Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › SFI SYSTEM › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233928 SFI SYSTEM C

3UR-FBE ENGINE CONTROL  SFI SYSTEM  P050B  Cold Start Ignition Timing Performance  


DESCRIPTION

This monitor will run when the engine is started at an engine coolant temperature of -10 to 50°C (14 to 122°F). The DTC will be set after the engine idles for 13 seconds (2 trip detection logic).

The DTC is designed to monitor the ignition timing at cold start. When the engine is started at an engine coolant temperature of lower than 50°C (122°F), the ECM checks the ignition timing at engine idling. If the ignition timing advances beyond the specified level within 10 seconds, the ECM interprets this as a malfunction. The MIL is illuminated and a DTC is set when the malfunction is detected in consecutive driving cycles (2 trip detection logic).

NOTICE:

When the negative battery terminal is disconnected during inspections or repairs, the ISC (Idle Speed Control) learning values are cleared. This DTC cannot be set with the ISC learning values cleared.


HINT:

The ISC learning is performed when the engine is warmed up and has been idling for 5 minutes.


A153342E52
2.51,3.188 1.948,4.125 1.948,4.125 1.771,4.125 false 4.625,2.438 4.906,2.76 4.906,2.76 5.083,2.76 false 4.635,1.99 5.063,1.323 5.063,1.323 5.302,1.323 false 1.438,0.813 2.354,0.99 0.917,0.177 10 false Ignition Timing 1.542,1.208 2.177,1.385 0.635,0.177 10 false Advanced 1.594,3.052 2.177,3.229 0.583,0.177 10 false Retarded 1.542,2.063 2.177,2.24 0.635,0.177 10 false Threshold 0.979,4.042 1.76,4.219 0.781,0.177 10 false Engine Start 2.698,3.385 2.854,3.563 0.156,0.177 10 false 3 3.75,3.385 3.917,3.563 0.167,0.177 10 false 10 3.573,3.667 3.896,3.844 0.323,0.177 10 false Time 4.813,3.354 5.458,3.531 0.646,0.177 10 false (Seconds) 5.146,2.656 6.688,2.833 1.542,0.177 10 false Pass Condition Detected 3.708,1.594 4.323,1.771 0.615,0.177 10 false 8 or more 5.365,1.229 6.396,1.406 1.031,0.177 10 false P050B Detected 0.479,0.292 2.521,0.563 2.042,0.271 12 false P050B Detection Logic: 2.573,4.135 6,4.313 3.427,0.177 10 false Engine Coolant Temperature: -10 to 50°C (14 to 122°F)

DTC Code DTC Detection Condition Trouble Area
P050B Insufficient ignition timing retard at cold start (2-trip detection logic)
·

Throttle body assembly

·

Mass air flow meter

·

PCV system

·

Air cleaner filter element sub-assembly

·

Air induction system

·

VVT system

·

ECM

·

Wire harness or connector



MONITOR STRATEGY

Related DTCs P050B: Cold start ignition timing performance
Required Sensors/Components (Main) Throttle body assembly
Required Sensors/Components (Related) Mass air flow meter
Engine Coolant Temperature (ECT) sensor
Frequency of Operation Once per driving cycle
Duration 10 seconds
MIL Operation 2 driving cycles
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever following DTCs not present P0010, P0020 (VVT Oil control valve)
P0011, P0021 (VVT System - Advance)
P0012, P0022 (VVT System - Retard)
P0013, P0023 (Exhaust VVT Oil control valve)
P0014, P0024 (Exhaust VVT System - Advance)
P0015, P0025 (Exhaust VVT System - Retard)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0171, P0172, P0174, P0175 (Fuel system)
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2, P21A3 (Air-fuel ratio imbalance)
P0301 - P0308 (Misfire)
P0335 (Crankshaft position sensor)
P1340 (Camshaft position sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor)
P0351 - P0358 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor)
P0500 (Vehicle speed sensor)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor)
P0705 (Shift lever position switch)
Battery voltage 8 V or more
Time after engine start 3 seconds or more
Starter OFF
ECT at engine start -10°C (14°F) or more
ECT -10 to 50°C (14 to 122°F)
Engine idling time 3 seconds or more
Fuel-cut OFF
Vehicle speed Less than 3 km/h (1.875 mph)
Atmospheric pressure 76 kPa (570 mmHg) or more

TYPICAL MALFUNCTION THRESHOLDS

Accumulated time when ignition timing retard is cut off 8 seconds or more

CONFIRMATION DRIVING PATTERN

1.

Connect the Techstream to the DLC3.

2.

Turn the ignition switch to ON and turn the Techstream on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the Techstream on.

6.

Enter the following menu items: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

7.

Check that "Coolant Temp" in the Data List is within the range of -10 to 50°C.

8.

Start the engine and warm it up until the coolant temperature is the same as the coolant temperature in the freeze frame data.

9.

Idle the engine for 1 minute or more [A].

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

11.

Read the Pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P050B.

14.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 3 minutes, let the engine cool down, and then perform steps [A] through [B].



15.

If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

DTC P050B may be set when the engine has the symptoms listed below. If necessary, check the trouble areas listed below.

Symptoms Factor Trouble Area
Low idle speed when engine is cold (immediately after engine start) Excessive engine friction
·

Engine oil deterioration

·

Drive belt tension

·

A/C compressor

·

Generator

·

Vane pump


Rough idle when engine is cold (immediately after engine start) Abnormal combustion Fuel quality

·

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050B)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Display (DTC Output) Proceed to
P050B A
P050B and other DTCs B

HINT:

If any DTCs other than P050B are output, troubleshoot those DTCs first.




OK

2.READ VALUE USING TECHSTREAM (FUEL TRIM)

NG

2.READ VALUE USING TECHSTREAM (FUEL TRIM)
HINT:

Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/F Control System / Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2.


e.

Read the values displayed on the Techstream.


f.

Add together the Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values to obtain the total fuel trim.

OK:

Total of Short FT #1 and Long FT #1, or Short FT #2 and Long FT #2 values is between -20% and 20%.




OK

3.INSPECT THROTTLE BODY ASSEMBLY

NG

5.CHECK PCV SYSTEM
3.INSPECT THROTTLE BODY ASSEMBLY
a.

Check that there are no deposits around the throttle valve.

OK:

No deposits around the throttle valve.




OK

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)

NG

4.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY
4.REPAIR OR REPLACE THROTTLE BODY ASSEMBLY
a.

Repair or replace the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>THROTTLE BODY>REMOVAL).

HINT:

Perform "Inspection After Repair" after repairing or replacing the throttle body assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
5.CHECK PCV SYSTEM
a.

Start the engine.


b.

Pinch the positive crankcase ventilation hose.


c.

Check the engine rpm.

OK:

The engine rpm rises when the PCV hose is pinched.




OK

6.CHECK AIR INDUCTION SYSTEM

NG

10.REPAIR OR REPLACE PCV SYSTEM
6.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leaks (See page Engine / Hybrid System>3UR-FBE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from the air induction system.




OK

7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

11.REPAIR OR REPLACE AIR INDUCTION SYSTEM
7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Visually check that the air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.

OK:

The air cleaner filter element sub-assembly is not excessively contaminated with dirt or oil.




OK

8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OILCONTROL VALVE)

NG

12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
8.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OILCONTROL VALVE)
a.

Operate the VVT system through the Active test, and check if the VVT system is operating normally.

i.

(1) Perform the Active Test, referring to DTC P0011 inspection procedure (VVT system for intake camshaft) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0011).


ii.

Perform the Active Test, referring to DTC P0014 inspection procedure (VVT system for exhaust camshaft) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0014).




OK

9.READ VALUE USING TECHSTREAM (MAF)

NG

13.CHECK AND REPAIR VVT SYSTEM
9.READ VALUE USING TECHSTREAM (MAF)

OK

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)

NG

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
10.REPAIR OR REPLACE PCV SYSTEM
a.

Repair or replace the PCV system.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
11.REPAIR OR REPLACE AIR INDUCTION SYSTEM
a.

Repair or replace the air induction system.

HINT:

Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the air cleaner filter element sub-assembly.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
13.CHECK AND REPAIR VVT SYSTEM
a.

Check and repair the VVT system.

HINT:
·

Refer to DTC P0011 Inspection Procedure (VVT system for intake side) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0011).

·

Refer to DTC P0014 Inspection Procedure (VVT system for exhaust side) (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0014).





NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
NOTICE:

For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


h.

Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P050B.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050B is output) B



A

B

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
NOTICE:

For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


h.

Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P050B.


m.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P050B is output) A
NORMAL (DTC is not output) B



A

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

18.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the result of the inspection performed in step 9 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).





NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
19.CHECK WHETHER DTC OUTPUT RECURS (DTC P050B)
NOTICE:

For this operation, the engine must be cold (the same level as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the Techstream on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.


h.

Check that the engine coolant temperature is between - 10°C and 50°C (14 and 122°F).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P050B.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050B is output) B



A

END

B