Home › Engine / Hybrid System › 1UR-FE LUBRICATION › OIL PUMP
RM27M0U _51 Engine / Hybrid System _049115 1UR-FE LUBRICATION _0234076 OIL PUMP A

1UR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 16400 6.REMOVE RADIATOR ASSEMBLY

Hide 17111 7.REMOVE INTAKE MANIFOLD

Hide 25710 8.REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 1)

Hide 25710 10.REMOVE AIR SWITCHING VALVE ASSEMBLY (for Bank 2)

Hide 11.DISCONNECT ENGINE WIRE

a.

Engine Room LH Side:

i.

Remove the engine room relay block cover.


ii.
A162560

Disconnect the 2 connectors and detach the 2 clamps from the engine room junction block.


iii.
A153551

Disconnect the 4 air injection control driver connectors.


iv.
A210007

Disconnect the 2 wire harness clamps.


v.
A210008

Disconnect the injector connector.


vi.

Disconnect the 4 ignition coil connectors.


vii.

Disconnect the 2 VVT sensor connectors.


viii.

Remove the bolt and ground wire LH.


ix.

Disconnect the noise filter connector.


x.

Disconnect the engine coolant temperature sensor connector.


xi.

Disconnect the 2 camshaft timing oil control valve connectors.


xii.

Disconnect the camshaft position sensor connector.


xiii.

Disconnect the 6 clamps.


xiv.

Disconnect the cooler compressor connector.



b.
A210009

Engine Room RH Side:

i.

Disconnect the 2 camshaft timing oil control valve connectors.


ii.

Disconnect the 4 ignition coil connectors.


iii.

Disconnect the injector connector.


iv.

Disconnect the 2 VVT sensor connectors.


v.

Disconnect the noise filter connector.


vi.

Remove the bolt and ground wire RH.


vii.

Disconnect the 2 air pump connectors.


viii.

Disconnect the 9 clamps.


ix.

Disconnect the power steering oil pressure switch connector and solenoid valve connector.


x.

for 4WD:

Disconnect the clamp and junction connector.



c.
A210025

Remove the bolt and disconnect the wire harness clamp bracket from the timing chain cover sub-assembly.


Hide 17343 12.DISCONNECT NO. 3 AIR INJECTION SYSTEM HOSE

a.
A217522

Slide the clamp and disconnect the No. 3 air injection system hose from the air tube sub-assembly RH.


Hide 13.DISCONNECT HEATER HOSE AND NO. 1 WATER BY-PASS PIPE

a.
A210011

Slide the clamp and disconnect the heater hose from the water by-pass pipe sub-assembly.


b.

Remove the 2 bolts and disconnect the No. 1 water by-pass pipe from the cylinder head cover sub-assembly RH.


Hide 88320 14.DISCONNECT COOLER COMPRESSOR ASSEMBLY

a.
A163332

Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.

HINT:

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 83520 16.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 15671 17.REMOVE OIL FILTER BRACKET

a.
A214841

Remove the 2 bolts, 2 nuts and oil filter bracket from the timing chain cover sub-assembly.


b.
A162470

Remove the 2 O-rings.


Hide 11452 18.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 44320 19.DISCONNECT VANE PUMP ASSEMBLY

a.
A163289

Remove the 2 bolts and disconnect the vane pump assembly.


Hide 16261G 23.REMOVE NO. 1 WATER BY-PASS HOSE

Hide 24.REMOVE AIR TUBE SUB-ASSEMBLY RH

a.
A210014

Remove the 2 bolts and air tube sub-assembly RH from the cylinder head cover sub-assembly RH.


Hide 16206 25.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A210015

Slide the clamp and disconnect the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.


b.

Remove the 2 bolts and water by-pass pipe sub-assembly from the cylinder head cover sub-assembly RH.


Hide 16296 26.DISCONNECT NO. 8 WATER BY-PASS HOSE

Hide 16281F 27.DISCONNECT NO. 5 WATER BY-PASS HOSE

Hide 16323 28.REMOVE WATER INLET HOUSING

a.
A210016

Remove the 3 bolts, water inlet housing and gasket from the timing chain cover sub-assembly.


Hide 16297 29.DISCONNECT NO. 9 WATER BY-PASS HOSE

a.
A308525E03
1.198,0.323 1.313,0.323 1.313,0.323 1.51,0.573 true 0.656,1.177 0.823,1.177 0.823,1.177 1.333,1.594 true 0.438,1.083 0.615,1.281 0.177,0.198 10 true *1 1,0.25 1.188,0.448 0.188,0.198 10 true *2

Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose


Hide 16293 30.DISCONNECT NO. 10 WATER BY-PASS HOSE

a.

Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.


Hide 16355 31.REMOVE FRONT WATER BY-PASS JOINT

a.
A308524

Slide the clamp and remove the No. 2 water by-pass hose from the front water by-pass joint.


b.

Remove the 4 nuts, front water by-pass joint and 2 gaskets from the cylinder head.


Hide 16279 32.REMOVE NO. 3 WATER BY-PASS PIPE

A308526

HINT:

Perform this procedure only when replacement of the No. 3 water by-pass pipe is necessary.


a.

Remove the bolt and No. 3 water by-pass pipe from the front water by-pass joint.


Hide 16603 34.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A210019

Remove the bolt and No. 1 idler pulley sub-assembly from the timing chain cover sub-assembly.


Hide 16211 35.REMOVE FAN BRACKET ASSEMBLY

a.
A210020

Remove the 5 bolts and fan bracket assembly from the timing chain cover sub-assembly.


Hide 16620 36.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A162527

Remove the bolt, 6 mm hexagon bolt and V-ribbed belt tensioner assembly from the timing chain cover sub-assembly.


Hide 17364A 37.DISCONNECT NO. 4 AIR TUBE

a.
A214880

Remove the bolt and wire harness clamp bracket from the cylinder head cover sub-assembly LH.


b.
A214844

Remove the bolt and 2 nuts, and disconnect the No. 4 air tube.


c.

Remove the gasket from the No. 4 air tube.

NOTICE:

Be careful not to damage the installation surface of the gaskets.



Hide 17363Q 38.DISCONNECT NO. 3 AIR TUBE

a.
A214881

Remove the bolt and wire harness clamp bracket from the cylinder head cover sub-assembly RH.


b.
A214845

Remove the bolt and 2 nuts, and disconnect the No. 3 air tube.


c.

Remove the gasket from the No. 3 air tube.

NOTICE:

Be careful not to damage the installation surface of the gaskets.



Hide 19500 39.REMOVE IGNITION COIL ASSEMBLY

a.

Remove the 8 bolts and 8 ignition coils.


Hide 11202 40.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A210022

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A162524

Remove the 5 gaskets from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 11201 41.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.
A210024

Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and gasket.

HINT:

Make sure the removed parts are returned to the same places they were removed from.



b.
A162526

Remove the 5 gaskets from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.


Hide 13471 42.REMOVE CRANKSHAFT PULLEY

a.
A164228E07
0.188,0.948 0.188,1.896 false 0.188,1.896 0.354,1.333 false 0.052,1.938 0.375,2.125 0.323,0.188 10 false SST 1.167,2.604 1.51,2.781 0.344,0.177 10 false *a 3.021,1.927 3.198,2.115 0.177,0.188 10 true *b

Using SST, remove the crankshaft pulley set bolt.

SST
09213-70011  
09330-00021  

Text in Illustration
*a Turn
*b Hold


b.

Temporarily install the crankshaft pulley set bolt to the crankshaft pulley until 2 or 3 threads are engaged.


c.
A164229E06
0.458,0.583 0.552,0.583 0.552,0.583 0.646,1.052 true 0.083,0.51 0.396,0.688 0.313,0.177 10 false SST 2.99,2.375 3.188,2.625 0.198,0.25 10 true *b 0.688,2.885 0.885,3.135 0.198,0.25 10 true *c

Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05011)

Text in Illustration
*a Turn
*b Hold


d.

Remove the crankshaft pulley set bolt and SST from the crankshaft pulley.


Hide 11302 43.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A210026E04
1.764,0.526 1.934,0.692 0.171,0.165 10 *1

Remove the 26 bolts and nut shown in the illustration.

Text in Illustration
*1 Nut


b.
A210027

Remove the timing chain cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.

NOTICE:

Be careful not to damage the cylinder head and cylinder block contact surfaces of the timing chain cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A210028

Remove the oil pump gasket from the cylinder block.


d.
A164415

Remove the O-ring from the oil pan sub-assembly.


Hide 16322 44.REMOVE WATER INLET PIPE

a.
A210029

Remove the water inlet pipe from the No. 1 heat exchanger cover.


b.

Remove the 2 O-rings from the water inlet pipe.