Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860/64  Short in Driver Side Knee Airbag Squib Circuit  B1861/64  Open in Driver Side Knee Airbag Squib Circuit  B1862/64  Short to GND in Driver Side Knee Airbag Squib Circuit  B1863/64  Short to B+ in Driver Side Knee Airbag Squib Circuit  


DESCRIPTION

The driver side knee airbag squib circuit consists of the center airbag sensor and driver side knee airbag.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.

DTC Code Detection Condition Trouble Area
B1860/64 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the driver side knee airbag squib circuit during the primary check.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly


B1861/64 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the driver side knee airbag squib circuit for 2 seconds.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly


B1862/64 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the driver side knee airbag squib circuit for 0.5 seconds.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly


B1863/64 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the driver side knee airbag squib circuit for 0.5 seconds.

·

A driver side knee airbag squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Driver side knee airbag assembly (Driver side knee squib)

·

Center airbag sensor assembly



WIRING DIAGRAM

C146265E15
0.754,2.937 1.132,3.135 0.378,0.198 10 J110 0.754,3.071 2.762,3.255 2.008,0.184 10 Driver Side Knee Airbag 2.103,1.52 2.397,1.685 0.295,0.165 10 DK+ 2.137,2.52 2.395,2.685 0.258,0.165 10 DK- 2.489,2.313 2.627,2.469 0.137,0.156 10 2 2.492,1.498 2.630,1.691 0.137,0.193 10 1 4.598,1.509 4.727,1.702 0.128,0.193 10 9 4.537,2.314 4.711,2.461 0.174,0.147 10 10 4.817,1.585 5.131,1.759 0.313,0.174 10 DK+ 4.817,2.416 5.131,2.590 0.313,0.174 10 DK- 4.907,4.079 5.202,4.226 0.295,0.147 10 J46 4.908,4.24 6.286,4.433 1.378,0.193 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK DRIVER SIDE KNEE AIRBAG (DRIVER SIDE KNEE SQUIB)
U152366E02
1.979,3.802 2.406,3.948 false 0.917,0.646 0.688,1.115 false 0.156,2.229 2.552,2.583 2.396,0.354 10 false Front view of wire harness connector: (to Driver Side Knee Squib) 1.625,1.135 2.99,1.281 1.365,0.146 10 false Center Airbag Sensor 0.031,1.156 1.198,1.531 1.167,0.375 10 false Driver Side Knee Squib 1.031,0.729 1.167,0.885 0.135,0.156 10 false D 1.24,0.729 1.365,0.885 0.125,0.156 10 false C 2.177,3.146 3.01,3.313 0.833,0.167 10 false Connector C 2.438,3.865 2.771,4.031 0.333,0.167 10 false SST 0.479,3.583 0.844,3.75 0.365,0.167 10 false J110

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the driver side knee airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the driver side knee airbag (driver side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the instrument panel wire connector (on the driver side knee airbag side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG CIRCUIT)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG CIRCUIT)
U152368E01
0.168,2.348 2.542,2.711 2.375,0.363 10 Front view of wire harness connector: (to Driver Side Knee Squib) 1.743,1.078 3.097,1.244 1.354,0.166 10 Center Airbag Sensor 0.688,1.661 2.520,1.862 1.832,0.201 10 Driver Side Knee Squib 1.209,0.709 1.346,0.883 0.137,0.174 10 D 1.395,0.709 1.551,0.855 0.156,0.147 10 C 2.133,0.502 2.270,0.668 0.137,0.165 10 A 1.772,0.714 1.911,0.898 0.139,0.184 10 B 2.138,3.23 3.081,3.386 0.943,0.156 10 Connector C 2.187,3.673 2.497,3.815 0.310,0.142 10 DK- 0.536,3.673 0.852,3.815 0.316,0.142 10 DK+ 0.907,3.707 1.431,3.595 false 1.603,3.595 2.161,3.707 false 0.422,3.221 0.771,3.371 0.350,0.149 10 J110 0.049,0.032 1.445,0.211 1.396,0.179 10 Instrument Panel Wire 1.651,0.504 1.883,0.124 1.883,0.124 1.769,0.124 false

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
J110-1 (DK+) - Body ground Ignition switch ON Below 1 V
J110-2 (DK-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J110-1 (DK+) - J110-2 (DK-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
J110-1 (DK+) - J110-2 (DK-) Always 1 MΩ or higher
J110-1 (DK+) - Body ground Always 1 MΩ or higher
J110-2 (DK-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK CENTER AIRBAG SENSOR
C146268E16
0.854,0.781 0.344,1.771 0.344,1.771 0.427,1.771 false 0.521,1.698 2.104,1.875 1.583,0.177 10 false Driver Side Knee Squib 1.375,1.292 2.76,1.479 1.385,0.188 10 false Center Airbag Sensor 0.969,0.865 1.125,1.031 0.156,0.167 10 false D 1.104,0.865 1.26,1.042 0.156,0.177 10 false C

a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.

Connect the connectors to the driver side knee airbag and center airbag sensor.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.


Result
Result Proceed to
NG (for Column Shift Type) A
NG (for Floor Shift Type) B
OK C



C

A

B