set again by conducting the confirmation driving pattern, after the repairs.

·

For 6 and 8 cylinder engines, the ECM intentionally does not set the specific misfiring cylinder DTCs at high engine RPM. If misfires only occur during high engine RPM driving, only DTC P0300 is set.

In the event of DTC P0300 being present, perform the following operations:

2.

Start the engine and conduct the confirmation driving pattern.

3.

Read the misfiring rates of each cylinder or DTC(s) using the Techstream.

4.

Repair the cylinder(s) that has a high misfiring rate or is indicated by the DTC.

5.

After finishing repairs, conduct the confirmation driving pattern again, in order to verify that DTC P0300 is not set.


·

When either Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be rich (-20% or less) or lean (+20% or more).

·

When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires occurred only while warming up the engine.

·

An extremely imbalanced drive wheel can cause body vibration, which may cause misfire DTC(s) to be stored.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 are output A
P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and/or P0308 and other DTCs are output B


HINT:

If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 and P0308 are output, troubleshoot those DTCs first.



A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

OK:

PCV hose is connected correctly and is not damaged.




OK

3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)

NG

3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Misfire RPM and Misfire Load.


d.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.




NEXT

4.READ VALUE USING TECHSTREAM
4.READ VALUE USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.


d.

Read the value displayed on the Techstream.

Result
Data List Display Item Proceed to
Catalyst OT MF F/C Avail A
Not Avl B



A

5.PERFORM ACTIVE TEST USING TECHSTREAM

B

6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
5.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.


e.

Perform the Active Test.

NOTICE:

When performing the Active Test, make sure the vehicle is stopped and either idling or being revved within 3000 rpm.




NEXT

6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire / Cylinder #1 Misfire Rate, #2, #3, #4, #5, #6, #7 and #8.


b.

Allow the engine to idle.


c.

Read each value for Cylinder #1 Misfire Rate to #8 displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedures:

i.

Move the shift lever to the D position.


ii.

Check the Cylinder #1 Misfire Rate to #8.


iii.

If misfire counts are still not displayed, perform procedure "A" and "B" and then check the misfire counts again.



d.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "READ VALUE USING Techstream Misfire RPM and Misfire Load" procedures above. (Procedure "A")


e.

Read the Cylinder #1 Misfire Rate to #8 or DTCs displayed on the Techstream. (Procedure "B")

Result
Misfire Count Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B

HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data's record of the ECT is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data's record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.





A

7.INSPECT SPARK PLUG

B

17.CHECK AIR INDUCTION SYSTEM
7.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>3UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

8.CHECK FOR SPARK (SPARK TEST)

NG

8.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>3UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

9.CHECK CYLINDER COMPRESSION PRESSURE
9.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

10.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
U151414E01
0.15,0.993 0.445,1.163 0.295,0.170 10 D74 0.068,0.039 2.416,0.395 2.348,0.356 10 Front view of wire harness connector: (to ECM) 1.883,0.965 2.169,1.120 0.286,0.156 10 E01 3.056,2.533 3.323,2.688 0.267,0.156 10 #10 3.02,1.054 3.287,1.210 0.267,0.156 10 #30 2.48,0.986 2.747,1.142 0.267,0.156 10 #50 2.14,2.895 2.410,3.051 0.271,0.156 10 #60 2.39,2.648 2.675,2.804 0.286,0.156 10 #40 2.785,2.795 3.042,2.951 0.258,0.156 10 #20 3.159,2.51 2.537,1.971 false 2.636,1.158 2.342,1.977 false 3.135,1.231 2.445,1.977 false 2.239,1.725 2.033,1.146 false 2.538,2.098 2.893,2.786 false 2.445,2.098 2.554,2.64 false 2.263,2.889 2.343,2.109 false 1.839,2.655 2.106,2.811 0.267,0.156 10 #80 2.004,2.65 2.235,2.109 false 1.44,2.9 1.707,3.056 0.267,0.156 10 #70 1.625,2.885 2.249,1.952 false

a.

Disconnect the D74 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D74-86 (#10) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-109 (#20) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-85 (#30) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-108 (#40) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-84 (#50) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-107 (#60) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-83 (#70) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-106 (#80) - D74-43 (E01) Ignition switch ON 11 to 14 V




OK

11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

11.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>3UR-FE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

12.CHECK AIR INDUCTION SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

12.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

13.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

13.CHECK FUEL PRESSURE

OK

14.READ VALUE USING TECHSTREAM (COOLANT TEMP)

NG

32.CHECK FUEL LINE
14.READ VALUE USING TECHSTREAM (COOLANT TEMP)

OK

15.READ VALUE USING TECHSTREAM (MAF)

NG

15.READ VALUE USING TECHSTREAM (MAF)

OK

16.CHECK VALVE TIMING

NG

27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
16.CHECK VALVE TIMING

OK

17.CHECK AIR INDUCTION SYSTEM

NG

17.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

18.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

18.CHECK FUEL PRESSURE

OK

19.READ VALUE USING TECHSTREAM (COOLANT TEMP)

NG

CHECK FUEL LINE

19.READ VALUE USING TECHSTREAM (COOLANT TEMP)

OK

20.READ VALUE USING TECHSTREAM (MAF)

NG

20.READ VALUE USING TECHSTREAM (MAF)

OK

21.CHECK VALVE TIMING

NG

27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
22.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>3UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

23.CHECK FOR SPARK (SPARK TEST)

NG

23.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>3UR-FE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

24.CHECK CYLINDER COMPRESSION PRESSURE
24.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>3UR-FE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

25.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

25.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50, #60, #70 AND/OR #80 VOLTAGE)
U151414E01
0.15,0.993 0.445,1.163 0.295,0.170 10 D74 0.068,0.039 2.416,0.395 2.348,0.356 10 Front view of wire harness connector: (to ECM) 1.883,0.965 2.169,1.120 0.286,0.156 10 E01 3.056,2.533 3.323,2.688 0.267,0.156 10 #10 3.02,1.054 3.287,1.210 0.267,0.156 10 #30 2.48,0.986 2.747,1.142 0.267,0.156 10 #50 2.14,2.895 2.410,3.051 0.271,0.156 10 #60 2.39,2.648 2.675,2.804 0.286,0.156 10 #40 2.785,2.795 3.042,2.951 0.258,0.156 10 #20 3.159,2.51 2.537,1.971 false 2.636,1.158 2.342,1.977 false 3.135,1.231 2.445,1.977 false 2.239,1.725 2.033,1.146 false 2.538,2.098 2.893,2.786 false 2.445,2.098 2.554,2.64 false 2.263,2.889 2.343,2.109 false 1.839,2.655 2.106,2.811 0.267,0.156 10 #80 2.004,2.65 2.235,2.109 false 1.44,2.9 1.707,3.056 0.267,0.156 10 #70 1.625,2.885 2.249,1.952 false

a.

Disconnect the D74 ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D74-86 (#10) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-109 (#20) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-85 (#30) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-108 (#40) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-84 (#50) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-107 (#60) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-83 (#70) - D74-43 (E01) Ignition switch ON 11 to 14 V
D74-106 (#80) - D74-43 (E01) Ignition switch ON 11 to 14 V




OK

26.CHECK FUEL INJECTOR OF MISFIRING CYLINDER

NG

26.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
a.

Check the injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>3UR-FE FUEL>FUEL INJECTOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

NG

REPLACE FUEL INJECTOR ASSEMBLY

27.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

28.CHECK WHETHER DTC OUTPUT RECURS
28.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


m.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
A
NORMAL
(No DTC output)
B



A

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER)

B

END

29.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER)

OK

30.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the results of the inspections performed in steps 15 and 20 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
31.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the Techstream on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307 or P0308 output)
B



A

END

B

32.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

REPLACE FUEL PUMP ASSEMBLY

NG

REPAIR OR REPLACE FUEL LINE