Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  P0017  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)  P0018  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)  P0019  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. DTC Detection Condition Trouble Area
P0016 Deviation in crankshaft position sensor signal and VVT sensor 1 (for Intake Side of Bank 1) signal (2 trip detection logic)
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

OCV (for intake side)

·

OCV filter

·

Camshaft timing gear assembly

·

ECM


P0017 Deviation in crankshaft position sensor signal and VVT sensor 1 (for Exhaust Side of Bank 1) signal (2 trip detection logic)
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

OCV (for exhaust side)

·

OCV filter

·

Camshaft timing exhaust gear assembly

·

ECM


P0018 Deviation in crankshaft position sensor signal and VVT sensor 2 (for Intake Side of Bank 2) signal (2 trip detection logic)
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

OCV (for intake side)

·

OCV filter

·

Camshaft timing gear assembly

·

ECM


P0019 Deviation in crankshaft position sensor signal and VVT sensor 2 (for Exhaust Side of Bank 2) signal (2 trip detection logic)
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

OCV (for exhaust side)

·

OCV filter

·

Camshaft timing exhaust gear assembly

·

ECM



MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0016 (Bank 1) or P0018 (Bank 2).

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learning value while the engine is idling. The VVT learning value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learning value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and sets the DTC P0017 (Bank 1) or P0019 (Bank 2).

MONITOR STRATEGY

Related DTCs P0016: Camshaft timing misalignment at idling (Bank 1 Intake Side)
P0017: Camshaft timing misalignment at idling (Bank 1 Exhaust Side)
P0018: Camshaft timing misalignment at idling (Bank 2 Intake Side)
P0019: Camshaft timing misalignment at idling (Bank 2 Exhaust Side)
Required Sensors/Components (Main) VVT actuator
Required Sensors/Components (Related) Camshaft position sensor, Crankshaft position sensor
Frequency of Operation Continuous
Duration Within 1 minute
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Intake Side
Engine speed 400 to 1400 rpm

Exhaust Side
Engine speed 400 to 1400 rpm

TYPICAL MALFUNCTION THRESHOLDS

Intake side:
One of following conditions met -
VVT learning value when camshaft maximum retarded Less than 22.23°CA
VVT learning value when camshaft maximum retarded More than 46.68°CA

Exhaust side:
One of following conditions met -
VVT learning value when camshaft maximum advanced Less than 82.23°CA
VVT learning value when camshaft maximum advanced More than 106.68°CA

CONFIRMATION DRIVING PATTERN

A197314E01
0.161,0.66 1.086,0.809 0.924,0.149 10 Vehicle Speed 1.514,2.102 1.719,2.303 0.205,0.201 10 [A] 2.162,1.659 2.388,1.829 0.225,0.170 10 [B] 3.188,1.648 3.396,1.801 0.208,0.152 10 [C] 3.826,3.013 4.037,3.169 0.211,0.156 10 [D] 4.681,0.853 4.875,1.047 0.194,0.194 10 [E] 5.656,1.617 5.850,1.811 0.194,0.194 10 [F] 6.372,3.021 6.614,3.205 0.243,0.184 10 [G] 0.667,1.753 1.052,1.937 0.385,0.184 10 Idling 4.815,0.256 6.292,0.618 1.477,0.362 10 There is no designated vehicle speed 0.209,2.034 1.138,2.349 0.928,0.316 10 Ignition Switch ON 1.907,2.503 2.698,2.839 0.791,0.336 10 Warming up the engine 2.737,2.524 3.893,2.687 1.156,0.163 10 5 minutes or more 5.266,2.531 6.421,2.694 1.156,0.163 10 5 minutes or more 4.121,2.566 5.020,2.736 0.899,0.170 10 2 to 3 minutes 4.257,1.074 4.6,0.443 4.6,0.443 4.754,0.443 false

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on [A].

6.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0016, P0017, P0018 or P0019.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].

16.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

18.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
P0016, P0017, P0018 or P0019 is output A
P0016, P0017, P0018 or P0019 and other DTCs are output B



A

2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE OCV)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the Techstream to the DLC3.


b.

Start the engine and turn the Techstream on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) or Control the VVT Exhaust Linear (Bank 1) or Control the Exhaust VVT Linear (Bank 2) / All Data / VVT Change Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #1, VVT Ex Chg Angle #2.


e.

Perform the Active Test. Check that the displacement angle varies.

OK:

Varies




OK

3.CHECK ENGINE MECHANICAL SYSTEM

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST SIDE)
3.CHECK ENGINE MECHANICAL SYSTEM
a.

Check the engine mechanical system (See page Engine / Hybrid System>3UR-FBE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION).



NEXT

7.CONFIRM WHETHER DTC OUTPUT RECURS
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST SIDE)
a.

Inspect the camshaft timing oil control valve assembly (for intake or exhaust side) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

5.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKEOR EXHAUST SIDE)

5.INSPECT OIL CONTROL VALVE FILTER

OK

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY OR CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly or camshaft timing exhaust gear assembly (See page Engine / Hybrid System>3UR-FBE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY).

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly or camshaft timing exhaust gear assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

7.CONFIRM WHETHER DTC OUTPUT RECURS
7.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON and turn the Techstream on.



d.

Start the engine and warm it up.


e.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


f.

Read the output pending DTCs using the Techstream.

OK:

No pending DTC output.




OK

END

NG