Home › Drivetrain › WF1AM TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM27M0U _52 Drivetrain _049122 WF1AM TRANSFER _0234104 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM J

WF1AM TRANSFER  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  Shift Motor Circuit  


WIRING DIAGRAM

C293134E02
0.896,2.281 3.021,2.5 2.125,0.219 10 false Transfer Shift Actuator Assembly 0.885,2.083 1.219,2.271 0.333,0.188 10 false D67 0.979,0.969 1.802,1.385 0.823,0.417 10 false Transfer Shift Motor 2.135,0.771 2.458,0.99 0.323,0.219 10 false TM1 2.135,1.427 2.458,1.646 0.323,0.219 10 false TM2 4.604,0.885 4.927,1.104 0.323,0.219 10 false A26 4.604,1.552 4.927,1.771 0.323,0.219 10 false A26 4.604,3.656 4.927,3.875 0.323,0.219 10 false A25 4.604,4.323 4.927,4.542 0.323,0.219 10 false A25 4.99,0.885 5.313,1.104 0.323,0.219 10 false TM1 4.969,1.552 5.292,1.771 0.323,0.219 10 false TM2 4.99,4.344 5.313,4.563 0.323,0.219 10 false DM2 2.125,4.208 2.448,4.427 0.323,0.219 10 false DM2 2.146,3.542 2.469,3.76 0.323,0.219 10 false DM1 2.563,0.76 2.719,0.917 0.156,0.156 10 false 1 4.656,0.677 4.979,0.896 0.323,0.219 10 false 1 4.677,3.458 4.854,3.635 0.177,0.177 10 false 1 2.542,3.552 2.708,3.719 0.167,0.167 10 false 1 2.552,4.208 2.74,4.365 0.188,0.156 10 false 2 4.688,4.125 4.844,4.271 0.156,0.146 10 false 2 4.677,1.365 5,1.583 0.323,0.219 10 false 2 2.563,1.427 2.729,1.594 0.167,0.167 10 false 2 1.031,3.813 1.781,4.229 0.75,0.417 10 false A.D.D. Shift Motor 0.792,4.854 1.063,5.042 0.271,0.188 10 false G1 0.792,5.052 2.656,5.417 1.865,0.365 10 false A.D.D. Actuator (Differential Vacuum Actuator Assembly) 4.625,5.031 6.396,5.271 1.771,0.24 10 false 4 Wheel Drive Control ECU 4.99,3.656 5.313,3.875 0.323,0.219 10 false DM1

CAUTION / NOTICE / HINT

NOTICE:

When the vehicle is stopped, mode switching may be unavailable due to the phase of the transfer assembly and A.D.D. actuator powertrain. There is no malfunction if mode switching is available after the vehicle is moved.


PROCEDURE

1.CONFIRM PROBLEM SYMPTOM
a.

Confirm the problem symptoms.

Result
Result Proceed to
The 4HI indicator light is blinking* A
The 4LO indicator light is blinking* B

*: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)




A

2.CHECK A.D.D. POSITION

B

3.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)
2.CHECK A.D.D. POSITION
a.

Move the shift lever to N.


b.

Turn the transfer position switch from 2WD to 4H.

HINT:

The 4HI indicator light continues to blink.



c.

Lift up the vehicle until the 2 front wheels or all four wheels are off the ground.


d.

Release the parking brake.


e.

Rotate the rear propeller shaft and check that the front propeller shaft rotates.

Result
Result Proceed to
The front propeller shaft rotates A
The front propeller shaft does not rotate B



A

B

3.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)
3.CHECK TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)
U152690E02
1.125,1.667 0.573,2.542 false 1.458,1.667 1.906,2.594 false 1.583,0.792 1.917,0.969 0.333,0.177 10 false A26 0.375,2.573 0.719,2.802 0.344,0.229 10 false TM1 1.802,2.615 2.146,2.844 0.344,0.229 10 false TM2 0.167,0.177 0.5,0.406 0.333,0.229 10 false *a

a.

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-1 (TM1) - A26-2 (TM2) Always 1 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)

Result
Result Proceed to
OK A
NG (when 4HI indicator light is blinking*) B
NG (when 4LO indicator light is blinking*) C



A

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)

B

5.CHECK DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY (A.D.D. SHIFT MOTOR)

C

REPLACE 4 WHEEL DRIVE CONTROL ECU

4.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the A26 4 wheel drive control ECU connector.


b.

Disconnect the D67 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A26-1 (TM1) or D67-1 (TM1) - A26-2 (TM2) or D67-2 (TM2) Always 10 kΩ or higher




OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY (A.D.D. SHIFT MOTOR)
U151874E02
1.146,1.542 0.594,2.427 false 1.49,1.552 1.938,2.479 false 1.667,0.563 1.979,0.719 0.313,0.156 10 false A25 0.396,2.448 0.74,2.677 0.344,0.229 10 false DM1 1.844,2.49 2.188,2.719 0.344,0.229 10 false DM2 0.188,0.104 0.521,0.333 0.333,0.229 10 false *a

a.

Disconnect the 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-1 (DM1) - A25-2 (DM2) Always 0.5 Ω or higher


Text in Illustration
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)



OK

6.CHECK HARNESS AND CONNECTOR ( 4 WHEEL DRIVE CONTROL ECU -DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY)

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU

6.CHECK HARNESS AND CONNECTOR ( 4 WHEEL DRIVE CONTROL ECU -DIFFERENTIAL VACUUM ACTUATOR ASSEMBLY)
a.

Disconnect the A25 4 wheel drive control ECU connector.


b.

Disconnect the G1 A.D.D. actuator (differential vacuum actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-1 (DM1) or G1-1 (DM1) - A25-2 (DM2) or G1-2 (DM2) Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR