Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049135 AUDIO / VIDEO _0234292 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Illumination Circuit  


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch assembly illumination when the headlight dimmer switch assembly is in the tail or head position.

WIRING DIAGRAM

E280913E03
6.132,0.468 6.482,0.637 0.350,0.170 10 ILL+ 5.719,0.468 6.083,0.637 0.364,0.170 10 J137 5.778,0.273 6.003,0.443 0.225,0.170 10 10 6.125,3.443 6.475,3.613 0.350,0.170 10 SWG 5.723,3.443 6.074,3.613 0.351,0.170 10 J139 5.792,3.237 6.018,3.407 0.225,0.170 10 23 4.849,3.435 5.246,3.605 0.397,0.170 10 J45 4.925,3.238 5.150,3.408 0.225,0.170 10 3 3.742,3.435 4.036,3.605 0.295,0.170 10 z3 4.236,3.33 4.726,3.499 0.489,0.170 10 EAU 3.966,4.007 4.890,4.353 0.924,0.346 10 Spiral Cable Sub-assembly 3.772,3.238 3.997,3.408 0.225,0.170 10 7 4.848,1.088 5.244,1.258 0.397,0.170 10 J45 4.885,0.871 5.111,1.041 0.225,0.170 10 12 3.716,1.088 4.011,1.258 0.295,0.170 10 z3 4.232,0.99 4.721,1.159 0.489,0.170 10 IL+2 0.263,0.455 1.544,0.624 1.281,0.170 10 from PANEL Fuse 3.746,0.871 3.972,1.041 0.225,0.170 10 5 6.123,5.818 6.473,5.988 0.350,0.170 10 ILL- 3.673,5.722 4.023,5.892 0.350,0.170 10 22 2.253,6.215 2.622,6.385 0.369,0.170 10 J28 2.253,6.34 4.148,6.510 1.894,0.170 10 Combination Meter Assembly 0.738,5.315 2.022,5.662 1.284,0.347 10 Steering Pad Switch Assembly 0.829,4.86 2.828,5.029 1.998,0.170 10 Steering Pad Switch RH Side 0.689,3.66 2.687,3.829 1.998,0.170 10 Steering Pad Switch LH Side 1.061,4.497 1.615,4.667 0.554,0.170 10 Voice 1.412,3.24 2.646,3.409 1.235,0.170 10 MODE 1.185,2.693 2.850,2.862 1.665,0.170 10 On/off hook 1.216,2.252 1.700,2.422 0.485,0.170 10 Seek- 1.725,2.252 2.322,2.422 0.597,0.170 10 Volume- 1.216,1.622 1.700,1.792 0.485,0.170 10 Seek+ 1.725,1.622 2.322,1.792 0.597,0.170 10 Volume+ 3.299,5.815 3.650,5.985 0.350,0.170 10 ILL- 5.719,5.818 6.083,5.988 0.364,0.170 10 J138 5.833,5.608 5.954,5.777 0.121,0.170 10 5 5.829,6.071 7.105,6.444 1.276,0.373 10 Radio and Display Receiver Assembly

CAUTION / NOTICE / HINT

CAUTION:

The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, glove box or other parts (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result
Result Proceed to
Illumination comes on for all components except steering pad switch assembly A
Illumination comes on for all components except radio and display receiver assembly B
No illumination comes on (radio and display receiver assembly, hazard switch, glove box, etc.) C
Illumination comes on for all components except steering pad switch assembly and radio and display receiver assembly D



A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)

B

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)

C

D

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY)
a.
U152693E01
2.504,1.762 2.830,1.908 0.326,0.147 10 IL+2 2.103,1.682 2.305,1.86 2.305,1.86 2.474,1.86 false 0.045,0.038 0.377,0.234 0.332,0.196 10 *a 0.664,1.404 0.962,1.585 0.297,0.181 10 J45

Disconnect the spiral cable sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J45-12 (IL+2) - Body ground Headlight dimmer switch assembly tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEERING PAD SWITCH>REMOVAL).


b.

Inspect the steering pad switch assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEERING PAD SWITCH>INSPECTION).



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly (See pageVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL ).


b.

Inspect the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the J139 radio and display receiver assembly connector.


b.

Disconnect the J45 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J139-23 (SWG) - J45-3 (EAU) Always Below 1 Ω
J139-23 (SWG) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)
a.
U152826E01
1.501,0.274 1.864,0.458 0.363,0.184 10 J137 0.053,0 0.347,0.184 0.293,0.184 10 *a 2.785,1.735 3.150,1.919 0.366,0.184 10 ILL+ 2.321,1.4 2.496,1.818 2.496,1.818 2.762,1.818 false

Disconnect the radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J137-10 (ILL+) - Body ground Headlight dimmer switch assembly tail or head position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the J138 radio and display receiver assembly connector.


b.

Disconnect the J28 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J138-5 (ILL-) - J28-22 (ILL-) Always Below 1 Ω
J138-5 (ILL-) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR