Refer to DTC P2195 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P2195).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2237
P2240 |
Open in the circuit between terminals A1A+/A2A+ and A1A-/A2A- of the A/F sensor while engine is running
(2 trip detection logic) |
·
Open in Air Fuel Ratio (A/F) sensor (for Bank 1, 2 Sensor 1) circuit ·
Air Fuel Ratio (A/F) sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2238
P2241 |
·
Case 1: Condition (a) or (b) continues for 5.0 seconds or more (2 trip detection logic): (a) A1A+/A2A+ voltage 0.5 V or less (b) (A1A+/A2A+) - (A1A-/A2A-) = 0.1 V or less ·
Case 2: A/F sensor admittance: Less than 0.0054 1/Ω (2 trip detection logic) |
·
Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit ·
A/F sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2239
P2242 |
Condition (a) or (b) continues for 5.0 seconds or more
(2 trip detection logic): (a) A1A+/A2A+ voltage more than 4.5 V (b) (A1A+/A2A+) - (A1A-/A2A-) = more than 0.8 V |
·
Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit ·
A/F sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2252
P2255 |
A1A-/A2A- voltage 0.5 V or less for 5.0 seconds or more
(2 trip detection logic) |
·
Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit ·
A/F sensor (for Bank 1, 2 Sensor 1) ·
ECM |
| P2253
P2256 |
A1A-/A2A- voltage more than 4.5 V for 5.0 seconds or more
(2 trip detection logic) |
·
Open or short in A/F sensor (for Bank 1, 2 Sensor 1) circuit ·
A/F sensor (for Bank 1, 2 Sensor 1) ·
ECM |
DTCs P2237, P2238, P2239, P2252 and P2253 indicate malfunctions related to the bank 1 A/F sensor circuit.
DTCs P2240, P2241, P2242, P2255 and P2256 indicate malfunctions related to the bank 2 A/F sensor circuit.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
These DTCs are output when there is an open or short in the A/F sensor circuit, or if A/F sensor output drops.
To detect these problems, the voltage of the A/F sensor is monitored when turning the ignition switch to the ON position, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the A/F sensor is between 0.5 V and 4.5 V, it is considered normal. If the voltage is outside of the specified range, or the admittance is less than the standard value, the ECM will determine that there is a malfunction in the A/F sensor. If the same malfunction is detected in the next driving cycle, the MIL is illuminated and a DTC is stored.
The Air-Fuel Ratio (A/F) sensor varies its output voltage in proportion to the air-fuel ratio. If the A/F sensor impedance (alternating current resistance) or output voltage deviates greatly from the standard range, the ECM determines that there is an open or short in the A/F sensor circuit.
| Related DTCs | P2237: A/F sensor (for Bank 1) open circuit between A1A+ and A1A-
P2238: A/F sensor (for Bank 1) short circuit between A1A+ and A1A- P2238: A/F sensor (for Bank 1) short circuit between A1A+ and GND P2238: A/F sensor (for Bank 1) low impedance P2239: A/F sensor (for Bank 1) short circuit between A1A+ and +B P2239: A/F sensor (for Bank 1) short circuit between A1A+ and +B, A1A- and GND P2240: A/F sensor (for Bank 2) open circuit between A2A+ and A2A- P2241: A/F sensor (for Bank 2) short circuit between A2A+ and A2A- P2241: A/F sensor (for Bank 2) short circuit between A2A+ and GND P2241: A/F sensor (for Bank 2) low impedance P2242: A/F sensor (for Bank 2) short circuit between A2A+ and +B P2242: A/F sensor (for Bank 2) short circuit between A2A+ and +B, A2A- and GND P2252: A/F sensor (for Bank 1) short circuit between A1A- and GND P2253: A/F sensor (for Bank 1) short circuit between A1A- and +B P2255: A/F sensor (for Bank 2) short circuit between A2A- and GND P2256: A/F sensor (for Bank 2) short circuit between A2A- and +B |
| Required Sensors/Components (Main) | A/F sensor |
| Required Sensors/Components (Related) | Engine Coolant Temperature (ECT) sensor, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 10 seconds: P2237, P2240 (open circuit) and P2238, P2241 (low impedance)
5 seconds: Other |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P1340 (Camshaft position sensor) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P0451, P0452, P0453 (EVAP system) P2440 - P2447 (Secondary air injection system) P0500, P0722 (Vehicle Speed Sensor) P0505 (IAC valve) |
| Monitor runs whenever following DTCs not present | None |
| Battery voltage | 11 V or more |
| Engine | Running |
| Estimated sensor temperature | 450 to 550°C (842 to 1022°F) for P2237 and P2240 |
| Engine coolant temperature | 0°C (0°F) or higher |
| Estimated sensor temperature | 700 to 800°C (1292 to 1472°F) for P2238 and P2241 |
| Fuel cut | Not executed |
| Battery voltage | 11 V or higher |
| Ignition switch | ON |
| Timing after ignition switch is OFF to ON | 5 seconds or more |
| A/F sensor admittance | Below 0.0018 1/Ω |
| A/F sensor admittance | Less than 0.0054 1/Ω |
| A1A+/A2A+ terminal voltage | 0.5 V or less |
| A1A+/A2A+ terminal voltage | More than 4.5 V |
| A1A-/A2A- terminal voltage | 0.5 V or less |
| A1A-/A2A- terminal voltage | More than 4.5 V |
| Difference between A1A+ and A1A-/A2A+ and A2A- terminal voltage | 0.1 V or less |
| Difference between A1A+ and A1A-/A2A+ and A2A- terminal voltage | More than 0.8 V |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the Techstream on.
Start the engine and wait 5 minutes.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTC.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Refer to DTC P2195 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P2195).
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Bank 2 refers to the bank that does not include the No. 1 cylinder.
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
OK
NG
Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).
Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 is output | B |
A
B