Home › Engine / Hybrid System › 3UR-FE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049094 3UR-FE ENGINE CONTROL _0233910 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P2444  Secondary Air Injection System Pump Stuck On Bank1  P2445  Secondary Air Injection System Pump Stuck Off Bank1  P2446  Secondary Air Injection System Pump Stuck On Bank 2  P2447  Secondary Air Injection System Pump Stuck Off Bank 2  


DESCRIPTION

Refer to P2440 (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>P2440).

DTC Code DTC Detection Condition Trouble Area
P2444
P2446
Secondary air pressure more than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn off
(2 trip detection logic)
·

Short in air pump circuit

·

Open or short in pressure sensor circuit

·

Pressure sensor

·

Air Injection Control Driver (AID)

·

ECM


P2445
P2447
Secondary air pressure less than 2.4 kPa (18 mmHg) despite ECM commanding air pump to turn on
(2 trip detection logic)
·

Air pump

·

Open in air pump circuit

·

Air injection system piping

·

Vacuum hose (pressure sensor - air switching valve)

·

Pressure sensor

·

Open or short in pressure sensor circuit

·

Air Injection Control Driver (AID)

·

ECM


When secondary air injection is on, the amount of air from the air pump is below the threshold (2 trip detection logic).

MONITOR DESCRIPTION

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the Air Switching Valve (ASV) of the Secondary Air Injection (AIR) system. The sensor measures the pressure in the secondary air passage and transmits a signal to the ECM.

If either of the following conditions occurs, the ECM interprets it as a malfunction of the AIR system, and illuminates the MIL and sets a DTC:

·

The pressure indicated by the pressure sensor does not reach threshold levels despite the ECM turning on the air pump.

·

The pressure indicated by the pressure sensor exceeds threshold levels despite the ECM turning off the air pump.


MONITOR STRATEGY

Related DTCs P2444: Air pump stuck ON
P2445: Air pump stuck OFF
P2446: Air pump stuck ON
P2447: Air pump stuck OFF
Required Sensors/Components (Main) Pressure sensor
Required Sensors/Components (Related) -
Frequency of Operation Once per drive cycle
Duration 7 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

All
Monitor runs whenever following DTCs not present P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance)
P0012, P0022 (VVT system - Retard)
P0013, P0023 (Exhaust VVT oil control valve)
P0014, P0024 (Exhaust VVT system - Advance)
P0015, P0025 (Exhaust VVT system - Retard)
P0016, P0018 (VVT system - Misalignment)
P0017, P0019 (Exhaust VVT system - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0171, P0172, P0174, P0175 (Fuel system)
P0301 - P0308 (Misfire)
P0327, P0328, P032C, P032D, P0332, P0333, P033C, P033D (Knock Sensor)
P0335 (Crankshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0340, P1340 (Camshaft position sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0451, P0452, P0453 (Evaporative Emission System Pressure Sensor)
P0500 (Vehicle speed sensor)
P106B (Evap. emission control system Pressure Sensor - Air Injection System Pressure Sensor correlation)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P2431, P2432, P2433, P2435, P2436, P2437, P2438 (Secondary Air Injection System Pressure Sensor)

P2444, P2446 AIR pump is stuck ON, P2445, P2447 AIR pump is stuck OFF
Battery voltage 11 V or higher
Atmospheric pressure 45 kPa (337.5 mmHg) or more
Engine Running
AIR monitor during AIR: ON*1 Completed
AIR monitor during AIR: OFF*2 Completed
Air injection Driver (open/short or out of range) Not detected
AIR pressure sensor (open/short or out of range) Not detected

*1: AIR monitor during AIR: ON
Time after AIR in operation 5 seconds or more
AIR pump ON
AIR valve Open
Engine speed Less than 3550 rpm
Intake air amount Less than 99 gm/sec
Time after engine start 1 second or more

*2: AIR monitor during AIR: OFF
Time after AIR in operation 10 seconds or more
AIR pump OFF
AIR valve Closed
Engine speed Less than 2800 rpm
AIR monitor during AIR: ON Completed
Time after engine started 1 second or more

P2445, P2447 AIR insufficient
Battery voltage 11 V or higher
Atmospheric pressure 45 kPa (337.5 mmHg) or more
Engine Running
Air flow pattern check condition during AIR monitor during AIR: ON* Completed
AIR injection driver fail (open/short or out of range) Not detected
AIR pressure sensor fail (open/short or out of range) Not detected
*: Air flow pattern check condition during AIR monitor during AIR: ON -
AIR valve Open
Time after secondary air injection in operation 1 second or more

TYPICAL MALFUNCTION THRESHOLDS

Secondary Air Injection ON (Condition 1)
Following conditions are met during AIR ON -
Cumulative pressure pulsation 10 kPa or higher
AIR pressure 2.4 kPa or higher

Secondary Air Injection ON (Condition 2)
Following conditions are met during AIR ON -
Cumulative pressure pulsation 20 kPa or higher
AIR pressure Below 2.4 kPa

Secondary Air Injection ON (Condition 3)
Following conditions are met during AIR ON -
Cumulative pressure pulsation Below 10 kPa
AIR pressure 2.4 kPa or higher

Secondary Air Injection ON (Condition 4)
Following conditions are met during AIR ON -
Cumulative pressure pulsation Below 20 kPa
AIR pressure Below 2.4 kPa

Secondary Air Injection OFF (Condition 1)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation 30 kPa or higher
AIR pressure 2.4 kPa or higher

Secondary Air Injection OFF (Condition 2)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation 41.25 kPa or higher
AIR pressure Below 2.4 kPa

Secondary Air Injection OFF (Condition 3)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation Below 30 kPa
AIR pressure 2.4 kPa or higher

Secondary Air Injection OFF (Condition 4)
Following conditions are met during AIR OFF -
Cumulative pressure pulsation Below 41.25 kPa
AIR pressure Below 2.4 kPa

P2444, P2446 AIR pump is stuck ON
Either condition is met: (a) or (b)
(a) AIR OFF Condition 1 Met
(b) AIR OFF Condition 3 Met

P2445, P2447 AIR pump is stuck OFF
Either condition is met: (a) or (b)
(a) AIR ON Condition 2 Met
(b) AIR ON Condition 4 Met

P2445, P2447 AIR insufficient
Cumulative pressure pulsation (a) or (b)
(a) Air flow value at Bank 1 or Bank 2 140 L/min or less
(b) Air flow value at Bank 1 and Bank 2 140 L/min or less

MONITOR RESULT

CONFIRMATION DRIVING PATTERN

A199319E04
0.226,1.73 1.419,1.914 1.193,0.184 10 Ignition Switch ON 0.264,2.211 1.457,2.395 1.193,0.184 10 Ignition Switch off 2.744,1.851 2.955,2.098 0.211,0.246 10 [A] 6.166,2.901 6.369,3.103 0.202,0.202 10 [B] 4.294,2.561 5.469,2.745 1.174,0.184 10 2 minutes or more 1.006,1.209 1.447,1.428 0.441,0.218 10 Idling

NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the Techstream on.

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the Techstream on [A].

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.

10.

Start the engine after the Techstream initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the ENTER (Exit).

13.

Check pending DTCs [B].

OK:

No pending DTC is output.


14.

After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2444, P2445, P2446 or P2447.

16.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If no permanent DTC is output, the system is normal.

·

If a permanent DTC is output, the system is malfunctioning.



18.

Turn the ignition switch off.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Determination by ECM monitoring:

The ECM locates malfunctions in the Secondary Air Injection (AIR) system by detecting the pressure in the AIR passage between the air pump and Air Switching Valve (ASV) and sets a DTC. Soon after cold engine starts, the monitor runs for a short time while the AIR system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.

The following 8 patterns are AIR system pressure conditions in the AIR system passage.


Pressure Condition in Secondary Air Injection System Case 1:
Air Pump ON
Air Switching Valve Open
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2:
Air Pump OFF
Air Switching Valve Open
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3:
Air Pump ON
Air Switching Valve Closed
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4:
Air Pump OFF
Air Switching Valve Close
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5:
Air Pump ON
Air Switching Valve Open
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6:
Air Pump OFF
Air Switching Valve Open
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7:
Air Pump ON
Air Switching Valve Closed
Pressure 2.4 kPa or more
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8:
Air Pump OFF
Air Switching Valve Close
Pressure Less than 2.4 kPa
Pulsation Detection Exhaust gas pulsation not detected

If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the ASV is assumed to be open. The ECM locates malfunctions from the combination of pressures detected when the AIR system is ON and OFF.

HINT:

The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.


HINT:
·

In case 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the ASV, the average pressure is higher than in case 1 (approximately 20 to 30 kPa).

·

In case 1, the average pressure is approximately 3 to 11 kPa. The value of 2.4 kPa indicated in the table above is a threshold for detecting pump malfunctions.



Detected Conditions while AIR operating:
Air pump ON, ASV Open
Detected Conditions while AIR not operating:
Air pump OFF, ASV Closed
ECM Determination DTCs Output
Case 1 Case 8 Normal -
Case 1 Case 6 ASV stuck open P2440
or
P2442
Case 1 Case 7 Air pump stuck ON P2444
or
P2446
Case 2 Case 8 Air pump stuck OFF P2445
or
P2447
Case 3 Case 8 ASV stuck closed P2441
or
P2443
Case 1 Case 5 ASV stuck open and air pump stuck ON P2440 and P2444
or
P2442 and P2446
Case 2 Case 6 ASV stuck open and air pump stuck OFF P2440 and P2445
or
P2442 and P2447
Case 3 Case 7 ASV stuck closed and air pump stuck ON P2441 and P2444
or
P2443 and P2446
Case 4 Case 8 ASV stuck closed and air pump stuck OFF P2441 and P2445
or
P2443 and P2447

HINT:
·

If the vacuum hose between the ASV and the pressure sensor is not connected correctly, case 4 may occur.

·

By using the Techstream to perform the Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



System Check:

The pressure in the secondary air passage can be checked using the Techstream.

1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the Techstream to the DLC3.

4.

Turn the ignition switch to ON and turn the Techstream on.

5.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1 CLOSE, AIR PUMP 2: OFF, ASV2 CLOSE.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


6.

Start the engine.

7.

Perform the AIR system intrusive operation while the engine is idling.

8.

Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) displayed on the Techstream indicate the conditions shown in the table below.

Standard:
Operation AIR PUMP ASV PRESSURE*1 PULSATION*2
AIR PUMP: ON, ASV: OPEN ON OPEN 2.4 kPa or more 20 kPa or more
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Less than 2.4 kPa Less than 30 kPa


*1:

Average pumping pressure (gauge pressure). The pressure should be 2.4 kPa or more when the AIR system operates.

*2:

The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.

9.

Turn the ignition switch off.

NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.





PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2444, P2445, P2446 AND/OR P2447)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
P2444, P2445, P2446 and/or P2447 are output A
P2444, P2445, P2446 and/or P2447 and other DTCs (except P0418 and P0419) are output B
P2444, P2445, P2446 and/or P2447 and P0418 and/or P0419 are output C

If any DTCs other than P0418, P0419, P2444, P2445, P2446 and/or P2447 are output, troubleshoot those DTCs first.



A

2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMPHEATER)

B

C

GO TO AIR PUMP INSPECTION PROCEDURE

2.PERFORM ACTIVE TEST USING TECHSTREAM (ACTIVATE THE AIR PUMPHEATER)
a.
U151726E01
0.112,0.079 2.406,0.443 2.295,0.364 10 Front view of wire harness connector (to Air Pump Assembly) 0.41,1.428 0.733,1.570 0.323,0.142 10 D89 0.41,1.789 0.733,1.931 0.323,0.142 10 D90 0.816,1.359 0.983,1.505 0.166,0.145 10 *1 0.816,1.746 1.010,1.895 0.194,0.149 10 *2 0.301,2.683 1.193,2.845 0.892,0.163 10 *1: for Bank 1 0.301,3.018 1.193,3.181 0.892,0.163 10 *2: for Bank 2 0.49,0.818 0.917,0.981 0.427,0.163 10 APH+ 1.613,1.525 1.004,0.911 false

Disconnect the air pump connector.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage
Tester Connection Condition Specified Condition
D89-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V
D90-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V


f.

Reconnect the air pump connector.



OK

3.INSPECT AIR PUMP ASSEMBLY (BANK 1 OR BANK 2) (HEATER RESISTANCE)

NG

4.INSPECT AIR PUMP HEATER RELAY
3.INSPECT AIR PUMP ASSEMBLY (BANK 1 OR BANK 2) (HEATER RESISTANCE)
a.

Inspect the air pump assembly (bank 1 or bank 2) (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>AIR PUMP>ON-VEHICLE INSPECTION).



OK

4.INSPECT AIR PUMP HEATER RELAY

NG

REPLACE AIR PUMP ASSEMBLY (BANK 1 OR BANK 2)

4.INSPECT AIR PUMP HEATER RELAY

OK

5.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)

NG

5.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
a.

Remove the air pump heater relay (AI-HTR).


b.
A258729E09
0.12,0.03 1.901,0.213 1.781,0.184 10 Engine Room Relay Block: 1.586,1.432 2.212,1.657 0.626,0.225 10 AI-HTR

Measure the voltage according to the value(s) in the table below.

Standard Voltage
Tester Connection Condition Specified Condition
Air pump heater relay terminal 5 - Body ground Always 11 to 14 V


c.

Reinstall the air pump heater relay (AI-HTR).



OK

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODYGROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODYGROUND)
a.

Remove the air pump heater relay (AI-HTR).


b.

Disconnect the air pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance
Tester Connection Condition Specified Condition
AI-HTR relay terminal 3 - D89-1 (APH+) Always Below 1 Ω
AI-HTR relay terminal 3 - D90-1 (APH+) Always Below 1 Ω
D89-3 (APHG) - Body ground Always Below 1 Ω
D90-3 (APHG) - Body ground Always Below 1 Ω
AI-HTR relay terminal 3 or D89-1 (APH+) - Body ground Always 10 kΩ or higher
AI-HTR relay terminal 3 or D90-1 (APH+) - Body ground Always 10 kΩ or higher


d.

Reinstall the air pump heater relay (AI-HTR).


e.

Reconnect the air pump connector.



OK

7.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



f.

Start the engine.


g.

Perform the AIR system intrusive operation while the engine is idling.


h.

Check that the air pump (AIR PUMP), ASV and pressure in the AIR system passage (PRESSURE) status displayed on the Techstream indicate the conditions shown in the table below.

Standard:
Operation AIR PUMP ASV PRESSURE*
AIR PUMP: ON, ASV: OPEN ON OPEN 2.4 kPa or more
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Less than 2.4 kPa


*: Average pumping pressure. The pressure should be 2.4 kPa or more when the AIR system operates.


i.

Turn the ignition switch off.

NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If an ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.





OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2247)

NG

9.CHECK VACUUM HOSES (PRESSURE SENSOR - AIR SWITCHING VALVE)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2247)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.



f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Automatic Mode.


g.

Start the engine after the Techstream initialization is finished.


h.

Perform the System Check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Check pending DTCs.


k.

Turn the ignition switch off.

NOTICE:
·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



Result
Result Proceed to
P2444, P2445, P2446 and/or P2447 are output A
No pending DTC is output B



A

9.CHECK VACUUM HOSES (PRESSURE SENSOR - AIR SWITCHING VALVE)

B

9.CHECK VACUUM HOSES (PRESSURE SENSOR - AIR SWITCHING VALVE)
a.

Check the vacuum hose connections with the pressure sensor and ASV.


b.

Inspect the vacuum hose for blockages and damage.

OK:

Vacuum hose has no blockages or damage.




OK

10.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)

NG

REPAIR OR REPLACE VACUUM HOSE

10.INSPECT AIR SWITCHING VALVE ASSEMBLY (PRESSURE SENSOR)

OK

11.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS

NG

11.CHECK AIR INJECTION SYSTEM PIPE CONNECTIONS
A165786

a.

Check that all the pipes and hoses between the air pump and ASV are securely connected.


b.

Inspect the pipes and hoses for blockages and damage.

OK:

AIR system piping has no blockages or damage.




OK

12.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE AIR INJECTION SYSTEM PIPING

12.INSPECT AIR INJECTION CONTROL DRIVER (AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT)
A379601E01
1.594,0.854 2.021,1.115 0.427,0.26 1.552,2.969 1.979,3.229 0.427,0.26 4.75,0.844 5.177,1.104 0.427,0.26 4.708,3.115 5.135,3.375 0.427,0.26 1.604,1.823 1.302,2.052 true 1.573,3.875 1.24,4.146 true 4.427,3.948 4.271,4.323 true 5.208,1.719 5.438,2.073 true 4.5,1.729 4.344,2.031 true 5.271,3.948 5.49,4.313 true 0.625,0.104 2.948,0.49 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.677,2.24 3,2.625 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 3.865,0.094 6.188,0.479 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 3.896,2.281 6.219,2.667 2.323,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 1.677,0.906 2.01,1.104 0.333,0.198 10 false D48 0.906,2.01 1.333,2.208 0.427,0.198 10 false BATT 1.635,3.021 1.969,3.219 0.333,0.198 10 false D52 0.896,4.177 1.323,4.375 0.427,0.198 10 false BAT2 4.25,2.052 4.448,2.271 0.198,0.219 10 false E 5.427,2.073 5.698,2.292 0.271,0.219 10 false +B 4.823,0.885 5.156,1.083 0.333,0.198 10 false D50 4.792,3.156 5.125,3.354 0.333,0.198 10 false D54 4.135,4.365 4.563,4.563 0.427,0.198 10 false E2 5.448,4.354 5.875,4.552 0.427,0.198 10 false +B2

a.

Disconnect the D48 and D50 or D52 and D54 AID connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D50-1 (E) - Body ground Always Below 1 Ω
D54-1 (E2) - Body ground Always Below 1 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
D48-1 (BATT) - Body ground Always 11 to 14 V (near battery voltage)
D50-5 (+B) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)
D52-1 (BAT2) - Body ground Always 11 to 14 V (near battery voltage)
D54-5 (+B2) - Body ground Ignition switch ON 11 to 14 V (near battery voltage)




OK

13.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

13.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the D74 ECM connector.


b.

Disconnect the D50 or D54 AID connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D74-54 (AIRP) - D50-4 (SIP) Always Below 1 Ω
D74-53 (ARP2) - D54-4 (SIP2) Always Below 1 Ω
D74-54 (AIRP) or D50-4 (SIP) - body ground Always 10 kΩ or higher
D74-53 (ARP2) or D54-4 (SIP2) - body ground Always 10 kΩ or higher




OK

14.INSPECT AIR PUMP ASSEMBLY (BANK 1 OR BANK 2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT AIR PUMP ASSEMBLY (BANK 1 OR BANK 2)
a.
A217481E07
0.177,0.167 1.073,0.354 0.896,0.188 12 false for Bank 1: 0.146,1.604 1.042,1.792 0.896,0.188 12 false for Bank 2:

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the 400 A probe of an ammeter to the positive (+) wire of the air pump.


d.

Connect the Techstream to the DLC3.


e.

Turn the ignition switch to ON and turn the Techstream on.


f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



h.

Measure the current while the air pump is on and off.

Standard Current:
Tester Operation Air Pump ASV Specified Condition
AIR PUMP: ON, ASV: OPEN ON OPEN 10 to 40 A
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Below 1 A


NOTICE:
·

This Air Injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While AIR system operation using the Techstream is prohibited, the Techstream display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the Techstream during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Air Injection Check repeatedly may cause damage to the AIR system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.





OK

15.PERFORM ACTIVE TEST USING TECHSTREAM

NG

17.REPLACE AIR PUMP ASSEMBLY
15.PERFORM ACTIVE TEST USING TECHSTREAM
a.

Disconnect the AID connectors.


A379565E01
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.104,1.344 1.365,1.521 0.26,0.177 10 false SIV 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRV 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D50 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.323,1.313 4.708,1.5 0.385,0.188 10 false SIV2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARV2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D54 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2

b.

Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the Techstream on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



g.

Start the engine.


h.

Perform the AIR system forced operation while the engine is idling.


i.

Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


j.

Turn the ignition switch off.

NOTICE:
·

Performing Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D50-3 (SIV) - D50-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D54-3 (SIV2) - D54-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D50-3 (SIV) - D50-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D54-3 (SIV2) - D54-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



k.

Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.

A379565E02
0.875,2.75 1.292,3.01 0.417,0.26 4.052,2.792 4.469,3.052 0.417,0.26 1.656,2.927 1.49,3.24 true 1.771,2.927 1.698,3.24 true 1.896,2.927 2.01,3.229 true 2.01,2.917 2.302,3.229 true 4.927,2.958 4.76,3.271 true 5.052,2.958 5.031,3.292 true 5.198,2.958 5.396,3.281 true 5.344,2.969 5.698,3.26 true 0.479,0.385 1.552,0.583 1.073,0.198 10 false AID (for Bank 1) 2.542,0.396 2.958,0.583 0.417,0.188 10 false ECM 1.167,1.021 1.375,1.198 0.208,0.177 10 false DI 1.094,1.344 1.354,1.521 0.26,0.177 10 false SIP 2.479,1.021 2.813,1.198 0.333,0.177 10 false AIDI 2.479,1.354 2.854,1.531 0.375,0.177 10 false AIRP 0.781,1.865 3.073,2.25 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 1) 0.958,2.802 1.281,2.99 0.323,0.188 10 false D50 3.844,0.406 4.917,0.604 1.073,0.198 10 false AID (for Bank 2) 5.917,0.417 6.333,0.604 0.417,0.188 10 false ECM 4.406,1 4.667,1.188 0.26,0.188 10 false DI2 4.333,1.313 4.708,1.5 0.375,0.188 10 false SIP2 5.802,1 6.177,1.177 0.375,0.177 10 false AID2 5.792,1.313 6.208,1.49 0.417,0.177 10 false ARP2 1.406,3.271 1.573,3.479 0.167,0.208 10 false E 1.615,3.271 1.813,3.49 0.198,0.219 10 false DI 1.938,3.271 2.24,3.479 0.302,0.208 10 false SIV 2.281,3.26 2.583,3.469 0.302,0.208 10 false SIP 4.052,1.854 6.344,2.24 2.292,0.385 10 false Front view of wire harness connector: (to AID for Bank 2) 4.135,2.844 4.458,3.031 0.323,0.188 10 false D54 4.646,3.292 4.885,3.469 0.24,0.177 10 false E2 4.948,3.313 5.198,3.49 0.25,0.177 10 false DI2 5.302,3.313 5.646,3.49 0.344,0.177 10 false SIV2 5.74,3.26 6.083,3.438 0.344,0.177 10 false SIP2


l.

Connect the Techstream to the DLC3.


m.

Turn the ignition switch to ON.


n.

Turn the Techstream on.


o.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the Techstream initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



p.

Start the engine.


q.

Perform the AIR system forced operation while the engine is idling.


r.

Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.


s.

Turn the ignition switch off.

NOTICE:
·

Performing Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
D50-4 (SIP) - D50-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D54-4 (SIP2) - D54-1 (E2) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
D50-4 (SIP) - D50-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V
D54-4 (SIP2) - D54-1 (E2) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V




OK

16.REPLACE AIR INJECTION CONTROL DRIVER

NG

16.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver (See page Engine / Hybrid System>3UR-FE EMISSION CONTROL>AIR INJECTION DRIVER>REMOVAL).



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
17.REPLACE AIR PUMP ASSEMBLY

NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P2444, P2445, P2446 AND/OR P2447)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the Techstream to the DLC3.


d.

Turn the ignition switch to ON and turn the Techstream on.



f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Air injection check / Automatic Mode.


g.

Start the engine after the Techstream initialization is finished.


h.

Perform the System Check operation by pressing Next.


i.

After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.


j.

Check pending DTCs.


k.

Turn the ignition switch off.

OK:

No pending DTC is output.


NOTICE:
·

When performing the Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Air Injection Check operation finishes.





OK

NG

END