Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0505  Idle Control System Malfunction  


DESCRIPTION

The idling speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of: 1) the one valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the Throttle Position (TP) sensor, which detects the opening angle of the throttle valve; 4) the Accelerator Pedal Position (APP) sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idling speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No. DTC Detection Condition Trouble Area
P0505 Idling speed continues to vary greatly from target idling speed (2 trip detection logic)
·

ETCS

·

Air induction system

·

PCV hose connections

·

ECM



MONITOR DESCRIPTION

The ECM monitors the idling speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if the following conditions are met:

·

The difference between the target engine idling speed and actual engine idling speed exceeds the threshold and the IAC flow rate learned value is stuck at the upper or lower limit for 5 seconds or more.

·

After driving at a vehicle speed of 10 km/h (6.25 mph) or more, the difference between the target and actual engine idling speed exceeds the threshold 5 times or more during a driving cycle, and then the system determines that the IAC flow rate learned value is stuck at the upper or lower limit, or that the IAC flow rate learned value has been changed by an amount that exceeds the threshold.

A380046E01
1.042,2.615 1.156,2.615 false 1.042,1.729 1.156,1.729 false 0.635,0.74 1.479,0.938 0.844,0.198 10 false Idling Speed 0.844,1.635 1.063,1.823 0.219,0.188 10 false *1 0.833,2.531 1.052,2.719 0.219,0.188 10 false *2 2.302,1.802 3.615,2.01 1.313,0.208 10 false Target Idling Speed 2.104,2.969 3.417,3.177 1.313,0.208 10 false Actual Idling Speed 3.24,3.49 3.688,3.719 0.448,0.229 10 false Time 0.917,3.375 1.073,3.542 0.156,0.167 10 false 0 4.542,2.344 4.698,2.51 0.156,0.167 10 false 0 4.281,1.552 4.719,1.74 0.438,0.188 10 false Large 4.271,3.063 4.708,3.25 0.438,0.188 10 false Small 6.302,3.646 6.75,3.875 0.448,0.229 10 false Time 4.052,0.833 5.698,1.021 1.646,0.188 10 false Learned Idling Air Volume 6.271,1.229 6.938,1.417 0.667,0.188 10 false Maximum 6.333,2.74 7,2.927 0.667,0.188 10 false Minimum 1.115,3.792 6,4 4.885,0.208 10 false *1: 150 rpm above target Idling speed (A/C off and NSW off) 1.115,4.115 4.844,4.365 3.729,0.25 10 false *1: 200 rpm above target Idling speed (A/C on or NSW on) 1.125,4.427 3.656,4.615 2.531,0.188 10 false *2: 100 rpm below target Idling speed


MONITOR STRATEGY

Related DTCs P0505: ISC function
Required Sensors/Components (Main) ETCS
Required Sensors/Components (Related) Crankshaft position sensor, Engine coolant temperature sensor, and Vehicle speed sensor
Frequency of Operation Once per driving cycle
Duration 5 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not stored P0010, P0020 (Camshaft Timing Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0013, P0023 (Exhaust Camshaft Timing Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air Fuel Ratio Sensor Heater)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0171, P0172, P0174, P0175 (Fuel System)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0351 - P0358 (Igniter)
P0451, P0452, P0453 (EVAP System)
P0500 (Vehicle Speed Sensor)
P0705 (Shift Lever Position Switch)
P0748, P0778 (Pressure Control Solenoid)
P0973, P0974, P0976, P0977, P0979, P0980, P0982, P0983, P0985, P0986 (Shift Solenoid)
Engine Running

TYPICAL MALFUNCTION THRESHOLDS

Either condition is met 1 or 2
1. Both of following conditions A and B met -
A. Engine speed - Target engine speed Less than -100 rpm, or more than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or more than 200 rpm (A/C on or NSW on)
B. IAC flow rate learned value 2.48 L/sec. or less, or 11.0 L/sec. or more for 5 seconds or more
2. Both of following conditions C and D met -
C. Frequency that both of following conditions (a) and (b) met 5 times or more
(a) Engine speed - Target engine speed Less than -100 rpm, or more than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or more than 200 rpm (A/C on or NSW on)
(b) Vehicle condition Stopped after being driven at 10 km/h (6.25 mph) or more
D. Either condition is met (c) or (d)
(c) IAC flow rate learned value 2.48 L/sec. or less, or 11.0 L/sec. or more
(d) Amount of change of IAC flow rate learned value +2.86 L/sec. or more, or -4.69 L/sec. or less

CONFIRMATION DRIVING PATTERN

A231468E06
0.606,1.193 1.876,1.395 1.27,0.203 10 10 km/h (6.25 mph) 1.412,2.029 1.828,2.19 0.416,0.161 10 Idling 0.648,2.379 1.862,2.739 1.213,0.36 10 Ignition Switch ON 2.356,2.536 2.549,2.724 0.193,0.189 10 [A] 2.75,2.239 2.965,2.395 0.214,0.156 10 [B] 6.306,3.309 6.527,3.483 0.221,0.175 10 [F] 2.313,3.523 3.559,3.68 1.246,0.156 10 5 minutes or more 4.607,3.385 5.914,3.541 1.307,0.156 10 20 seconds or more 4.557,2.949 4.875,3.365 4.875,3.365 4.025,2.949 false 5.744,2.949 5.104,3.337 5.104,3.337 5.127,2.949 false 3.616,0.976 3.865,1.169 0.249,0.193 10 [E] 5.929,0.963 6.178,1.157 0.249,0.193 10 [E] 5.35,0.967 5.598,1.16 0.249,0.193 10 [E] 4.776,0.969 5.025,1.162 0.249,0.193 10 [E] 4.203,0.974 4.452,1.167 0.249,0.193 10 [E] 3.121,2.244 3.342,2.419 0.221,0.175 10 [C] 1.829,3.15 2.62,3.315 0.791,0.166 10 Warming up 3.322,3.309 3.543,3.483 0.221,0.175 10 [D] 2.838,2.958 2.614,3.229 false 3.184,2.949 2.576,3.514 false

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

7.

Idle the engine for 5 minutes or more [C].

HINT:

In order to keep idling stable, turn off the A/C and all other electrical loads and do not perform any shift operations.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0505.

12.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].



13.

Accelerate the vehicle to 10 km/h (6.25 mph) or more, and then idle the engine for 20 seconds or more [E].

14.

Repeat step [E] 5 times.

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].

16.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

18.

Input the DTC: P0505.

19.

Check the DTC judgment result.

Techstream Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



20.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

The following conditions may also cause DTC P0505 to be set:

1.

The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.

2.

The accelerator pedal being not fully released.


·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0505 is output A
P0505 and other DTCs are output B

HINT:

If any DTCs other than P0505 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

PCV hose is connected correctly and is not damaged.




OK

3.CHECK AIR INDUCTION SYSTEM

NG

3.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FBE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

4.CHECK THROTTLE VALVE

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

4.CHECK THROTTLE VALVE
a.

Check the throttle valve condition.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.


HINT:

Perform "Inspection After Repair" after replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG