Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM J

3UR-FBE ENGINE CONTROL  SFI SYSTEM  Fuel Injection System  


DESCRIPTION

This inspection procedure should be performed when the air-fuel ratio is extremely rich or lean.

PROCEDURE

1.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections (See page Engine / Hybrid System>3UR-FBE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

PCV hose is connected correctly and is not damaged.




OK

2.CHECK AIR INDUCTION SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

2.CHECK AIR INDUCTION SYSTEM
HINT:

If a malfunction occurs when depressing the brake pedal, inspect the brake booster assembly, as there may be a vacuum leak in the brake booster assembly itself.


a.

Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FBE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from air induction system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

3.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

3.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
a.

Connect the Techstream to the DLC3.


b.

Start the engine.


c.

Turn the Techstream on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Control the Injection Volume operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(Air fuel ratio)
+12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2 or O2S B2S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 or AFS Voltage B2S1 Status of O2S B1S2 or O2S B2S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector blockage

·

Gas leaks from exhaust system

·

Air induction system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


A
Rich Rich Actual air fuel ratio rich
·

Fuel injector leaks or blockage

·

Gas leaks from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


A
Lean Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction
·

Air fuel ratio sensor


B

Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the AFS Voltage is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output voltage of the heated oxygen sensor alternates correctly.



A

4.READ VALUE USING TECHSTREAM (COOLANT TEMP)

B

10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
4.READ VALUE USING TECHSTREAM (COOLANT TEMP)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


e.

Read the Coolant Temp twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: Between 75°C and 100°C (167°F and 212°F).


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

5.READ VALUE USING TECHSTREAM (MAF)

NG

5.READ VALUE USING TECHSTREAM (MAF)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or more.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:

Between 18.0 gm/sec and 27.0 gm/sec (shift lever: N; A/C: Off).




OK

6.CHECK FUEL PRESSURE

NG

15.CHECK HARNESS AND CONNECTOR
6.CHECK FUEL PRESSURE

OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leakage.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

8.CHECK FOR SPARK (SPARK TEST)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>3UR-FBE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Cylinder #1 Misfire Count (to Cylinder #8 Misfire Count).





NEXT

9.CHECK FUEL INJECTOR (INJECTION AND VOLUME)
9.CHECK FUEL INJECTOR (INJECTION AND VOLUME)
a.

Check the injection and volume.

HINT:
·

Refer to the fuel injector assembly inspection procedure (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL INJECTOR>INSPECTION).

·

If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the Techstream. Enter the following menus: Powertrain / Engine and ECT / Data List / Gas Misfire / Cylinder #1 Misfire Count (to Cylinder #8 Misfire Count).

·

Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





OK

10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

NG

10.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

11.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

NG

11.CHECK TERMINAL VOLTAGE (+B OF AIR FUEL RATIO SENSOR)

OK

12.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

20.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY)
12.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the D33 or D34 A/F sensor connector.


b.

Disconnect the D74 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
D33-1 (HA1A) - D74-22 (HA1A) Always Below 1 Ω
D33-3 (A1A+) - D74-126 (A1A+) Always Below 1 Ω
D33-4 (A1A-) - D74-125 (A1A-) Always Below 1 Ω
D34-1 (HA2A) - D74-20 (HA2A) Always Below 1 Ω
D34-3 (A2A+) - D74-103 (A2A+) Always Below 1 Ω
D34-4 (A2A-) - D74-102 (A2A-) Always Below 1 Ω
D33-1 (HA1A) or D74-22 (HA1A) - Body ground Always 10 kΩ or higher
D33-3 (A1A+) or D74-126 (A1A+) - Body ground Always 10 kΩ or higher
D33-4 (A1A-) or D74-125 (A1A-) - Body ground Always 10 kΩ or higher
D34-1 (HA2A) or D74-20 (HA2A) - Body ground Always 10 kΩ or higher
D34-3 (A2A+) or D74-103 (A2A+) - Body ground Always 10 kΩ or higher
D34-4 (A2A-) or D74-102 (A2A-) - Body ground Always 10 kΩ or higher




OK

13.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern section of the DTC inspection procedure that was being performed before coming to this fuel injection system inspection procedure.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC that was output before coming to this fuel injection system inspection procedure is output A
DTC is not output B



A

15.CHECK HARNESS AND CONNECTOR

B

END

15.CHECK HARNESS AND CONNECTOR
a.

Check the connection and terminal contact pressure of the connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern section of the DTC inspection procedure that was being performed before coming to this fuel injection system inspection procedure.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC that was output before coming to this fuel injection system inspection procedure is output A
DTC is not output B



A

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

18.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the result of the inspection performed in step 5 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Start the engine and warm it up.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern section of the DTC inspection procedure that was being performed before coming to this fuel injection system inspection procedure.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
DTC is not output A
DTC that was output before coming to this fuel injection system inspection procedure is output B



A

END

B

20.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - INTEGRATION RELAY)

OK

21.INSPECT INTEGRATION RELAY (A/F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT INTEGRATION RELAY (A/F)

OK

NG

REPLACE INTEGRATION RELAY