Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Diagnosis Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the center airbag sensor. When all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C160530E02
1.443,2.558 1.752,2.714 0.309,0.156 10 A24 1.443,2.74 1.773,2.896 0.330,0.156 10 ECM 1.443,4.232 1.745,4.437 0.302,0.205 10 J17 1.443,4.414 1.870,4.577 0.427,0.163 10 DLC3 5.744,4.73 6.073,4.892 0.330,0.163 10 J46 5.744,4.905 7.108,5.081 1.364,0.177 10 Center Airbag Sensor 0.901,5.415 2.899,5.584 1.998,0.170 10 CAN Communication Line 1.125,3.563 1.288,3.740 0.163,0.177 10 4 2.074,3.588 2.278,3.764 0.205,0.177 10 13 1.31,3.686 1.570,3.960 0.260,0.274 10 CG 1.783,3.686 2.154,3.911 0.371,0.225 10 TC 1.584,0.681 1.976,0.864 0.392,0.184 10 CANL 1.57,1.232 1.982,1.381 0.413,0.149 10 CANH 6.017,0.681 6.409,0.864 0.392,0.184 10 CANL 6.017,1.232 6.430,1.381 0.413,0.149 10 CANH 1.78,1.794 2.033,1.957 0.253,0.163 10 TC 2.074,0.554 2.258,0.731 0.184,0.177 10 11 2.067,1.122 2.271,1.299 0.205,0.177 10 10 2.092,1.696 2.303,1.880 0.211,0.184 10 16 3.666,0.921 4.378,1.084 0.711,0.163 10 CAN Line 5.749,0.538 5.997,0.713 0.248,0.174 10 22 5.73,1.099 6.006,1.338 0.276,0.239 10 13

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).

Result
Result Proceed to
DTC is output A
DTC is not output B



B

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

A

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.CHECK HARNESS AND CONNECTOR (DLC3 - ECM)
C353062E01
0.5,1.5 0.896,1.771 0.396,0.271 3.667,1.469 4.063,1.74 0.396,0.271 1.917,1.552 2.229,1.177 true 2.156,2.292 2.052,1.875 true 6.104,0.792 5.958,1.479 true 0.469,0.219 3.375,0.417 2.906,0.198 10 false Front view of DLC3: 4.219,0.208 6.49,0.594 2.271,0.385 10 false Front view of wire harness connector: (to ECM) 0.604,1.552 1.063,1.75 0.458,0.198 10 false J17 3.75,1.51 4.208,1.708 0.458,0.198 10 false A24 6.146,0.625 6.458,0.823 0.313,0.198 10 false TC 2.083,2.323 2.396,2.521 0.313,0.198 10 false TC 2.271,1.073 2.583,1.271 0.313,0.198 10 false CG

a.

Turn the ignition switch off.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J17-13 (TC) - A24-16 (TC) Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
U152947E01
0.035,0.015 1.372,0.206 1.336,0.191 10 Front view of DLC3: 2.039,1.821 2.334,1.977 0.295,0.156 10 CG 1.608,1.048 2.192,1.819 false 0.289,1.092 0.580,1.252 0.290,0.161 10 J17

a.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J17-4 (CG) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
U152344E02
2.344,2.146 0.438,2.896 false 0.073,0.177 2.438,0.531 2.365,0.354 10 false Front view of wire harness connector: (to ECM) 0.323,1.542 0.604,1.708 0.281,0.167 10 false A24 0.188,2.813 0.458,2.99 0.271,0.177 10 false TC

a.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A24-16 (TC) - Body ground Always 1 MΩ or higher


Result
Result Proceed to
NG A
OK (for 1UR-FE) B
OK (for 3UR-FE) C
OK (for 3UR-FBE) D



A

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU

B

C

D