Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › CAMSHAFT(for Bank 2) › 2015.08–2016.08
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234035 CAMSHAFT(for Bank 2) A

1UR-FE ENGINE MECHANICAL  CAMSHAFT(for Bank 2)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the No. 1 or No. 2 camshaft sub-assembly or camshaft timing gear RH or camshaft timing exhaust gear RH (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.INSTALL CAMSHAFT BEARING CAP RH

HINT:

Perform "Inspection After Repairs" after replacing the No. 1 or No. 2 camshaft sub-assembly (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A160686E07
1.708,0.135 1.906,0.354 0.198,0.219 9 false R3 1.75,1.938 1.927,2.156 0.177,0.219 9 false R2 0.719,1.938 0.917,2.146 0.198,0.208 9 false R4 1.219,1.927 1.385,2.135 0.167,0.208 9 false R3 0.146,1.927 0.313,2.146 0.167,0.219 9 false R5

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.

Install the No. 1 and No. 2 camshafts to the camshaft housing.


c.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
A160687E04
2.792,1.708 2.906,1.875 0.115,0.167 10 true 1 2.823,0.208 2.938,0.375 0.115,0.167 10 true 2 2.104,1.719 2.219,1.885 0.115,0.167 10 true 3 2.104,0.24 2.219,0.406 0.115,0.167 10 false 4 1.552,1.719 1.667,1.885 0.115,0.167 10 true 5 1.552,0.208 1.667,0.375 0.115,0.167 10 false 6 1.01,1.719 1.125,1.885 0.115,0.167 10 true 7 1,0.219 1.115,0.385 0.115,0.167 10 false 8 0.354,1.719 0.469,1.885 0.115,0.167 10 true 9 0.313,0.229 0.5,0.396 0.188,0.167 10 false 10

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11103C 2.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

U151458E02
1.479,0.625 1.76,0.76 1.76,0.76 1.885,0.76 false 1.281,1.646 1.698,1.646 false 1.906,0.125 3.115,0.333 1.208,0.208 10 false Valve Rocker Arm 1.938,0.698 2.979,0.938 1.042,0.24 10 false Valve Stem Cap 1.75,1.552 3.021,1.74 1.271,0.188 10 false Valve Lash Adjuster

a.

Make sure that the valve rocker arms are installed as shown in the illustration.


b.
A380007E01
0.729,1.708 2.625,1.927 1.896,0.219 10 false Seal diameter: 3.5 to 4.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A163556E06
0.865,2.625 1.698,2.938 1.698,2.938 2.25,2.729 false 1.479,1.323 1.573,1.479 0.094,0.156 10 true 1 0.854,1.323 0.948,1.479 0.094,0.156 10 true 2 1.979,1.313 2.073,1.469 0.094,0.156 10 true 3 0.219,1.344 0.313,1.5 0.094,0.156 10 true 4 2.625,1.313 2.719,1.469 0.094,0.156 10 true 5 1.427,1.896 1.521,2.052 0.094,0.156 10 false 6 1.365,0 1.458,0.156 0.094,0.156 10 false 7 0.875,1.885 0.969,2.042 0.094,0.156 10 false 8 0.844,0 0.938,0.156 0.094,0.156 10 false 9 1.948,1.896 2.135,2.052 0.188,0.156 10 false 10 1.917,0 2.104,0.156 0.188,0.156 10 false 11 0.177,1.896 0.365,2.052 0.188,0.156 10 false 12 0.188,0 0.375,0.156 0.188,0.156 10 false 13 3.042,1.313 3.229,1.469 0.188,0.156 10 false 14 2.49,0.063 2.677,0.219 0.188,0.156 10 false 15 3.115,0 3.302,0.156 0.188,0.156 10 false 17 2.333,1.677 2.521,1.833 0.188,0.156 10 true 18 0.021,0.406 0.208,0.563 0.188,0.156 10 true 16 1.323,2.958 2.021,3.125 0.698,0.167 10 false Knock Pin 0.573,2.125 0.948,2.323 0.375,0.198 10 false 55° 2,2.219 2.375,2.417 0.375,0.198 10 false 70° 1.281,2.146 1.531,2.344 0.25,0.198 10 false EX 2.667,2.125 2.917,2.323 0.25,0.198 10 false IN 2.802,1.875 2.927,2.042 0.125,0.167 10 false A

Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pin of the camshaft is positioned as shown in the illustration before installing the camshaft housing.




d.
A160684E08
2.823,1.646 2.938,1.802 0.115,0.156 10 true 1 2.802,0.198 2.917,0.354 0.115,0.156 10 true 2 2.125,1.646 2.24,1.802 0.115,0.156 10 true 3 2.104,0.219 2.219,0.375 0.115,0.156 10 true 4 1.563,1.646 1.677,1.802 0.115,0.156 10 true 5 1.552,0.208 1.667,0.365 0.115,0.156 10 false 6 0.99,1.646 1.104,1.802 0.115,0.156 10 true 7 0.969,0.188 1.083,0.344 0.115,0.156 10 false 8 0.365,1.646 0.479,1.802 0.115,0.156 10 true 9 0.313,0.198 0.5,0.354 0.188,0.156 10 false 10

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 13550 3.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A214843E04
1.594,2.969 1.74,2.969 1.74,2.969 1.906,2.625 false 1.604,2.458 2.365,2.313 2.365,2.313 2.552,2.313 true 2.333,0.75 2.688,0.938 0.354,0.188 10 true Push 1.313,2.896 1.563,3.073 0.25,0.177 10 false Pin 2.604,2.219 3.177,2.448 0.573,0.229 10 false Plunger

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


Hide 13506 4.INSTALL NO. 1 CHAIN SUB-ASSEMBLY RH

HINT:

Perform "Inspection After Repairs" after replacing the No. 1 or No. 2 camshaft sub-assembly or camshaft timing gear RH or camshaft timing exhaust gear RH (See page Engine / Hybrid System>1UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.
A160662E06
2.448,0.708 2.448,1.302 false 2.375,0.198 2.375,0.625 true 1.938,0.198 2.604,0.198 2.604,0.198 2.604,0.656 true 0.469,0.094 1.677,0.281 1.208,0.188 10 false Orange Mark Plate 2.021,1.313 2.833,1.479 0.813,0.167 10 true Timing Mark

Align the No. 1 chain's orange mark plates with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


b.
A149461E08
2.438,1.313 1.958,1.865 true 1.896,1.771 1.125,1.604 true 0.271,1.521 1.063,1.698 0.792,0.177 10 false Timing Mark 2.5,1.219 3.219,1.542 0.719,0.323 10 false Orange Mark Plate

Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


c.
A160663E07
0.854,1.094 1.979,1.865 1.979,1.865 2.75,1.094 true 0.875,0.75 1.188,0.135 1.188,0.135 1.323,0.135 true 2.365,0.146 2.51,0.146 2.51,0.146 2.719,0.813 true 1.292,1.875 2.427,2.042 1.135,0.167 10 false Yellow Mark Plate 1.469,0.063 2.323,0.26 0.854,0.198 10 false Timing Mark

Align the No. 2 chain's yellow mark plates with the timing marks of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.

HINT:

The crankshaft timing gear and camshaft exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket to the crankshaft.


e.

Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.


f.

Using the hexagonal portion of the No. 2 camshaft, align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear.


g.

Remove the pin from the No. 2 chain tensioner.


Hide 13561 5.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH

a.
A214617

Install the vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13559 6.INSTALL NO. 1 CHAIN TENSIONER SLIPPER RH

A214616

HINT:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and then install the chain tensioner slipper.


Hide 13540 7.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH

a.
A148260E01
2.712,1.388 3.255,1.572 0.543,0.184 10 Plunger 0.1,0.606 0.973,0.794 0.873,0.188 10 Stopper Plate 2.425,1.1 2.682,1.467 2.682,1.467 1.951,1.72 false 1.996,0.979 1.174,0.693 1.174,0.693 1.361,1.403 false

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.
A214615

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the chain tensioner.


Hide 13050 12.TIGHTEN CAMSHAFT TIMING GEAR

a.

LH:

i.
A214802E04
2.885,0.365 3.208,0.542 0.323,0.177 10 true Hold 0.74,0.115 1.083,0.302 0.344,0.188 10 false Turn

Using a wrench to hold the hexagonal portion of the No. 3 camshaft, tighten the camshaft timing gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


ii.
A214803E04
0.875,0.208 1.208,0.417 0.333,0.208 10 true Turn 3,0.75 3.323,0.896 0.323,0.146 10 false Hold

Using a wrench to hold the hexagonal portion of the No. 4 camshaft, tighten the camshaft timing exhaust gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)



b.

RH:

i.
A214804E02
2.667,0.458 3.021,0.823 0.354,0.365 10 true Turn 1.198,0.042 1.552,0.25 0.354,0.208 10 false Hold

Using a wrench to hold the hexagonal portion of the No. 1 camshaft, tighten the camshaft timing gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


ii.
A214805E02
2.396,0.99 2.74,1.323 0.344,0.333 10 true Turn 0.771,0.094 1.104,0.281 0.333,0.188 10 false Hold

Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the camshaft timing exhaust gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)



Hide 13.CHECK NO. 1 CYLINDER TO TDC / COMPRESSION

Hide 11302 14.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Install the timing chain cover (See page Engine / Hybrid System>1UR-FE LUBRICATION>OIL PUMP>INSTALLATION).