1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
4.DRAIN ENGINE OIL
5.DRAIN ENGINE COOLANT
16400
6.REMOVE RADIATOR ASSEMBLY
17880
7.REMOVE AIR CLEANER HOSE ASSEMBLY
8.REMOVE AIR CLEANER ASSEMBLY
9.DISCONNECT ENGINE WIRE
Engine Room LH Side:
Remove the engine room relay block cover.
Disconnect the 2 connectors and detach the 2 clamps from the engine room junction block.
Disconnect the 4 air injection control driver connectors.
Disconnect the 2 wire harness clamps.
Disconnect the injector connector.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the 5 clamps.
Remove the 2 bolts and ground wire LH.
Disconnect the engine coolant temperature sensor connector.
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the camshaft position sensor connector.
Disconnect the 3 clamps.
Disconnect the cooler compressor connector.
Engine Room RH Side:
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the injector connector.
Disconnect the 2 VVT sensor connectors.
Remove the 2 bolts and ground wire RH.
Disconnect the 2 air pump connectors.
Disconnect the throttle position sensor and throttle control motor connector.
Disconnect the 7 clamps.
Disconnect the 2 clamps and power steering oil pressure switch connector.
| *1 | Junction Connector |
for 4WD:
Disconnect the clamp and junction connector.
17111
10.REMOVE INTAKE MANIFOLD
11.DISCONNECT AIR PUMP HOSE AND WIRE HARNESS
Slide the 2 clamps and disconnect the No. 2 air hose and No. 3 air hose from the air tube sub-assembly.
| *1 | No. 3 Air Hose |
| *2 | No. 2 Air Hose |
Disconnect the 2 clamps.
12.DISCONNECT HEATER HOSE AND PIPE
Remove the 2 bolts.
Slide the 3 clamps and disconnect the 3 hoses.
88320
13.DISCONNECT COOLER COMPRESSOR ASSEMBLY
Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.
It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.
23902
14.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the No. 2 fuel tube sub-assembly.
| *a | LH Side |
| *b | RH Side |
15.REMOVE OIL FILTER ELEMENT
83520
16.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY
16268A
17.REMOVE NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)
Slide the 4 clamps and disconnect the 4 hoses from the No. 2 water by-pass pipe.
Remove the 3 bolts and No. 2 water by-pass pipe.
15781
18.REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)
15671
19.REMOVE OIL FILTER BRACKET (w/ Oil Cooler)
20.REMOVE OIL FILTER BRACKET (w/o Oil Cooler)
Remove the 2 bolts, 2 nuts and oil filter bracket.
Remove the 2 O-rings.
11452
21.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
44320
22.DISCONNECT VANE PUMP ASSEMBLY
Remove the 2 bolts and disconnect the vane pump assembly.
27020
23.REMOVE GENERATOR ASSEMBLY
Disconnect the generator connector.
Remove the terminal cap and nut, and disconnect the generator wire.
Remove the bolt and disconnect the wire harness bracket from the generator assembly.
Remove the 2 bolts, 2 nuts and generator assembly.
Remove the 2 stud bolts.
16261G
24.REMOVE NO. 1 WATER BY-PASS HOSE
Slide the 2 clamps and remove the No. 1 water by-pass hose from the water inlet housing and front water by-pass joint.
16206
25.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the bolt and disconnect the air tube sub-assembly.
Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.
Remove the 2 bolts and water by-pass pipe sub-assembly.
16297
26.DISCONNECT NO. 9 WATER BY-PASS HOSE
Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.
| *1 | No. 9 Water By-pass Hose |
| *2 | No. 10 Water By-pass Hose |
16293
27.DISCONNECT NO. 10 WATER BY-PASS HOSE
Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.
16355
28.REMOVE FRONT WATER BY-PASS JOINT
Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.
Remove the 4 nuts, front water by-pass joint and 2 gaskets.
11212
29.REMOVE NO. 2 ENGINE COVER
12611
30.REMOVE NO. 1 ENGINE COVER
17303
31.REMOVE AIR TUBE SUB-ASSEMBLY
Remove the bolt, disconnect the 2 hoses, and remove the air tube sub-assembly.
16323
32.REMOVE WATER INLET HOUSING
Remove the 3 bolts, water inlet housing and gasket.
16173
33.REMOVE WATER PUMP PULLEY
Using SST, hold the water pump pulley.
| *a | SST |
Remove the 4 bolts and water pump pulley.
16603
34.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and No. 1 idler pulley sub-assembly.
16211
35.REMOVE FAN BRACKET ASSEMBLY
Remove the 4 bolts and fan bracket assembly.
16620
36.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the standard bolt, 6 mm hexagon wrench bolt and V-ribbed belt tensioner assembly.
19500
37.REMOVE IGNITION COIL ASSEMBLY
Remove the 8 bolts and 8 ignition coils.
11202
38.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 5 gaskets from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.
11201
39.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 5 gaskets from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.
13471
40.REMOVE CRANKSHAFT PULLEY
Using SST, loosen the crankshaft pulley set bolt.
| *a | SST |
| *b | Turn |
| *c | Hold |
Partially install the crankshaft pulley set bolt to the crankshaft pulley until 2 or 3 threads are engaged.
Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley.
| *a | SST |
| *b | Turn |
| *c | Hold |
41.DISCONNECT WIRE HARNESS CLAMP BRACKET
Remove the bolt and disconnect the wire harness clamp bracket.
11302
42.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 28 bolts and nut shown in the illustration.
| *1 | Nut |
Remove the timing chain cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.
Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain cover sub-assembly.
Tape the screwdriver tip before use.
Remove the oil pump gasket from the cylinder block.
Remove the O-ring from the oil pan sub-assembly.
16322
43.REMOVE WATER INLET PIPE
Remove the water inlet pipe from the No. 1 heat exchanger cover.
Remove the 2 O-rings from the water inlet pipe.