Home › Engine / Hybrid System › 3UR-FBE ENGINE CONTROL › AIR FUEL RATIO SENSOR
RM27M0U _51 Engine / Hybrid System _049095 3UR-FBE ENGINE CONTROL _0233938 AIR FUEL RATIO SENSOR A

3UR-FBE ENGINE CONTROL  AIR FUEL RATIO SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 89467B 1.INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

a.
A194685

Install the air fuel ratio sensor to the front exhaust pipe assembly by hand.


b.
A194686E04
1.552,1.434 1.763,1.604 0.211,0.170 10 *a 2.8,1.581 3.188,1.788 0.387,0.207 10 SST 2.568,1.006 2.968,1.386 2.968,1.386 2.968,1.557 false

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

Text in Illustration
*a Fulcrum length

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.

·

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




Hide 89467B 2.INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

a.
A194685

Install the air fuel ratio sensor to the front No. 2 exhaust pipe assembly by hand.


b.
A194686E05
1.584,1.492 1.761,1.661 0.177,0.169 10 *a 2.8,1.581 3.188,1.788 0.387,0.207 10 SST 2.568,1.006 2.968,1.386 2.968,1.386 2.968,1.557 false

Using SST, tighten the air fuel ratio sensor.

SST
09224-00010  

Torque:
without SST : 44 N*m (449 kgf*cm, 32 ft.*lbf)
with SST : 40 N*m (408 kgf*cm, 30 ft.*lbf)

Text in Illustration
*a Fulcrum length

HINT:
·

Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Make sure SST and the wrench are connected in a straight line.

·

Perform "Inspection After Repairs" after replacing the air fuel ratio sensor (See page Engine / Hybrid System>3UR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket and the front exhaust pipe assembly to the exhaust manifold RH with 3 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


b.

Install a new gasket and the front exhaust pipe assembly to the center exhaust pipe with the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


c.

Connect the air fuel ratio sensor connector.


d.

Attach the 2 clamps and connect the heated oxygen sensor connector.


Hide 17450B 4.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

a.

Connect the front No. 2 exhaust pipe assembly to the exhaust pipe support.


b.

Install a new gasket and the front No. 2 exhaust pipe assembly to the exhaust manifold LH with 3 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


c.

Install a new gasket and the front No. 2 exhaust pipe assembly to the center exhaust pipe assembly with the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


d.

Connect the air fuel ratio sensor connector.


e.

Connect the heated oxygen sensor connector.


Hide 37140 5.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 37117 6.INSTALL PROPELLER SHAFT HEAT INSULATOR