Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

Refer to DTC P0115 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0115).

DTC No. DTC Detection Condition Trouble Area
P0116 When either of following conditions met (2 trip detection logic):
·

When cold engine started and engine warmed up, Engine Coolant Temperature (ECT) sensor value does not change.

·

After warmed up engine stopped and then next cold engine start performed, ECT sensor value does not change.


·

Thermostat

·

Engine Coolant Temperature (ECT) sensor



MONITOR DESCRIPTION

Engine coolant temperature (ECT) sensor cold start monitor

When a cold engine start is performed and then the engine is warmed up, if the ECT sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


ECT sensor soak monitor

If the ECT sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


MONITOR STRATEGY

Related DTCs P0116: Engine coolant temperature (ECT) sensor cold start monitor
P0116: ECT sensor soak monitor
Required Sensors/Components (Main) ECT sensor
Required Sensors/Components (Related) None
Frequency of Operation Once per driving cycle
Duration -: Cold start monitor
10 seconds: Soak monitor
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

ECT sensor cold start monitor:
Monitor runs whenever following DTCs not stored None
Battery voltage 10.5 V or more
Time after engine start 1 second or more
ECT at engine start Less than 60°C (140°F)
Soak time 0 seconds or more
Accumulated MAF 8727 g or more
Fuel cut OFF
Difference between ECT at engine start and IAT Less than 40°C (72°F)
Intake air temperature sensor circuit failure (P0112, P0113) Not detected
Engine coolant temperature circuit failure (P0115, P0117, P0118, P0125) Not detected
Thermostat failure (P0128) Not detected

ECT sensor soak monitor:
Monitor runs whenever following DTCs not stored None
Battery voltage 10.5 V or more
Engine Running
Soak time 5 hours or more
Either (a) or (b) condition met -
(a) ECT 60°C (140°F) or more
(b) Accumulated MAF 17454 g or more
Intake air temperature sensor circuit failure (P0112, P0113) Not detected
Engine coolant temperature circuit failure (P0115, P0117, P0118, P0125) Not detected
Thermostat failure (P0128) Not detected
Soak timer circuit failure (P2610) Not detected

TYPICAL MALFUNCTION THRESHOLDS

ECT sensor cold start monitor:
ECT sensor value change Less than 5°C (9°F)

ECT sensor soak monitor:
Difference between current ECT sensor value and previous ECT sensor value when engine stopped Less than 5°C (9°F) [varies with ECT of last trip engine stop]

COMPONENT OPERATING RANGE

ECT ECT sensor value changes in accordance with actual ECT

CONFIRMATION DRIVING PATTERN

A198823E91
0.25,1.135 1.406,1.333 1.156,0.198 10 false 40 km/h (25 mph) 1.042,1.76 1.458,1.979 0.417,0.219 10 false Idling 2.74,2.521 3.958,2.688 1.219,0.167 10 false 5 minutes or more 4.125,0.167 5.854,0.354 1.729,0.188 10 false Total of 5 minutes or more 2.073,1.917 2.313,2.083 0.24,0.167 10 false [A] 3.25,1.615 3.448,1.813 0.198,0.198 10 false [B] 4.01,2.875 4.26,3.073 0.25,0.198 10 false [C] 6.135,2.875 6.375,3.052 0.24,0.177 10 false [E] 0.229,2.042 1.438,2.219 1.208,0.177 10 false Ignition Switch ON 4.833,0.656 5.135,0.833 0.302,0.177 10 false [D] 1.385,3.188 6.708,3.396 5.323,0.208 10 false HINT: Start the engine when the engine coolant temperature is 60°C (140°F) or less

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

4.

Check that the coolant temperature is 60°C (140°F) or less.

5.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the Techstream on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

HINT:

If the engine coolant temperature does not change by 5°C (9°F) or more, the ECT sensor is malfunctioning. It is not necessary to continue this procedure.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0116.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].


14.

Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [D].

HINT:

In the event of the drive pattern being interrupted (possibly due to factors such as traffic conditions), the drive pattern can be resumed.


15.

Check the DTC judgment result again [E].

16.

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.

17.

If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

If DTC P0115, P0117, P0118 or P0125 is set simultaneously with DTC P0116, the ECT sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTC.

Result
Result Proceed to
P0116 is output A
P0116 and other DTCs are output B



A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

b.

Measure the valve opening temperature of the thermostat.

Standard opening temperature:

80 to 84°C (176 to 183°F)


HINT:

In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.



c.

Reinstall the thermostat (See page Engine / Hybrid System>3UR-FBE COOLING>THERMOSTAT>INSTALLATION).

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




OK

NG