Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

The main body ECU (driver side junction block assembly) receives seat memory switch signals from the outer mirror control ECU assembly via CAN communication. If the seat memory SET switch is being pressed when one of the M1or M2 switches is pressed, or if wither of the M1 or M2 switches is pressed within 3 seconds of pressing the seat memory SET switch, the main body ECU (driver side junction block assembly) sends a memory request signal to the position control ECU and switch assembly. After receiving the request signal, the position control ECU and switch assembly memorizes the location data of each motor.

WIRING DIAGRAM

B352953E05
5.198,1.823 5.479,2 0.281,0.177 10 false N6 5.146,0.198 5.51,0.354 0.365,0.156 10 false MRY 5.75,0.417 6.052,0.594 0.302,0.177 10 false SET 4.958,0.208 5.115,0.385 0.156,0.177 10 false 1 5.156,0.594 5.427,0.771 0.271,0.177 10 false M1 4.958,0.615 5.115,0.792 0.156,0.177 10 false 2 5.146,0.979 5.417,1.156 0.271,0.177 10 false M2 5.854,0.792 6.125,0.969 0.271,0.177 10 false 1 5.854,1.177 6.125,1.354 0.271,0.177 10 false 2 4.958,1.01 5.115,1.188 0.156,0.177 10 false 3 5.146,1.396 5.417,1.573 0.271,0.177 10 false E 3.75,0.24 4.01,0.417 0.26,0.177 10 false MM 3.792,0.635 4.01,0.813 0.219,0.177 10 false M1 3.792,1.031 4,1.208 0.208,0.177 10 false M2 3.552,1.427 4.01,1.604 0.458,0.177 10 false MSWE 4.969,1.406 5.125,1.583 0.156,0.177 10 false 4 4.104,0.198 4.354,0.375 0.25,0.177 10 false 9 4.104,0.594 4.354,0.771 0.25,0.177 10 false 8 4.104,0.99 4.354,1.167 0.25,0.177 10 false 7 4.094,1.375 4.344,1.552 0.25,0.177 10 false 10 5.198,1.979 6.552,2.167 1.354,0.188 10 false Seat Memory Switch 2.979,1.771 3.26,1.948 0.281,0.177 10 false N8 2.979,1.927 4.25,2.406 1.271,0.479 10 false Outer Mirror Control ECU Assembly 0.635,1.333 2.031,1.688 1.396,0.354 10 false Position Control ECU and Switch Assembly 0.479,2.719 2.333,3.073 1.854,0.354 10 false Main Body ECU (Driver Side Junction Bock Assembly) 0.781,3.385 2.635,3.583 1.854,0.198 10 false : CAN Communication Line

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

CAN communication DTC is not output.




OK

2.CHECK FRONT POWER SEAT OPERATION

NG

2.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Each function of the power seat operates normally by using the power seat switches.




OK

3.READ VALUE USING TECHSTREAM (SEAT MEMORY SWITCH)

NG

3.READ VALUE USING TECHSTREAM (SEAT MEMORY SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the Techstream.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
SET Switch Seat memory switch SET signal / ON or OFF ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
M1 Switch Seat memory switch M1 signal / ON or OFF ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
M2 Switch Seat memory switch M2 signal / ON or OFF ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-


OK:

ON or OFF is displayed on the Techstream according to the table above.



OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (BUZZER)

NG

9.INSPECT SEAT MEMORY SWITCH
4.PERFORM ACTIVE TEST USING TECHSTREAM (BUZZER)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the Techstream.

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Buzzer Buzzer operation ON / OFF -


OK:

Buzzer sounds normally.



OK

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
a.

Temporarily replace the outer mirror ECU assembly with a new or normally functioning one (See page Vehicle Interior>ENGINE HOOD / DOOR>FRONT DOOR(for CrewMax)>DISASSEMBLY).



NEXT

6.CHECK SEAT POSITION MEMORY FUNCTION
6.CHECK SEAT POSITION MEMORY FUNCTION
a.

Perform a memory operation and check that the buzzer sounds to indicate the completion of the memory operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.




OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).



NEXT

8.CHECK SEAT POSITION MEMORY FUNCTION
8.CHECK SEAT POSITION MEMORY FUNCTION
a.

Perform a memory operation and check that the buzzer sounds to indicate the completion of the memory operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 seat memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.




OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

9.INSPECT SEAT MEMORY SWITCH

OK

10.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - SEAT MEMORY SWITCH)

NG

10.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY - SEAT MEMORY SWITCH)
a.

Disconnect the N8 outer mirror control ECU assembly connector.


b.

Disconnect the N6 seat memory switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N8-9 (MM) - N6-1 (MRY) Always Below 1 Ω
N8-8 (M1) - N6-2 (M1) Always Below 1 Ω
N8-7 (M2) - N6-3 (M2) Always Below 1 Ω
N8-10 (MSWE) - N6-4 (E) Always Below 1 Ω
N8-9 (MM) or N6-1 (MRY) - Body ground Always 10 kΩ or higher
N8-8 (M1) or N6-2 (M1) - Body ground Always 10 kΩ or higher
N8-7 (M2) or N6-3 (M2) - Body ground Always 10 kΩ or higher
N8-10 (MSWE) or N6-4 (E) - Body ground Always 10 kΩ or higher




OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR