Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM27M0U _58 Vehicle Interior _049136 SEAT _0234304 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat does not Return to Memorized Position  


DESCRIPTION

When any of the M1or M2 switches is pressed, the front outer mirror control ECU assembly sends a switch signal to the main body ECU (driver side junction block assembly) via CAN communication. Then, the main body ECU (driver side junction block assembly) sends a recall request signal to the position control ECU and switch assembly. The position control ECU and switch assembly operates each motor to achieve each memorized position value.

WIRING DIAGRAM

B352953E05
5.198,1.823 5.479,2 0.281,0.177 10 false N6 5.146,0.198 5.51,0.354 0.365,0.156 10 false MRY 5.75,0.417 6.052,0.594 0.302,0.177 10 false SET 4.958,0.208 5.115,0.385 0.156,0.177 10 false 1 5.156,0.594 5.427,0.771 0.271,0.177 10 false M1 4.958,0.615 5.115,0.792 0.156,0.177 10 false 2 5.146,0.979 5.417,1.156 0.271,0.177 10 false M2 5.854,0.792 6.125,0.969 0.271,0.177 10 false 1 5.854,1.177 6.125,1.354 0.271,0.177 10 false 2 4.958,1.01 5.115,1.188 0.156,0.177 10 false 3 5.146,1.396 5.417,1.573 0.271,0.177 10 false E 3.75,0.24 4.01,0.417 0.26,0.177 10 false MM 3.792,0.635 4.01,0.813 0.219,0.177 10 false M1 3.792,1.031 4,1.208 0.208,0.177 10 false M2 3.552,1.427 4.01,1.604 0.458,0.177 10 false MSWE 4.969,1.406 5.125,1.583 0.156,0.177 10 false 4 4.104,0.198 4.354,0.375 0.25,0.177 10 false 9 4.104,0.594 4.354,0.771 0.25,0.177 10 false 8 4.104,0.99 4.354,1.167 0.25,0.177 10 false 7 4.094,1.375 4.344,1.552 0.25,0.177 10 false 10 5.198,1.979 6.552,2.167 1.354,0.188 10 false Seat Memory Switch 2.979,1.771 3.26,1.948 0.281,0.177 10 false N8 2.979,1.927 4.25,2.406 1.271,0.479 10 false Outer Mirror Control ECU Assembly 0.635,1.333 2.031,1.688 1.396,0.354 10 false Position Control ECU and Switch Assembly 0.479,2.719 2.333,3.073 1.854,0.354 10 false Main Body ECU (Driver Side Junction Bock Assembly) 0.781,3.385 2.635,3.583 1.854,0.198 10 false : CAN Communication Line

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the Techstream to check if the CAN communication system is functioning normally (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


OK:

CAN communication DTC is not output.



OK

2.CHECK FRONT POWER SEAT OPERATION

NG

2.CHECK FRONT POWER SEAT OPERATION
a.

Check that each function of the power seat operates normally by using the power seat switches (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

OK:

Each function of the power seat operates normally by using the power seat switches.




OK

3.CHECK SEAT POSITION MEMORY FUNCTION

NG

3.CHECK SEAT POSITION MEMORY FUNCTION
a.

Perform a memory operation and check that the buzzer sounds to indicate the completion of the memory operation (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function operates normally.




OK

4.CHECK SEAT POSITION RESTORING FUNCTION

NG

Go to OTHER FLOW CHART (Power Seat Position is not Memorized)

4.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat restoring function operates by pressing the M1 switch or M2 switch (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).

·

Turn the ignition switch is off.

·

Turn the ignition switch to ON, and shift lever in P.*1

·

Turn the ignition switch is off within 180 seconds after the driver door is closed and opened.*2

·

Turn the ignition switch is off within 60 seconds after the driver door is opened and closed.*3


Result
Result Proceed to
Seat restoring function does not operate at all. A
Seat restoring function does not operate when the condition is [*1]. B
·

Seat restoring function does not operate when the condition is [*2].

·

Seat restoring function does not operate when the condition is [*3].


C



A

5.READ VALUE USING TECHSTREAM (SEAT MEMORY)

B

10.READ VALUE USING TECHSTREAM (P SWITCH)

C

11.READ VALUE USING TECHSTREAM (D DOOR COURTESY)
5.READ VALUE USING TECHSTREAM (SEAT MEMORY)
a.

Perform the seat position memorized function for the M1 switch and M2 switch (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).


b.

Connect the Techstream to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the Techstream on.


e.

Enter the following menus: Body Electrical / Driver Seat / Data List.


f.

Read the Data List according to the display on the Techstream.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-

OK:

Mem appears on the Techstream screen.




OK

6.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

Go to OTHER FLOW CHART (Power Seat Position is not Memorized)

6.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY
a.

Temporarily replace the outer mirror control ECU assembly with a new or normally functioning one (See page Vehicle Interior>ENGINE HOOD / DOOR>FRONT DOOR(for CrewMax)>DISASSEMBLY).



NEXT

7.CHECK SEAT POSITION RESTORING FUNCTION
7.CHECK SEAT POSITION RESTORING FUNCTION
a.

Perform a seat position restoring function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).


b.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat position will not return to the memorized position if 2 seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.



OK:

Seat position restoring function operates normally.




OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

8.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
8.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Temporarily replace the position control ECU and switch assembly with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>DISASSEMBLY).



NEXT

9.CHECK SEAT POSITION RESTORING FUNCTION
9.CHECK SEAT POSITION RESTORING FUNCTION
a.

Perform a seat position memory function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK).


b.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat position will not return to the memorized position if 2 seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.



OK:

Seat position restoring function operates normally.




OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

10.READ VALUE USING TECHSTREAM (P SWITCH)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Driver Seat / Data List.


e.

Read the Data List according to the display on the Techstream.

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Switch Park state signal / ON or OFF ON: Shift lever in P
OFF: Shift lever in a position other than P
-

OK:

On the Techstream screen, the item changes between ON and OFF according to the above.


Result
Result Proceed to
OK A
NG (for AB60E) B
NG (for AB60F) C



A

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

B

C

11.READ VALUE USING TECHSTREAM (D DOOR COURTESY)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the Techstream.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door Courtesy Front door courtesy light switch assembly signal / ON or OFF ON: Driver door open
OFF: Driver door closed
-

OK:

On the Techstream screen, the item changes between ON and OFF according to the above.




OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG