Home › Engine / Hybrid System › 1UR-FE ENGINE MECHANICAL › CAMSHAFT(for Bank 2)
RM27M0U _51 Engine / Hybrid System _049107 1UR-FE ENGINE MECHANICAL _0234035 CAMSHAFT(for Bank 2) A

1UR-FE ENGINE MECHANICAL  CAMSHAFT(for Bank 2)  REMOVAL  


PROCEDURE

Hide 11302 1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.

Remove the timing chain cover (See page Engine / Hybrid System>1UR-FE LUBRICATION>OIL PUMP>REMOVAL).


Hide 13540 3.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH

Hide 13540 7.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH

a.
A214613E04
1.948,0.917 2.167,1.635 2.167,1.635 2.26,1.635 true 1.99,0.771 2.51,0.771 true 2.292,1.552 3.24,1.99 0.948,0.438 10 true Stopper Plate 2.542,0.688 3.146,0.938 0.604,0.25 10 true Plunger

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.
A214614E04
1.938,0.958 2.146,1.708 2.146,1.708 2.271,1.708 true 1.99,0.75 2.615,0.75 true 2.333,1.625 3.229,1.844 0.896,0.219 10 true Stopper Plate 2.646,0.667 3.167,0.885 0.521,0.219 10 true Plunger

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.


c.
A214615

Remove the 2 bolts and chain tensioner.


Hide 13559 8.REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH

A214616

Hide 13561 9.REMOVE NO. 1 CHAIN VIBRATION DAMPER RH

A214617

a.

Remove the 2 bolts and vibration damper.


Hide 13506 10.REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH

A214618E05
1.323,2.625 1.385,2.323 1.385,2.323 1.479,2.323 false 1.042,2.74 1.042,2.927 false 1.531,2.25 1.781,2.427 0.25,0.177 10 false Pin 0.76,2.938 1.313,3.135 0.552,0.198 10 false Plunger 2.104,0.719 2.51,1.031 0.406,0.313 10 true Push

a.

While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


b.
A214619E01
2.342,0.031 2.717,0.217 0.375,0.186 10 Turn 1.174,0 1.487,0.170 0.313,0.170 10 Hold

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:
·

Be careful not to damage the cylinder head with the wrench.

·

Do not disassemble the camshaft timing gear.




c.
A214620E04
0.281,0.865 0.625,1.052 0.344,0.188 10 false Hold 1.406,0.76 1.76,0.948 0.354,0.188 10 true Turn

Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.

NOTICE:

Be careful not to damage the cylinder head with the wrench.



d.

Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.


e.

Remove the No. 1 and No. 2 chains from the gears.


Hide 13550 11.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

A214621

a.

Remove the 2 bolts and chain tensioner.


Hide 12.REMOVE CAMSHAFT BEARING CAP RH

A214625E03
0.677,2.563 1.552,2.844 1.552,2.844 2.094,2.656 false 0.438,2.073 0.76,2.25 0.323,0.177 10 false 55° 1.865,2.104 2.188,2.281 0.323,0.177 10 false 70° 1.177,2.865 1.854,3.052 0.677,0.188 10 false Knock Pin 2.552,2.115 2.75,2.271 0.198,0.156 10 false IN 1.083,2.063 1.354,2.26 0.271,0.198 10 false EX

a.

Make sure that the knock pin of the camshaft is positioned as shown in the illustration.


b.
A160684E07
0.365,0.188 0.479,0.344 0.115,0.156 10 false 1 0.365,1.646 0.479,1.802 0.115,0.156 10 true 2 0.958,0.208 1.073,0.365 0.115,0.156 10 true 3 1,1.625 1.115,1.781 0.115,0.156 10 true 4 1.542,0.208 1.656,0.365 0.115,0.156 10 false 5 1.552,1.646 1.667,1.802 0.115,0.156 10 true 6 2.115,0.229 2.229,0.385 0.115,0.156 10 true 7 2.125,1.656 2.24,1.813 0.115,0.156 10 true 8 2.802,0.198 2.917,0.354 0.115,0.156 10 true 9 2.771,1.646 2.958,1.802 0.188,0.156 10 true 10

Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.
A160685E05
3.24,1.76 3.333,1.917 0.094,0.156 10 false 1 3.208,0.073 3.302,0.229 0.094,0.156 10 false 2 0.146,0.5 0.24,0.656 0.094,0.156 10 true 3 2.604,0.125 2.698,0.281 0.094,0.156 10 false 4 3.156,1.531 3.25,1.688 0.094,0.156 10 false 5 0.302,0.063 0.396,0.219 0.094,0.156 10 false 6 0.302,1.948 0.396,2.104 0.094,0.156 10 false 7 2.021,0.063 2.115,0.219 0.094,0.156 10 false 8 2.063,1.938 2.156,2.094 0.094,0.156 10 false 9 0.875,0.052 1.063,0.208 0.188,0.156 10 false 10 0.896,1.938 1.083,2.094 0.188,0.156 10 false 11 1.375,0.073 1.563,0.229 0.188,0.156 10 false 12 1.448,1.938 1.635,2.094 0.188,0.156 10 false 13 2.646,1.375 2.833,1.531 0.188,0.156 10 true 14 0.25,1.365 0.438,1.521 0.188,0.156 10 true 15 0.885,1.375 1.073,1.531 0.188,0.156 10 true 17 1.5,1.375 1.688,1.531 0.188,0.156 10 true 18 1.99,1.365 2.177,1.521 0.188,0.156 10 true 16

Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bolts while keeping the camshaft level.



d.

Remove the 6 bearing caps.

HINT:

Arrange the removed parts in the correct order.



e.

Remove the No. 1 and No. 2 camshafts.


Hide 11103C 13.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

A214626

a.

Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.