1.REMOVE OIL FILTER ELEMENT
15781
2.REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)
15671
3.REMOVE OIL FILTER BRACKET (w/ Oil Cooler)
15671
4.REMOVE OIL FILTER BRACKET (w/o Oil Cooler)
13471
5.REMOVE CRANKSHAFT PULLEY
12108
6.REMOVE OIL FILLER CAP SUB-ASSEMBLY
12185
7.REMOVE OIL FILLER CAP HOUSING
Remove the 2 bolts, filler cap housing and gasket.
19100P
8.REMOVE SPARK PLUG
9.REMOVE VVT SENSOR
LH:
Remove the 2 bolts and 2 VVT sensors.
RH:
Remove the 2 bolts and 2 VVT sensors.
11102A
10.REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and camshaft position sensor.
19312
11.REMOVE CRANK POSITION SENSOR PROTECTOR
Remove the 2 bolts and sensor protector.
15100R
12.REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and crankshaft position sensor.
15330B
13.REMOVE CAMSHAFT OIL CONTROL VALVE ASSEMBLY
LH:
Remove the 2 bolts and 2 oil control valves.
RH:
Remove the 2 bolts and 2 oil control valves.
11202
14.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
11201
15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
15678A
16.REMOVE OIL CONTROL VALVE FILTER
LH:
Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.
RH:
Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.
11193
17.REMOVE SPARK PLUG TUBE GASKET
Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
Using a screwdriver, pry out the gaskets.
Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.
Tape the screwdriver tip before use.
Be careful not to damage the cylinder head cover.
16100
18.REMOVE WATER PUMP ASSEMBLY
11302
19.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
16322
20.REMOVE WATER INLET PIPE
11301C
21.REMOVE FRONT CRANKSHAFT OIL SEAL
Place the timing chain cover on wooden blocks.
Place the oil pump on a wooden block.
Using a screwdriver and wooden block, pry out the oil seal.
Tape the screwdriver tip before use.
Do not damage the surface of the oil seal press fit hole.
22.SET NO. 1 CYLINDER TO TDC / COMPRESSION
Temporarily install the pulley set bolt.
Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.
If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.
13540
23.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.
Remove the 2 bolts, chain tensioner and gasket.
13559
24.REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH
13561
25.REMOVE NO. 1 CHAIN VIBRATION DAMPER LH
Remove the 2 bolts and chain vibration damper.
13506
26.REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH
While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing gear.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Be careful not to damage the cylinder head with the wrench.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.
Remove the No. 1 and No. 2 chains from the gears.
13560A
27.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the 2 bolts and chain tensioner.
13540
28.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.
Remove the 2 bolts and chain tensioner.
13559
29.REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH
13561
30.REMOVE NO. 1 CHAIN VIBRATION DAMPER RH
Remove the 2 bolts and vibration damper.
13506
31.REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH
While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing gear.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Be careful not to damage the cylinder head with the wrench.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.
Remove the No. 1 and No. 2 chains from the gears.
13550
32.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the 2 bolts and chain tensioner.
13521A
33.REMOVE CRANKSHAFT TIMING GEAR KEY
Using a screwdriver, remove the 2 timing gear keys from the crankshaft.
34.REMOVE CAMSHAFT BEARING CAP LH
Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 6 bearing caps.
Arrange the removed parts in the correct order.
Remove the No. 3 and No. 4 camshafts.
Arrange the removed parts in the correct order.
11104A
35.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
Tape the screwdriver tip before use.
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.
36.REMOVE CAMSHAFT BEARING CAP RH
Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 6 bearing caps.
Arrange the removed parts in the correct order.
Remove the No. 1 and No. 2 camshafts.
Arrange the removed parts in the correct order.
11103C
37.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
Tape the screwdriver tip before use.
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.
13801
38.REMOVE VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 32 valve rocker arms from the cylinder head.
Arrange the removed parts in the correct order.
13750
39.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 32 valve lash adjusters from the cylinder head.
Arrange the removed parts in the correct order.
13716
40.REMOVE VALVE STEM CAP
Remove the 32 valve stem caps from the cylinder head.
Arrange the removed parts in the correct order.
11101
41.REMOVE CYLINDER HEAD SUB-ASSEMBLY LH
11102
42.REMOVE CYLINDER HEAD SUB-ASSEMBLY RH
11116
43.REMOVE CYLINDER HEAD GASKET LH
11115
44.REMOVE CYLINDER HEAD GASKET RH
11445
45.REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the 2 water jacket spacers from the cylinder head.
Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.
12203A
46.REMOVE VENTILATION PIPE GASKET
Using a screwdriver, pry out the ventilation pipe gasket.
Tape the screwdriver tip before use.
16877
47.REMOVE NO. 1 HEAT EXCHANGER COVER
Remove the 12 bolts and 2 nuts.
Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.
Tape the screwdriver tip before use.
12102A
48.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 14 bolts and 2 nuts.
Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
Be careful not to damage the contact surfaces of the oil pans.
12101
49.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY
Remove the 14 bolts and 2 nuts.
Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
Tape the screwdriver tip before use.
Be careful not to damage the contact surfaces of the cylinder block and oil pan.
12121
50.REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 7 bolts and baffle plate.
15104
51.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 bolts, oil strainer and O-ring.
11381
52.REMOVE ENGINE REAR OIL SEAL RETAINER
Remove the 6 bolts and oil seal retainer.
Using a screwdriver, pry out the oil seal retainer.
Tape the screwdriver tip before use.
12109A
53.REMOVE OIL DRAIN PIPE SUB-ASSEMBLY
Remove the bolt and oil drain pipe.
Remove the O-ring.
11381A
54.REMOVE REAR CRANKSHAFT OIL SEAL
Place the oil seal retainer on wooden blocks.
Using a screwdriver and hammer, tap out the oil seal.
55.REMOVE RING PIN
It is not necessary to remove the ring pin unless it is being replaced.
56.REMOVE STUD BOLT
If the stud bolt is deformed or its threads are damaged, replace it.