Home › Drivetrain › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM
RM27M0U _52 Drivetrain _049120 TIRE AND WHEEL _0234088 TIRE PRESSURE WARNING SYSTEM C

TIRE AND WHEEL  TIRE PRESSURE WARNING SYSTEM  C2174/74  Vehicle Speed Signal Malfunction  C2191/91  Vehicle Speed Signal Error (Test Mode DTC)  


DESCRIPTION

Speed signals are input into the tire pressure warning ECU from the combination meter. At the same time, the G-SW in the tire pressure warning valve and transmitter detects driving conditions, and sends signals to the tire pressure warning ECU. If the speed signal from the combination meter stops and the G-SW signal in the tire pressure warning valve and transmitter indicates that the vehicle is being driven, DTC C2174/74 is stored.

DTC C2191/91 is stored only during the signal check.

DTC Code Detection Condition Trouble Area
C2174/74 Vehicle speed signal malfunction
·

Combination meter

·

Vehicle speed signal circuit

·

Harness or connector

·

Tire pressure warning ECU

·

Tire pressure warning valve and transmitter


C2191/91 Test mode procedure is performed
·

Meter / gauge system (speed signal)

·

Vehicle speed signal circuit

·

Harness or connector

·

Tire pressure warning ECU



WIRING DIAGRAM

C295489E02
5.302,1.313 5.583,1.5 0.281,0.188 10 false J31 5.292,1.49 7.073,1.688 1.781,0.198 10 false Tire Pressure Warning ECU 5.719,0.729 6.042,0.917 0.323,0.188 10 false SPD 5.521,0.635 5.688,0.833 0.167,0.198 10 false 2 1.438,0.635 1.656,0.823 0.219,0.188 10 false 29 1.427,1.25 1.635,1.417 0.208,0.167 10 false 30 1.198,1.25 1.427,1.438 0.229,0.188 10 false SI 1.146,0.635 1.417,0.802 0.271,0.167 10 false +S 0.177,2.073 0.479,2.302 0.302,0.229 10 false J28 0.167,2.24 1.417,2.438 1.25,0.198 10 false Combination Meter 2.958,1.365 3.354,1.573 0.396,0.208 10 false SP1 2.906,2.125 3.219,2.292 0.313,0.167 10 false A17 2.885,2.302 4.073,2.5 1.188,0.198 10 false Skid Control ECU 2.75,1.26 2.906,1.417 0.156,0.156 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.

·

It is necessary to perform initialization (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU after the ECU and/or tire pressure warning valve and transmitter has been replaced.



HINT:

When the speedometer needle is not moving, first troubleshoot the meter/gauge system (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING DATA LIST (VEHICLE SPEED)
a.

Turn the ignition switch off.


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON and the Techstream on.


d.

Enter the following menus: Chassis / Tire Pressure Monitor / Data List.


e.

Check that the values indicated on the Techstream and on the combination meter are the same.

Tire Pressure Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
min.: 0 km/h (0 mph)
max.: 255 km/h (158 mph)
Almost same as actual vehicle speed Speed indicated on combination meter

OK:

Vehicle speed indicated on the Techstream indicates the actual speed.




OK

2.CHECK DTC

NG

3.CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER)
2.CHECK DTC
a.

Perform a driving test.


b.

Check for DTCs.

HINT:

The time required for DTC C2174 to be stored is 20 minutes.


Result
Result Proceed to
DTC C2174 is not output A
DTC C2174 is output B



A

B

6.REPLACE TIRE PRESSURE WARNING ECU
3.CHECK HARNESS AND CONNECTOR (ECU - COMBINATION METER)
a.

Disconnect the J31 tire pressure warning ECU connector.


b.
U152203E02
1.458,1.729 0.99,1.76 true 1.729,3.938 1.906,4.271 true 0.323,0.177 2.719,0.688 2.396,0.51 10 false Front view of wire harness connector: (to Tire Pressure Warning ECU) 0.354,2.51 2.75,3.021 2.396,0.51 10 false Front view of wire harness connector: (to Combination Meter) 0.74,1.188 1.031,1.385 0.292,0.198 10 false J31 0.25,3.698 0.542,3.896 0.292,0.198 10 false J28 0.656,1.677 0.979,1.865 0.323,0.188 10 false SPD 1.865,4.271 2.167,4.438 0.302,0.167 10 false +S

Disconnect the J28 meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J31-2 (SPD) - J28-29 (+S) Always Below 1 Ω
J31-2 (SPD) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)
U152474E02
2.813,1.333 2.813,2.083 2.813,2.083 2.875,2.083 true 5.49,1.646 5.49,2.125 5.49,2.125 5.604,2.125 true 0.271,0.104 2.552,0.479 2.281,0.375 10 false Front view of wire harness connector: (to Skid Control ECU) 4,0.104 6.281,0.469 2.281,0.365 10 false Front view of wire harness connector: (to Combination Meter) 2.021,0.833 2.292,0.979 0.271,0.146 10 false A17 5.417,0.896 5.708,1.042 0.292,0.146 10 false J28 2.938,2 3.281,2.188 0.344,0.188 10 false SP1 5.656,2.042 5.885,2.229 0.229,0.188 10 false SI

a.

Disconnect the A17 skid control ECU connector.


b.

Disconnect the J28 meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-3 (SP1) - J28-30 (SI) Always Below 1 Ω
A17-3 (SP1) - Body ground Always 10 kΩ or higher




OK

5.CHECK DTC (SFI SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DTC (SFI SYSTEM)
a.

Check for DTCs.

HINT:


Result
Result Proceed to
DTC P0500 is not output A
DTC P0500 is output B



A

6.REPLACE TIRE PRESSURE WARNING ECU

B

6.REPLACE TIRE PRESSURE WARNING ECU
a.

Replace the tire pressure warning ECU (See page Drivetrain>TIRE AND WHEEL>TIRE PRESSURE WARNING ECU>REMOVAL).



NEXT

7.PERFORM REGISTRATION OF TRANSMITTER ID
7.PERFORM REGISTRATION OF TRANSMITTER ID

NEXT

8.PERFORM INITIALIZATION
8.PERFORM INITIALIZATION

NEXT

9.CHECK DTC
9.CHECK DTC
a.

Perform a driving test.


b.

Check for DTCs.

HINT:

The time required for DTC C2174 to be stored is 20 minutes.


Result
Result Proceed to
DTC C2174 is output A
DTC C2174 is not output B



A

REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER

B

END