The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0500 | While vehicle being driven, no vehicle speed sensor signal transmitted to ECM
(2 trip detection logic) |
·
Open or short in speed signal circuit ·
Wheel speed sensor ·
Combination meter ·
ECM ·
Skid control ECU |
The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and sets the DTC.
| Related DTCs | P0500: Vehicle speed sensor "A" pulse input error |
| Required Sensors/Components (Main) | Vehicle Speed Sensor (VSS), Combination meter and Skid control ECU |
| Required Sensors/Components (Related) | Park / Neutral Position (PNP) switch, Engine Coolant Temperature (ECT) sensor, Crankshaft Position (CKP) sensor, Throttle Position (TP) sensor and Mass Air Flow (MAF) meter |
| Frequency of Operation | Continuous |
| Duration | 5 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Time after ignition switch off to ON | 3 seconds or more |
| Vehicle speed | 9 km/h (5.6 mph) or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Vehicle speed sensor signal | No signal |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on [A].
Start the engine.
Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].
Stop the vehicle.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
Read the Pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0500.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.
The vehicle speed sensor is operating normally if the speedometer reading is normal.
If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).
OK
NG
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the Techstream.
Vehicle speeds displayed on Techstream and speedometer display are equal.
OK
NG
Disconnect the J28 combination meter connector.
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J28-29 (+S) - A24-13 (SPD) | Always | Below 1 Ω |
| J28-29 (+S) or A24-13 (SPD) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the J28 combination meter connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J28-29 (+S) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
OK
NG
Move the shift lever to the neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J28-29 (+S) - Body ground | ·
Ignition switch ON ·
Wheel is turned slowly |
Voltage generated intermittently |
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
OK
NG
Move the shift lever to the neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J28-30 (SI) - Body ground | ·
Ignition switch ON ·
Wheel is turned slowly |
Voltage generated intermittently |
The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.
OK
NG
Disconnect the combination meter connector.
Disconnect the brake actuator connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J28-30 (SI) - A17-3 (SP1) | Always | Below 1 Ω |
| J28-30 (SI) - or A17-3 (SP1) - Body ground | Always | 10 kΩ or higher |
OK
NG