Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Front Driver Side - Side Squib Circuit  B1821/55  Open in Front Driver Side - Side Squib Circuit  B1822/55  Short to GND in Front Driver Side - Side Squib Circuit  B1823/55  Short to B+ in Front Driver Side - Side Squib Circuit  


DESCRIPTION

The side squib LH circuit consists of the center airbag sensor and the front seat side airbag LH.

The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the side squib LH circuit.

DTC Code Detection Condition Trouble Area
B1820/55 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the side squib LH circuit during primary check.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1821/55 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the side squib LH circuit for 2 seconds.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1822/55 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the side squib LH circuit for 0.5 seconds.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly


B1823/55 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the side squib LH circuit for 0.5 seconds.

·

Side squib LH malfunction

·

Center airbag sensor malfunction


·

Floor wire

·

Front seat side airbag assembly LH (Side squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C146254E44
0.738,3.136 2.963,3.306 2.225,0.170 10 Side Squib LH 2.779,1.516 3.189,1.702 0.411,0.186 10 SFL+ 4.773,1.628 5.174,1.814 0.401,0.186 10 SFD+ 2.807,2.342 3.190,2.528 0.383,0.186 10 SFL- 4.78,2.468 5.153,2.655 0.373,0.186 10 SFD- 3.221,1.498 3.363,1.668 0.142,0.170 10 1 3.236,2.348 3.392,2.504 0.156,0.156 10 2 4.584,1.531 4.698,1.694 0.114,0.163 10 9 4.503,2.371 4.709,2.534 0.206,0.163 10 10 4.758,4.118 4.998,4.302 0.239,0.184 10 P1 4.754,4.268 6.197,4.479 1.443,0.211 10 Center Airbag Sensor 0.738,2.965 1.060,3.117 0.323,0.152 10 P12

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK FRONT SEAT SIDE AIRBAG LH (SIDE SQUIB LH)
C353061E01
0.417,3.115 0.833,3.417 0.417,0.302 1.031,1.146 1.031,0.74 false 2.344,4.167 2.188,4.167 2.188,4.167 1.958,3.865 false 2.656,3.688 2.521,3.688 2.521,3.688 2.292,3.531 false 0.427,1.167 1.406,1.427 0.979,0.26 10 false Side Squib LH 1.615,1.25 2.979,1.573 1.365,0.323 10 false Center Airbag Sensor 1.354,0.854 1.51,1.052 0.156,0.198 10 false C 1.146,0.854 1.302,1.052 0.156,0.198 10 false D 0.563,1.917 2.844,2.552 2.281,0.635 10 false Front view of wire harness connector: (to Side Squib LH) 0.229,2.729 1.917,2.927 1.688,0.198 10 false Connector C 0.5,3.188 0.958,3.385 0.458,0.198 10 false P12 2.406,4.104 3.427,4.344 1.021,0.24 10 false Color: Red 2.729,3.604 3.188,3.802 0.458,0.198 10 false SST

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat side airbag LH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat side airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1820, B1821, B1822 or B1823 is not output (for Manual Seat) A
DTC B1820, B1821, B1822 or B1823 is not output (for Power Seat) B
DTC B1820, B1821, B1822 or B1823 is output C

HINT:

Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.




C

2.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)

A

B

2.CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT)
U152934E02
1.5,3.677 0.896,4.198 false 1.792,3.688 2.271,4.229 false 0.781,1.208 1.063,0.729 false 1.49,0.167 1.625,0.167 1.625,0.167 1.625,0.583 false 0.24,1.219 1.229,1.448 0.99,0.229 10 false Side Squib LH 1.688,1.188 3.094,1.417 1.406,0.229 10 false Center Airbag Sensor 0.323,1.781 2.688,2.156 2.365,0.375 10 false Front view of wire harness connector: (to Side Squib LH) 0.219,2.771 1.135,3 0.917,0.229 10 false Connector C 0.438,3.417 0.729,3.583 0.292,0.167 10 false P12 1.375,0.813 1.542,1.01 0.167,0.198 10 false C 1.76,0.813 1.927,1.01 0.167,0.198 10 false B 2.146,0.563 2.313,0.76 0.167,0.198 10 false A 1.156,0.813 1.323,1.01 0.167,0.198 10 false D 0.76,0.083 1.479,0.281 0.719,0.198 10 false Floor Wire 2.083,4.323 2.458,4.49 0.375,0.167 10 false SFL- 0.625,4.271 1,4.438 0.375,0.167 10 false SFL+

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
P12-1 (SFL+) - Body ground Ignition switch ON Below 1 V
P12-2 (SFL-) - Body ground



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P12-1 (SFL+) - P12-2 (SFL-) Always Below 1 Ω



k.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


l.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
P12-1 (SFL+) - P12-2 (SFL-) Always 1 MΩ or higher
P12-1 (SFL+) - Body ground
P12-2 (SFL-) - Body ground




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
C158868E10
0.906,0.802 0.708,1.5 false 1.604,1.25 2.5,1.594 0.896,0.344 10 false Center Airbag Sensor 0.26,1.51 1.208,1.75 0.948,0.24 10 false Side Squib LH 1.021,0.906 1.167,1.094 0.146,0.188 10 false D 1.135,0.906 1.281,1.094 0.146,0.188 10 false C

a.

Connect the connectors to the front seat side airbag LH and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1820, B1821, B1822 or B1823 is output (for Column Shift Type) A
DTC B1820, B1821, B1822 or B1823 is output (for Floor Shift Type) B
DTC B1820, B1821, B1822 or B1823 is not output C

HINT:

Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.




C

A

B