Refer to DTC P0300 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P0300).
Refer to DTC P2195 (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>P2195).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P219A | The difference in air-fuel ratios between the cylinders exceeds the threshold. | ·
Fuel injector assembly ·
Air induction system ·
Gas leak from exhaust system ·
Ignition system ·
Compression pressure ·
Air fuel ratio sensor ·
ECM |
| P219B | The difference in air-fuel ratios between the cylinders exceeds the threshold. | |
| P219C | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | |
| P219D | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | |
| P219E | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | |
| P219F | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | |
| P21A0 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | |
| P21A1 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | |
| P21A2 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). | |
| P21A3 | The difference in air fuel ratios between the cylinders exceeds the threshold (2 trip detection logic). |
The ECM uses the air fuel ratio sensor and crankshaft position sensor to monitor the difference in air-fuel ratios between the cylinders caused by differences in injection volumes between the cylinders, leakage in the intake or exhaust system, etc.
When the air-fuel ratios of the cylinders are lean or rich with respect to each other, the ECM determines that a problem is present and stores a DTC.
When the system detects a difference in air-fuel ratios between the cylinders due to fluctuation in the air fuel ratio sensor output over 1 engine cycle (2 crankshaft revolutions), the system determines that there is a problem.
The system monitors the engine speed variation and when the variation becomes large, the system determines that there is a difference in air-fuel ratios between the cylinders, which it determines to be a problem.
| Related DTCs | P219A: Air fuel ratio cylinder imbalance monitor (Bank 1)
P219B: Air fuel ratio cylinder imbalance monitor (Bank 2) P219C: Air fuel ratio cylinder imbalance monitor (Cylinder 1) P219D: Air fuel ratio cylinder imbalance monitor (Cylinder 2) P219E: Air fuel ratio cylinder imbalance monitor (Cylinder 3) P219F: Air fuel ratio cylinder imbalance monitor (Cylinder 4) P21A0: Air fuel ratio cylinder imbalance monitor (Cylinder 5) P21A1: Air fuel ratio cylinder imbalance monitor (Cylinder 6) P21A2: Air fuel ratio cylinder imbalance monitor (Cylinder 7) P21A3: Air fuel ratio cylinder imbalance monitor (Cylinder 8) |
| Required Sensors/Components (Main) | Air fuel ratio sensor
Crankshaft position sensor |
| Required Sensors/Components (Related) | Mass air flow meter assembly
Engine coolant temperature sensor Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 seconds: Air fuel ratio sensor monitoring method
30 seconds: Crankshaft position sensor monitoring method |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0010, P0020 (VVT oil control valve)
P0011, P0021 (VVT system - Advance) P0012, P0022 (VVT system - Retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - Advance) P0015, P0025 (Exhaust VVT system - Retard) P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P1340 (Camshaft position sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary Air Injection System Control) P0500 (Vehicle speed sensor) P2440, P2441, P2442, P2443, P2444, P2445, P2446, P2447 (Secondary Air Injection System) |
| Air fuel ratio sensor status | Activated |
| Engine speed | 1400 to 2200 rpm |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa (570 mmHg) or higher |
| Fuel system status | Closed loop |
| Vehicle speed | Less than 3 km/h (1.875 mph) |
| Engine speed | 400 to 1050 rpm |
| Engine coolant temperature | 75°C (167°F) or higher |
| Air fuel ratio sensor status | Activated |
| Battery voltage | 11 V or higher |
| Fuel system status | Closed loop |
| A/F sensor monitoring method criteria (rich side imbalance) | 0.211 or more |
| A/F sensor monitoring method criteria (rich side imbalance) | 0.27 or more |
| Crankshaft position sensor monitoring method criteria (lean side imbalance) | 1.0 or more |
Refer to detailed information in Checking Monitor Status (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>CHECKING MONITOR STATUS).
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
Drive the vehicle at 60 km/h (38 mph) or higher for 2 minutes or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
It is acceptable to turn electrical loads on while driving.
Idle the engine for 2 minutes or more [C].
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [E].
Accelerate the vehicle from 30 to 60 km/h (19 to 38 mph) over a period of approximately 10 to 20 seconds.
Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 38 mph).
Drive the vehicle at 60 km/h (38 mph) or higher for 5 seconds or more [F].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Drive the vehicle at less than 30 km/h (19 mph) for 5 seconds or more [G].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Accelerate the vehicle from 30 to 60 km/h (19 to 38 mph) over a period of approximately 10 to 20 seconds.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Refer to the values of mass air flow and engine speed in Typical Enabling Conditions before accelerating the vehicle from 30 to 60 km/h (19 to 38 mph).
Drive the vehicle at 60 km/h (38 mph) or more for 5 seconds or more [H].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Repeat steps [G] through [H] above at least 2 times [I].
Idle the engine for 1 minute or more [J].
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [K].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3.
Check the DTC judgment result.
| Techstream Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the following procedure.
If no pending DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
Sensor 1 refers to the sensor closest to the engine assembly.
When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output | A |
| DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 and other DTCs are output | B |
If any DTCs other than DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output, troubleshoot those DTCs first.
A
B
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Using the Techstream, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
Vehicle Speed
Engine Speed
Calculate Load
Accelerator Idle Position
Short FT #1 or #2
Long FT #1 or #2
Cylinder #1 Misfire Count to Cylinder #8 Misfire Count
When the sum of Short FT and Long FT is positive, the engine is running lean, and when the sum is negative, the engine is running rich.
| Air Fuel Ratio Sensor Monitoring Method (P219A and P219B) | Crankshaft Position Sensor Monitoring Method (P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and P21A3) | Note |
|---|---|---|
| DTCs are output | DTC is output (Only one DTC relating to a single cylinder is output) | Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected. |
| DTCs are output | DTCs are output (Multiple DTCs relating to multiple cylinders are output) | Malfunction of cylinders except ones detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected.*1 |
| DTCs are not output | DTCs are output | Malfunction of cylinders detected by the Crankshaft Position Sensor Monitoring Method is primarily suspected. |
| DTCs are output | DTCs are not output | Malfunctioning of the bank detected by the Air Fuel Ratio Sensor Monitoring Method is primarily suspected. |
*1: When any air-fuel ratio imbalance is detected, the ECM will perform air-fuel ratio feedback control to make the air-fuel ratio close to the stoichiometric level. This may result in an air-fuel ratio imbalance of normal cylinders and DTCs may be stored.
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
If any misfire count ("Cylinder #1 Misfire Count" to "Cylinder #8 Misfire Count) increases while idling or driving the vehicle, proceed to step 6.
Perform inspections while focusing on the cylinder whose misfire count has increased.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
| Result | Proceed to |
|---|---|
| DTC P219A or P219B is output | A |
| DTC P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 or P21A3 are output | B |
| DTC P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 are output |
A
B
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
The A/C switch and all accessory switches should be off and the shift lever should be in P or N.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Data List / Cylinder #1 to #8 Misfire Count.
When the "Control the Injection Volume" Active Test is selected (injection volume is 0%), if a misfire count increases, proceed to step 6 (Check Air Induction System).
Perform the Control the Injection Volume operation with the engine idling.
Check the misfire counts ("Cylinder #1 Misfire Count" to "Cylinder #8 Misfire Count") while decreasing the injection volume in 5% increments.
Do not decrease the injection volume by more than 20%.
The cylinder whose misfire count has not increased can be assumed to be running rich. Therefore, perform inspections while focusing on that cylinder.
NEXT
Check for exhaust gas leaks.
No gas leaks.
Perform "Inspection After Repair" after repairing or replacing the exhaust system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Check the air induction system for vacuum leakage (See page Engine / Hybrid System>3UR-FBE INTAKE>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
No leakage in air induction system.
Perform "Inspection After Repair" after repairing or replacing the air induction system (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Inspect the spark plug of the cylinder causing the imbalance (See page Engine / Hybrid System>3UR-FBE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
Perform "Inspection After Repair" after replacing the spark plug (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Perform a spark test (See page Engine / Hybrid System>3UR-FBE IGNITION>IGNITION SYSTEM>ON-VEHICLE INSPECTION).
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
NEXT
Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>3UR-FBE ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION).
Perform "Inspection After Repair" after repairing or replacing the engine assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
Check the fuel injector injection [whether fuel volume is high or low, and whether injection pattern is poor] (See page Engine / Hybrid System>3UR-FBE FUEL>FUEL INJECTOR>INSPECTION).
Perform "Inspection After Repair" after replacing the fuel injector assembly (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).
OK
NG
If the cause of the problem has not been found even after performing the troubleshooting procedure, perform the inspection below.
Check the intake valve for deposits.
As the DTC may have been stored due to deposits on the intake valve, remove the cylinder head and check the intake valve.
NEXT
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Check for DTCs.
P219A, P219B, P219C, P219D, P219E, P219F, P21A0, P21A1, P21A2 and/or P21A3 is not output.
NEXT