Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1815/54  Short in Front Passenger Side Squib 2nd Step Circuit  B1816/54  Open in Front Passenger Side Squib 2nd Step Circuit  B1817/54  Short to GND in Front Passenger Side Squib 2nd Step Circuit  B1818/54  Short to B+ in Front Passenger Side Squib 2nd Step Circuit  


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor and the front passenger airbag.

The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC Code Detection Condition Trouble Area
B1815/54 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the front passenger side squib 2nd step circuit during primary check.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly


B1816/54 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the front passenger side squib 2nd step circuit for 2 seconds.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly


B1817/54 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the front passenger side squib 2nd step circuit for 0.5 seconds.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly


B1818/54 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the front passenger side squib 2nd step circuit for 0.5 seconds.

·

Front passenger side squib 2nd step malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Instrument panel wire assembly

·

Front passenger airbag assembly (Front passenger side squib 2nd step)

·

Center airbag sensor assembly



WIRING DIAGRAM

C353059E02
3.365,1.208 3.823,1.406 0.458,0.198 10 false JI1 3.365,2.427 3.823,2.625 0.458,0.198 10 false JI1 5.604,1.073 5.76,1.271 0.156,0.198 10 false 1 5.615,2.302 5.771,2.5 0.156,0.198 10 false 2 1.667,1.094 1.823,1.292 0.156,0.198 10 false 1 1.667,2.302 1.823,2.5 0.156,0.198 10 false 2 1.281,1.094 1.594,1.292 0.313,0.198 10 false P2+ 1.281,2.302 1.594,2.5 0.313,0.198 10 false P2- 5.885,1.156 6.198,1.354 0.313,0.198 10 false P2+ 5.906,2.344 6.219,2.542 0.313,0.198 10 false P2- 3.396,2.177 3.552,2.375 0.156,0.198 10 false 4 3.375,0.979 3.531,1.177 0.156,0.198 10 false 3 0.302,3.313 0.615,3.51 0.313,0.198 10 false I1 0.292,3.5 4.271,3.698 3.979,0.198 10 false Front Passenger Side Squib 2nd Step 5.542,3.271 6,3.469 0.458,0.198 10 false J46 5.531,3.448 6.917,3.667 1.385,0.219 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK FRONT PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB 2ND STEP)
U152197E02
0.542,0.813 0.323,1.333 false 1.854,4.167 2.26,4.302 false 2.094,3.708 2.51,3.833 false 0.083,1.365 1.375,1.677 1.292,0.313 10 false Front Passenger Side Squib 2nd Step 1.646,1.604 3.052,1.813 1.406,0.208 10 false Center Airbag Sensor 0.667,0.917 0.813,1.094 0.146,0.177 10 false F 0.865,0.906 1.01,1.083 0.146,0.177 10 false E 1.26,0.885 1.406,1.063 0.146,0.177 10 false D 1.375,0.885 1.521,1.063 0.146,0.177 10 false C 0.375,2.521 2.896,2.927 2.521,0.406 10 false Front view of wire harness connector: (to Front Passenger Side Squib 2nd Step) 0.771,3.656 0.958,3.844 0.188,0.188 10 false I1 2.385,3.302 3.271,3.49 0.885,0.188 10 false Connector E 2.563,3.771 2.875,3.948 0.313,0.177 10 false SST 2.313,4.229 3.115,4.438 0.802,0.208 10 false Color: Black

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front passenger airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the front passenger airbag (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1815, B1816, B1817 or B1818 is not output.


HINT:

Codes other than DTC B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.

Check that the instrument panel wire connectors (on the front passenger airbag side) are not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not damaged or deformed.




OK

3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT
U152201E02
0.635,0.833 0.417,1.354 false 1.531,3.49 1.146,3.76 true 1.615,3.49 2,3.76 true 1.771,4.115 2.188,4.24 false 0.188,1.333 1.49,1.646 1.302,0.313 10 false Front Passenger Side Squib 2nd Step 1.823,1.646 3.229,1.854 1.406,0.208 10 false Center Airbag Sensor 0.75,0.906 0.896,1.083 0.146,0.177 10 false F 0.969,0.906 1.115,1.083 0.146,0.177 10 false E 1.844,0.906 1.99,1.083 0.146,0.177 10 false B 2.208,0.688 2.354,0.865 0.146,0.177 10 false A 1.354,0.896 1.5,1.073 0.146,0.177 10 false D 1.469,0.896 1.615,1.073 0.146,0.177 10 false C 0.281,2.427 2.906,2.781 2.625,0.354 10 false Front view of wire harness connector: (to Front Passenger Side Squib 2nd Step) 0.677,3.396 0.865,3.583 0.188,0.188 10 false I1 2.083,3.302 2.969,3.49 0.885,0.188 10 false Connector E 2.24,4.125 3.156,4.333 0.917,0.208 10 false Color: Black 0.875,3.729 1.167,3.938 0.292,0.208 10 false P2+ 2.021,3.708 2.313,3.917 0.292,0.208 10 false P2-

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
I1-1 (P2+) - Body ground Ignition switch ON Below 1 V
I1-2 (P2-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
I1-1 (P2+) - I1-2 (P2-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
I1-1 (P2+) - I1-2 (P2-) Always 1 MΩ or higher
I1-1 (P2+) - Body ground
I1-2 (P2-) - Body ground




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INSTRUMENT PANEL WIRE ASSEMBLY)
4.CHECK CENTER AIRBAG SENSOR
C162203E02
0.85,0.604 0.577,1.335 false 1.673,1.355 3.077,1.514 1.404,0.158 10 Center Airbag Sensor 1.067,0.708 1.251,0.892 0.184,0.184 10 E 0.94,0.708 1.124,0.892 0.184,0.184 10 F 1.621,0.697 1.804,0.880 0.184,0.184 10 C 1.494,0.697 1.678,0.880 0.184,0.184 10 D 0.024,1.365 1.337,1.693 1.313,0.328 10 Front Passenger Side Squib 2nd Step

a.

Connect the connectors to the front passenger airbag and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1815, B1816, B1817 or B1818 is output (for Column Shift Type) A
DTC B1815, B1816, B1817 or B1818 is output (for Floor Shift Type) B
DTC B1815, B1816, B1817 or B1818 is not output C

HINT:

Codes other than DTC B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.




C

A

B

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - INSTRUMENT PANEL WIRE ASSEMBLY)
U152266E02
1.667,1.01 1.542,1.01 1.542,1.01 1.542,1.438 false 0.521,1.448 0.073,0.292 0.073,0.292 0.198,0.292 false 0.26,0.208 2.813,0.385 2.552,0.177 10 false Front Passenger Side Squib 2nd Step 0.885,0.604 2.958,0.771 2.073,0.167 10 false Instrument Panel Wire Assembly 1.729,0.938 3.135,1.104 1.406,0.167 10 false Instrument Panel Wire 1.979,1.448 2.146,1.615 0.167,0.167 10 false A 1.646,1.646 1.813,1.813 0.167,0.167 10 false B 1.333,1.646 1.5,1.813 0.167,0.167 10 false C 1.146,1.646 1.313,1.813 0.167,0.167 10 false D 0.813,1.646 0.979,1.813 0.167,0.167 10 false E 0.615,1.646 0.781,1.813 0.167,0.167 10 false F 1.5,2.271 2.896,2.458 1.396,0.188 10 false Center Airbag Sensor 0.292,2.76 2.646,3.094 2.354,0.333 10 false Front view of wire harness connector: (to Instrument Panel Wire Assembly) 2.375,3.833 3.208,4.063 0.833,0.229 10 false Connector C 0.323,3.771 0.531,3.948 0.208,0.177 10 false JI1

a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the instrument panel wire connector from the instrument panel wire assembly.


c.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
JI1-3 - Body ground Ignition switch ON Below 1 V
JI1-4 - Body ground



f.

Turn the ignition switch off.


g.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
JI1-3 - JI1-4 Always Below 1 Ω



i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
JI1-3 - JI1-4 Always 1 MΩ or higher
JI1-3 - Body ground
JI1-4 - Body ground




OK

REPLACE INSTRUMENT PANEL WIRE ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE