Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0128  Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)  


DESCRIPTION

This DTC is stored when the Engine Coolant Temperature (ECT) does not reach 75°C (167°F) despite sufficient engine warm-up time having elapsed.

DTC No. DTC Detection Condition Trouble Area
P0128

Conditions (a), (b) and (c) met for 5 seconds (2 trip detection logic):

(a) Cold start

(b) Engine warmed up

(c) ECT less than 75°C (167°F)


·

Thermostat

·

Cooling system

·

Engine coolant temperature sensor

·

ECM



MONITOR DESCRIPTION

A121605E56
3.74,2.208 3.26,1.24 false 4.865,2.333 5.156,2.677 false 4.458,2.719 5.938,2.906 1.479,0.188 10 false Indicated ECT Reading 3.188,3.688 5.5,3.885 2.313,0.198 10 false DTC Stored (after 2 Driving Cycles) 2.25,1.146 3.24,1.365 0.99,0.219 10 false Estimated ECT 0.156,1.688 1.771,1.875 1.615,0.188 10 false Threshold (75°C (167°F)) 4.281,1.01 4.969,1.177 0.688,0.167 10 false 5 seconds 1.802,2.854 2.125,3.063 0.323,0.208 10 false ECT 2.292,3.323 2.667,3.542 0.375,0.219 10 false Time

The ECM estimates the ECT based on the starting temperature, engine loads, and engine speeds. The ECM then compares the estimated temperature with the actual ECT. When the estimated ECT reaches 75°C (167°F), the ECM checks the actual ECT. If the actual ECT is less than 75°C (167°F), the ECM interprets this as a malfunction in the thermostat or the engine cooling system and sets the DTC.

MONITOR STRATEGY

Related DTCs P0128: Coolant Thermostat
Required Sensors/Components (Main) Thermostat
Required Sensors/Components (Related) Engine Coolant Temperature (ECT) sensor, Intake Air Temperature (IAT) sensor, Vehicle speed sensor
Frequency of Operation Once per driving cycle
Duration 710 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not stored P0010, P0020 (Camshaft Timing Oil Control Valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0013, P0023 (Exhaust Camshaft Timing Oil Control Valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air Fuel Ratio Sensor Heater)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Meter)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0171, P0172, P0174, P0175 (Fuel System)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P0301 - P0308 (Misfire)
P0335 (Crankshaft Position Sensor)
P1340 (Camshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0351 - P0358 (Igniter)
P0500 (Vehicle Speed Sensor)
Battery voltage 11 V or more
Either of following conditions 1 or 2 met: -
1. All of following conditions met: -
·

ECT at engine start - IAT at engine start


-15 to 7°C (-27 to 12.6°F)
·

ECT at engine start


-10 to 56°C (14 to 133°F)
·

IAT at engine start


-10 to 56°C (14 to 133°F)
2. All of following conditions met: -
·

ECT at engine start - IAT at engine start


More than 7°C (12.6°F)
·

ECT at engine start


56°C (133°F) or less
·

IAT at engine start


-10°C (14°F) or more
Accumulated time at 128 km/h (80 mph) or more of vehicle speed Less than 20 seconds

TYPICAL MALFUNCTION THRESHOLDS

Duration that both of following conditions (a) and (b) met 5 seconds or more
(a) Estimated ECT 75°C (167°F) or more
(b) ECT sensor output Below 75°C (167°F)

CONFIRMATION DRIVING PATTERN

A255184E06
0.135,1.271 1.292,1.469 1.156,0.198 10 false 80 km/h (50 mph) 0.094,1.646 1.333,1.854 1.24,0.208 10 false Ignition Switch ON 2.406,1.125 2.646,1.333 0.24,0.208 10 false [B] 4.823,2.958 5.063,3.167 0.24,0.208 10 false [C] 1.802,1.51 2.073,1.708 0.271,0.198 10 false [A] 3.167,2.292 3.969,2.5 0.802,0.208 10 false 12 minutes 2.938,0.063 6.938,0.271 4,0.208 10 false - Engine coolant temperature when engine started: 56°C or less 2.938,0.385 6.938,0.594 4,0.208 10 false - Intake air temperature when engine started: 0 to 35°C 2.938,0.75 7.115,0.958 4.177,0.208 10 false - Heater set to MAX HOT with fresh air mode selected and A/C off

1.

Stop the engine and allow it to soak.

2.

Connect the Techstream to the DLC3.

3.

Turn the ignition switch to ON and turn the Techstream on [A].

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp and Intake Air.

5.

Check that "Coolant Temp" is 56°C (133°F) or less and "Intake Air" is between 0 and 35°C (0 and 95°F).

6.

Set the heater to MAX HOT with fresh air mode selected and turn the A/C off.

7.

Start the engine and drive the vehicle at 80 km/h (50 mph) for 12 minutes [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Data can be captured relatively easily by using the snapshot function in the Data List.

·

Enter the following menus: Data List / Function / Snap-shot configuration / Record time / 5 min.

·

Data capture can be started by using the target point function. For example, setting the target point to an engine speed of 4000 rpm and then racing the engine, etc. to raise the engine speed to a speed of 4000 rpm or more will cause data capture to start.



8.

After "Coolant Temp" stabilizes, check that "Coolant Temp" is 75°C (167°F) or higher [C].

HINT:

IF "Coolant Temp" is below 75°C (167°F) while driving the vehicle at 80 km/h (50 mph), inspect the cooling system and thermostat.



CAUTION / NOTICE / HINT

HINT:
·

This DTC relates to the thermostat.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0128)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
P0128 is output A
P0128 and other DTCs are output B

HINT:

If any DTCs other than P0128 are output, troubleshoot those DTCs first.




A

2.CHECK COOLING SYSTEM

B

2.CHECK COOLING SYSTEM
a.

Check for defects in the cooling system that might cause the system to be too cold, such as abnormal radiator fan operation or any modifications.



OK

3.INSPECT THERMOSTAT

NG

REPAIR OR REPLACE COOLING SYSTEM

3.INSPECT THERMOSTAT
a.

b.

Measure the valve opening temperature of the thermostat.

Standard opening temperature:

80 to 84°C (176 to 183°F)


HINT:

In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.



c.


OK

4.INSPECT ENGINE COOLANTTEMPERATURE SENSOR

NG

4.INSPECT ENGINE COOLANTTEMPERATURE SENSOR
a.

Inspect the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG