Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM27M0U _58 Vehicle Interior _049131 SUPPLEMENTAL RESTRAINT SYSTEMS _0234204 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1825/56  Short in Front Passenger Side - Side Squib Circuit  B1826/56  Open in Front Passenger Side - Side Squib Circuit  B1827/56  Short to GND in Front Passenger Side - Side Squib Circuit  B1828/56  Short to B+ in Front Passenger Side - Side Squib Circuit  


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and the front seat side airbag RH.

This circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the side squib RH circuit.

DTC Code Detection Condition Trouble Area
B1825/56 When one of the following conditions is met:
·

The center airbag sensor receives a line short circuit signal 5 times in the side squib RH circuit during primary check.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1826/56 When one of the following conditions is met:
·

The center airbag sensor receives an open circuit signal in the side squib RH circuit for 2 seconds.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1827/56 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1828/56 When one of the following conditions is met:
·

The center airbag sensor receives a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.

·

Side squib RH malfunction

·

Center airbag sensor malfunction


·

No. 2 floor wire

·

Front seat side airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C146254E43
0.738,3.12 2.241,3.290 1.503,0.170 10 Side Squib RH 2.802,1.516 3.189,1.702 0.387,0.186 10 SFR+ 4.773,1.628 5.174,1.814 0.401,0.186 10 SFP+ 2.835,2.342 3.190,2.528 0.355,0.186 10 SFR- 4.78,2.468 5.172,2.655 0.392,0.186 10 SFP- 3.221,1.498 3.363,1.668 0.142,0.170 10 1 3.236,2.348 3.392,2.504 0.156,0.156 10 2 4.584,1.531 4.698,1.694 0.114,0.163 10 7 4.584,2.371 4.705,2.534 0.121,0.163 10 6 4.758,4.118 4.998,4.302 0.239,0.184 10 Q1 4.754,4.268 6.197,4.479 1.443,0.211 10 Center Airbag Sensor 0.738,2.955 1.005,3.107 0.267,0.152 10 Q9

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

Perform the simulation method by selecting "check mode" (signal check) with the Techstream (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK FRONT SEAT SIDE AIRBAG RH (SIDE SQUIB RH)
U152935E01
0.068,1.464 1.057,1.694 0.989,0.230 10 Side Squib RH 1.615,1.178 3.021,1.408 1.406,0.230 10 Center Airbag Sensor 0.27,1.921 2.634,2.293 2.364,0.371 10 Front view of wire harness connector: (to Side Squib RH) 0.16,2.644 1.079,2.870 0.920,0.225 10 Connector C 2.752,3.753 3.068,3.923 0.316,0.170 10 SST 2.399,4.302 3.117,4.457 0.718,0.156 10 Color: Red 0.426,3.349 0.672,3.519 0.246,0.170 10 Q9 2.403,3.682 2.695,3.83 false 2.062,4.079 2.406,4.232 false 1.21,1.109 1.375,1.304 0.165,0.195 10 C 0.995,1.109 1.161,1.304 0.165,0.195 10 D 0.859,0.992 0.859,1.431 false

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat side airbag RH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat side airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1825, B1826, B1827 or B1828 is not output (for Manual Seat) A
DTC B1825, B1826, B1827 or B1828 is not output (for Power Seat) B
DTC B1825, B1826, B1827 or B1828 is output C

HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.




C

2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)

A

B

2.CHECK NO. 2 FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
U152936E02
1.552,3.792 1.167,4.292 false 1.833,3.833 2.198,4.292 false 0.573,1.531 0.854,1.052 false 1.417,0.344 1.542,0.344 1.542,0.344 1.375,0.896 false 0.021,1.542 1.01,1.771 0.99,0.229 10 false Side Squib RH 1.719,1.24 2.635,1.604 0.917,0.365 10 false Center Airbag Sensor 0.208,2.073 2.573,2.448 2.365,0.375 10 false Front view of wire harness connector: (to Side Squib RH) 0.146,3.042 1.063,3.271 0.917,0.229 10 false Connector C 0.396,3.573 0.646,3.74 0.25,0.167 10 false Q9 1.125,1.115 1.292,1.313 0.167,0.198 10 false C 1.51,1.125 1.677,1.323 0.167,0.198 10 false B 1.875,0.865 2.042,1.063 0.167,0.198 10 false A 0.917,1.115 1.083,1.313 0.167,0.198 10 false D 2.229,4.229 2.646,4.396 0.417,0.167 10 false SFR- 0.677,4.229 1.094,4.396 0.417,0.167 10 false SFR+ 0.333,0.25 1.385,0.417 1.052,0.167 10 false No. 2 Floor Wire

a.

Turn the ignition switch off.


b.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON.


g.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
Q9-1 (SFR+) - Body ground Ignition switch ON Below 1 V
Q9-2 (SFR-) - Body ground



h.

Turn the ignition switch off.


i.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.


j.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q9-1 (SFR+) - Q9-2 (SFR-) Always Below 1 Ω



k.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


l.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
Q9-1 (SFR+) - Q9-2 (SFR-) Always 1 MΩ or higher
Q9-1 (SFR+) - Body ground
Q9-2 (SFR-) - Body ground




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
C172068E10
1.094,1.146 0.771,1.615 false 0.198,1.677 1.323,1.896 1.125,0.219 10 false Side Squib RH 1.198,1.229 1.323,1.427 0.125,0.198 10 false D 1.344,1.229 1.49,1.417 0.146,0.188 10 false C 1.604,1.302 2.969,1.469 1.365,0.167 10 false Center Airbag Sensor

a.

Connect the connectors to the front seat side airbag RH and the center airbag sensor.


b.

Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1825, B1826, B1827 or B1828 is output (for Column Shift Type) A
DTC B1825, B1826, B1827 or B1828 is output (for Floor Shift Type) B
DTC B1825, B1826, B1827 or B1828 is not output C

HINT:

Codes other than DTC B1825, B1826, B1827 and B1828 may be output at this time, but they are not related to this check.




C

A

B