Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM Y

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

IMPORTANT POINT CONCERNING TROUBLESHOOTING


CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

Refer to the troubleshooting procedures of each system if DTCs regarding the CAN communication system are not output.

·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

*: Use the Techstream.



a.

DTCs indicating a CAN communication malfunction are also stored due to internal or power source-related problems in ECUs or sensors of systems using CAN communication. Therefore, check whether codes indicating internal or power source-related problems in those systems are output together with the CAN communication DTCs.


b.

It is possible to inspect the circuit of the DLC3 CAN branch line or V bus main line for malfunctions by inspecting the terminals of the DLC3 using SST.

NOTICE:

It is only possible to inspect CAN branch wires to ECUs (sensors) or the V bus from the DLC3.



c.

It is possible to check which ECUs (sensors) are not able to communicate via CAN communication by checking the "Bus Check" function of the Techstream (when the DLC3 CAN branch wire and V bus CAN main wire are normal).

HINT:
·

When checking "Bus Check", ECUs (sensors) whose CAN branch wire is open or that cannot communicate via CAN communication do not respond to the Techstream (they are not displayed on the screen).

·

When checking "Bus Check", if a DTC indicating a CAN communication malfunction is output even though all ECUs (sensors) respond (they are displayed on the screen), use the DTC combination table to determine the suspected trouble area and perform symptom simulation.




d.

For past malfunctions of the V bus, the ECUs (sensors) which cannot communicate via CAN communication can be determined from the combination of CAN communication DTCs that are output.


e.

The network gateway ECU detects malfunctions in the V2 bus circuit and stores DTCs depending on the malfunctioning areas. The ECUs (sensors) which cannot communicate via CAN communication can be determined from the combination of CAN communication DTCs that are output.


f.

The main body ECU (driver side junction block assembly) detects malfunctions in the MS bus circuit and stores DTCs depending on the malfunctioning areas. The ECUs (sensors) which cannot communicate via CAN communication can be determined from the combination of CAN communication DTCs that are output.


g.

When an open circuit malfunction is confirmed, before disconnecting the connectors for inspection, check whether the connectors are loose by pushing in the connector case.


h.

When a connector is disconnected, check if the connector terminals or case is damaged, deformed, deteriorated, etc.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Result
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding.

Result:
Result
NEXT



NEXT

3.CHECK FOR DTC*
3.CHECK FOR DTC*
a.

Using the Techstream, check for all DTCs.

NOTICE:
·

If codes indicating internal or power source-related malfunctions of ECUs or sensors are output together with codes indicating that those ECUs or sensors cannot communicate via CAN communication, it is likely that the problem is not in the CAN communication line. Therefore, perform troubleshooting for the DTCs related to the malfunctioning parts first.

·

If a connector of a system which includes a CAN communication line is disconnected when the ignition switch is ON or ACC, CAN communication DTCs will be stored by that system and any related systems.




Result:
Result
NEXT



NEXT

4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION
4.CHECK INSTALLED SYSTEMS (ECU AND SENSOR) THAT USE CAN COMMUNICATION
a.

Based on the vehicle equipment and specifications, confirm the systems that use CAN communication.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result
NEXT



NEXT

5.CHECK FOR OPEN CIRCUIT IN DLC3 BRANCH WIRE AND V BUS CIRCUIT CAN MAIN WIRE AND SHORT CIRCUIT (CANH - CANL)
5.CHECK FOR OPEN CIRCUIT IN DLC3 BRANCH WIRE AND V BUS CIRCUIT CAN MAIN WIRE AND SHORT CIRCUIT (CANH - CANL)
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and CAN branch wire.


b.
U152555C01
1.927,0.938 2.115,0.448 2.115,0.448 2.25,0.448 true 1.948,1.479 1.802,1.906 1.802,1.906 1.667,1.906 true 0.094,0.083 0.375,0.302 0.281,0.219 10 false *a 2.302,0.354 2.771,0.542 0.469,0.188 10 false CANH 1.25,1.813 1.719,2 0.469,0.188 10 false CANL 0.26,1.104 0.583,1.323 0.323,0.219 10 false J17
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Proceed to
J17-6 (CANH) - J17-14 (CANL) Ignition switch off OK (54 to 69 Ω) A
J17-6 (CANH) - J17-14 (CANL) Ignition switch off NG (Higher than 70 Ω) B
J17-6 (CANH) - J17-14 (CANL) Ignition switch off NG (Below 53 Ω) C




A

6.CHECK FOR SHORT TO B+ IN CAN V BUS (CANH, CANL - BAT)

B

C

6.CHECK FOR SHORT TO B+ IN CAN V BUS (CANH, CANL - BAT)
a.
U152556C01
1.958,0.917 2.146,0.427 2.146,0.427 2.281,0.427 true 2.313,1.469 2.469,1.896 2.469,1.896 2.594,1.896 true 1.948,1.448 1.802,1.875 1.802,1.875 1.667,1.875 true 0.25,1.104 0.583,1.302 0.333,0.198 10 false J17 0.094,0.094 0.333,0.302 0.24,0.208 10 false *a 2.333,0.313 2.802,0.5 0.469,0.188 10 false CANH 1.198,1.76 1.646,1.969 0.448,0.208 10 false CANL 2.646,1.802 3.052,1.99 0.406,0.188 10 false BAT
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J17-6 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J17-14 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher



Result:
Result
OK
NG



OK

7.CHECK FOR SHORT TO GND IN CAN V BUS (CANH, CANL - CG)

NG

7.CHECK FOR SHORT TO GND IN CAN V BUS (CANH, CANL - CG)
a.
U152557C01
1.583,0.906 1.396,0.417 1.396,0.417 1.26,0.417 true 1.948,0.906 2.135,0.417 2.135,0.417 2.271,0.417 true 1.958,1.458 1.813,1.885 1.813,1.885 1.677,1.885 true 0.25,1.094 0.594,1.281 0.344,0.188 10 false J17 0.135,0.073 0.302,0.26 0.167,0.188 10 false *a 2.333,0.313 2.802,0.5 0.469,0.188 10 false CANH 0.969,0.333 1.438,0.521 0.469,0.188 10 false CG 1.229,1.792 1.677,1.979 0.448,0.188 10 false CANL
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J17-6 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J17-14 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher



Result:
Result
OK
NG



OK

8.CHECK ECUS CONNECTED TO CAN BUS*

NG

8.CHECK ECUS CONNECTED TO CAN BUS*
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

c.

Check the display of the connected ECUs and sensors for a minute.

Result:
Inspection Result Proceed to
All ECUs and sensors connected to CAN communication system are displayed on screen (CAN bus circuit currently normal). A
Except for network gateway ECU, no ECUs connected to V2 bus are displayed (V2 bus CAN main wire open or short malfunction). B
No ECUs connected to V2 bus are displayed (CAN branch wire between network gateway ECU and V bus circuit is open). C
Except for main body ECU (driver side junction block assembly), no ECUs connected to MS bus are displayed (MS bus CAN main wire open or short malfunction). D
No ECUs connected to MS bus are displayed (CAN branch wire between main body ECU [driver side junction block assembly] and V bus circuit is open). E
Single ECU or sensor that should be connected to CAN communication is not displayed (ECU or sensor CAN branch wire open or communication stop). F
ECU or sensor that should be connected to CAN communication is not displayed or display is intermittent during check (ECU or sensor CAN branch wire open on one side). G


NOTICE:

ECUs and sensors that are not present will not be displayed. Be careful not to mistake them for communication stop malfunctions.


HINT:
·

If the display of an ECU is intermittent during the check, one side of an ECU or sensor CAN branch wire is open (the signal of the ECU is treated as noise, which affects the response and display of the Techstream).

·

The network gateway ECU checks for proper ECU communication for ECUs that are connected to the steering bus and the results are displayed on the Techstream. ECUs that stop communicating with the network gateway ECU for 3 seconds or more will stop being displayed on the Techstream.

·

The network gateway ECU may be malfunctioning if both of the following occur: 1) all ECUs connected to the steering bus are not displayed on the Techstream; and 2) DTC U1002 Lost Communication with Gateway Module is not output.

·

The main body ECU (driver side junction block assembly) checks for proper ECU communication for ECUs that are connected to the steering bus and the results are displayed on the Techstream. ECUs that stop communicating with the main body ECU (driver side junction block assembly) for 3 seconds or more will stop being displayed on the Techstream.

·

The main body ECU (driver side junction block assembly) may be malfunctioning if both of the following occur: 1) all ECUs connected to the steering bus are not displayed on the Techstream; and 2) DTC U1002 Lost Communication with Gateway Module is not output.





A

9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*

B

C

D

E

F

G

9.CHECK COMMUNICATION MALFUNCTION DTC (PAST DTC CHECK)*
a.

b.

Write down all of the DTCs output from each ECU.

HINT:
·

If there are communication malfunction DTCs output but the Techstream "Bus Check - Communication Bus Check" screen displays all of the ECUs and sensors connected to the CAN communication system, the communication malfunction DTCs may be past malfunctions that are no longer present.

·

For V bus CAN main wire malfunctions, DTCs for related ECUs are also output. Therefore, determine the malfunctioning area based on all of the DTCs that are output.

·

For V2 bus malfunctions, DTCs are stored based on the detection of communication stop malfunctions and network malfunctions of ECUs that are connected by the network gateway ECU.

·

For MS bus malfunctions, DTCs are stored based on the detection of communication stop malfunctions and network malfunctions of ECUs that are connected by the main body ECU (driver side junction block assembly).




Result:
Inspection Result Proceed to
ECU connected to V bus outputs communication trouble code. A
Network gateway ECU outputs network malfunction trouble code (U1002).
(V2 bus CAN main wire past malfunction)
B
Main body ECU (driver side junction block assembly) outputs network malfunction trouble code (U1002).
(MS bus CAN main wire past malfunction)
C
Network gateway ECU outputs trouble code other than the network malfunction trouble code (U1002).
(past malfunction of ECU or CAN branch wire connected to V2 bus)
D
Main body ECU (driver side junction block assembly) outputs trouble code other than the network malfunction trouble code (U1002).
(past malfunction of ECU or CAN branch wire connected to MS bus)
D



A

10.CHECK DTC COMBINATION TABLE (V BUS BRANCH WIRE OPEN, PAST COMMUNICATION STOP MALFUNCTION)

B

C

D

10.CHECK DTC COMBINATION TABLE (V BUS BRANCH WIRE OPEN, PAST COMMUNICATION STOP MALFUNCTION)
a.

Based on the combination of output CAN communication system DTCs, determine which ECUs and sensors have a communication stop malfunction.

Click herePower Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result
NEXT



NEXT

11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT CAN MAIN WIRE PAST MALFUNCTION)*
11.PERFORM MALFUNCTION SIMULATION TEST (V BUS CIRCUIT CAN MAIN WIRE PAST MALFUNCTION)*
a.

Using the Techstream, clear all DTCs.


b.

Perform a malfunction simulation test on all harnesses and connectors related to the V bus CAN main wire.


c.

Check the DTCs that were output as a result of the malfunction simulation test. Then determine the malfunctioning area.


Result:
Proceed to
NEXT



NEXT

12.ADJUST, REPAIR AND REPLACE
12.ADJUST, REPAIR AND REPLACE
Result:
Proceed to
NEXT



NEXT

13.CLEAR DTC*
13.CLEAR DTC*
a.

Using the Techstream, clear all DTCs.


Result:
Proceed to
NEXT



NEXT

14.CONFIRMATION TEST
14.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END