Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17AB  Transfer Shift Motor Position Circuit  


DESCRIPTION

This DTC is detected when a short to ground is detected in the limit switch circuit, which detects the position of the transfer shift motor.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17AB
1.

Immediately after turning the ignition switch to ON and driving mode is being switched

2.

Short to ground in either the TL1, TL2, TL3, TL4 or GTL terminal circuit

3.

0.02 seconds or more

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly



WIRING DIAGRAM

C290928E02
0.813,2.927 1.198,3.104 0.385,0.177 10 false D68 3.125,0.74 3.51,0.938 0.385,0.198 10 false 1 3.125,1.115 3.302,1.271 0.177,0.156 10 false 2 3.125,1.5 3.302,1.656 0.177,0.156 10 false 3 3.125,1.917 3.302,2.073 0.177,0.156 10 false 4 4.771,0.771 5.042,0.938 0.271,0.167 10 false 18 4.792,1.146 5.063,1.313 0.271,0.167 10 false 20 4.792,1.521 5.063,1.688 0.271,0.167 10 false 26 4.792,1.948 5.063,2.115 0.271,0.167 10 false 24 4.802,2.323 5.073,2.49 0.271,0.167 10 false 22 3.125,2.323 3.396,2.49 0.271,0.167 10 false 5 5.135,0.844 5.615,1.042 0.479,0.198 10 false TL1 5.125,1.229 5.604,1.427 0.479,0.198 10 false TL2 5.135,1.625 5.615,1.823 0.479,0.198 10 false TL3 5.146,2.01 5.625,2.208 0.479,0.198 10 false TL4 5.135,2.406 5.615,2.604 0.479,0.198 10 false GTL 2.688,0.74 3,0.906 0.313,0.167 10 false TL1 2.698,1.156 3,1.333 0.302,0.177 10 false TL2 2.698,1.542 2.969,1.698 0.271,0.156 10 false TL3 2.708,1.927 3.01,2.104 0.302,0.177 10 false TL4 2.688,2.344 3,2.521 0.313,0.177 10 false GTL 4.604,2.948 4.99,3.125 0.385,0.177 10 false A26 1.729,2.542 2.542,2.719 0.813,0.177 10 false Limit Switch 0.823,3.115 2.99,3.313 2.167,0.198 10 false Transfer Shift Actuator Assembly 4.615,3.135 6.323,3.344 1.708,0.208 10 false 4 Wheel Drive Control ECU

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the A26 4 wheel drive control ECU connector.


b.

Disconnect the D68 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-18 (TL1) or D68-1 (TL1) - Body ground Always 10 kΩ or higher
A26-20 (TL2) or D68-2 (TL2) - Body ground Always 10 kΩ or higher
A26-26 (TL3) or D68-3 (TL3) - Body ground Always 10 kΩ or higher
A26-24 (TL4) or D68-4 (TL4) - Body ground Always 10 kΩ or higher
A26-22 (GTL) or D68-5 (GTL) - Body ground Always 10 kΩ or higher




OK

2.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (LIMIT SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (LIMIT SWITCH)
C199218E03
1.323,1.969 0.792,1.26 false 1.552,1.948 1.219,1.26 false 1.906,1.969 1.75,1.219 false 2.125,1.969 2.396,1.323 false 2.125,2.229 2.635,2.635 false 0.167,0.125 0.479,0.313 0.313,0.188 10 false *a 1.052,1.042 1.479,1.219 0.427,0.177 10 false TL3 1.625,1.021 1.917,1.198 0.292,0.177 10 false TL2 0.573,1.052 0.865,1.24 0.292,0.188 10 false TL4 2.688,2.594 3,2.781 0.313,0.188 10 false GTL 2.344,1.094 2.635,1.271 0.292,0.177 10 false TL1

a.

Disconnect the D68 transfer shift actuator assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (TL1) - Body ground Always 10 kΩ or higher
2 (TL2) - Body ground Always 10 kΩ or higher
3 (TL3) - Body ground Always 10 kΩ or higher
4 (TL4) - Body ground Always 10 kΩ or higher
5 (GTL) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Transfer Shift Actuator Assembly)



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY