Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17A8  Transfer Shift Motor Control Circuit Circuit Open  P17A9  Transfer Shift Motor Control Circuit Low  


DESCRIPTION

This DTC is detected when an open circuit or short to ground is detected in the transfer shift motor drive circuit.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17A8
1.

Ignition switch ON (when transfer shift motor is not operating)

2.

Open circuit in the transfer shift motor drive circuit

3.

1 second or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly


P17A9
1.

Ignition switch ON (when transfer shift motor is not operating)

2.

Short to ground in the transfer shift motor drive circuit

3.

1 second or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly



WIRING DIAGRAM

C290925E02
1.021,0.771 1.844,1.208 0.823,0.438 10 false Transfer Shift Motor 2.146,0.635 2.604,0.833 0.458,0.198 10 false TM1 2.135,1.302 2.594,1.5 0.458,0.198 10 false TM2 4.635,1.99 5.094,2.188 0.458,0.198 10 false A26 0.813,2.125 2.927,2.333 2.115,0.208 10 false Transfer Shift Actuator Assembly 0.802,1.969 1.26,2.167 0.458,0.198 10 false D67 4.635,2.188 6.354,2.385 1.719,0.198 10 false 4 Wheel Drive Control ECU 4.979,0.771 5.438,0.969 0.458,0.198 10 false TM1 5,1.469 5.458,1.667 0.458,0.198 10 false TM2 2.583,0.667 2.74,0.865 0.156,0.198 10 false 1 4.729,0.646 4.885,0.844 0.156,0.198 10 false 1 4.729,1.333 4.885,1.531 0.156,0.198 10 false 2 2.563,1.333 2.719,1.531 0.156,0.198 10 false 2

PROCEDURE

1.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)
U152690E02
1.125,1.667 0.573,2.542 false 1.458,1.667 1.906,2.594 false 1.583,0.792 1.917,0.969 0.333,0.177 10 false A26 0.375,2.573 0.719,2.802 0.344,0.229 10 false TM1 1.802,2.615 2.146,2.844 0.344,0.229 10 false TM2 0.167,0.177 0.5,0.406 0.333,0.229 10 false *a

a.

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-1 (TM1) - A26-2 (TM2) Always Below 5 Ω
A26-1 (TM1) or A26-2 (TM2) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the A26 4 wheel drive control ECU connector.


b.

Disconnect the D67 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-1 (TM1) - D67-1 (TM1) Always Below 1 Ω
A26-2 (TM2) - D67-2 (TM2) Always Below 1 Ω
A26-1 (TM1) or D67-1 (TM1) - Body ground Always 10 kΩ or higher
A26-2 (TM2) or D67-2 (TM2) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR