Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM
RM27M0U _51 Engine / Hybrid System _049139 CRUISE CONTROL _0234343 CRUISE CONTROL SYSTEM C

CRUISE CONTROL  CRUISE CONTROL SYSTEM  P0571  Brake Switch "A" Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.

DTC Code DTC Detection Condition Trouble Area
P0571 When voltage of STP terminal and ST1- terminal of ECM are less than 1 V for 0.5 seconds. or more
·

Stop light switch

·

Stop light switch circuit

·

ECM



WIRING DIAGRAM

E146082E04
5.271,2.458 5.667,2.656 0.396,0.198 10 false ECM 5.271,2.302 5.594,2.479 0.323,0.177 10 false A24 4.729,1.281 4.948,1.458 0.219,0.177 10 false 36 4.74,1.885 4.958,2.063 0.219,0.177 10 false 35 2.646,2.271 3.792,2.479 1.146,0.208 10 false Stop Light Switch 2.646,2.115 2.885,2.302 0.24,0.188 10 false A4 3.583,1.281 3.771,1.458 0.188,0.177 10 false 1 3.583,1.865 3.771,2.042 0.188,0.177 10 false 3 2.729,1.281 2.917,1.458 0.188,0.177 10 false 2 2.729,1.865 2.917,2.042 0.188,0.177 10 false 4 1.896,1.333 2.323,1.5 0.427,0.167 10 false STOP 1.948,1.927 2.271,2.094 0.323,0.167 10 false IGN 0.677,1.156 1.542,1.344 0.865,0.188 10 false from Battery 0.5,1.76 1.49,1.948 0.99,0.188 10 false from IG2 Relay 5.052,1.188 5.417,1.375 0.365,0.188 10 false STP 5.052,1.76 5.417,1.948 0.365,0.188 10 false ST1-

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
a.

Using the Techstream, read the Data List (see page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stp Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-

OK:

Normal conditions listed above are displayed.


Result
Result Proceed to
NG A
OK (for 1UR-FE) B
OK (for 3UR-FE) C
OK (for 3UR-FBE) D



A

2.INSPECT STOP LIGHT SWITCH

B

C

D

2.INSPECT STOP LIGHT SWITCH
E146086E04
2.604,1.74 3.021,2.344 false 3,1.073 2.583,1.448 false 2.427,1.729 2.01,2.333 false 1.99,1.073 2.406,1.448 false 0.458,1.542 0.583,1.063 0.583,1.063 0.74,1.063 false 0.115,2.052 0.635,2.396 0.521,0.344 10 false Not Pushed 0.76,2.063 1.281,2.24 0.521,0.177 10 false Pushed 3,2.354 3.156,2.531 0.156,0.177 10 false 1 3.052,0.958 3.208,1.135 0.156,0.177 10 false 2 1.938,2.354 2.094,2.531 0.156,0.177 10 false 3 1.875,0.927 2.031,1.104 0.156,0.177 10 false 4 0.125,0.073 2.656,0.448 2.531,0.375 10 false Component without harness connected: (Stop Light Switch) 0.771,0.979 1.031,1.146 0.26,0.167 10 false Pin

a.

Remove the stop light switch (see page Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin pushed 10 kΩ or higher
Pin not pushed Below 1 Ω
3 - 4 Pin pushed Below 1 Ω
Pin not pushed 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)

NG

REPLACE STOP LIGHT SWITCH

3.CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
U152716E02
0.188,0.083 2.563,0.448 2.375,0.365 10 false Front view of wire harness connector: (to Stop Light Switch) 0.667,1.24 0.906,1.406 0.24,0.167 10 false A4

a.

Disconnect the A4 stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A4-2 - Body ground Always 11 to 14 V
A4-4 - Body ground Ignition switch ON




OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
E337692E02
0.823,1.438 1.219,1.667 0.396,0.229 3.313,1.427 3.708,1.656 0.396,0.229 5.25,1.729 5.073,2.406 5.073,2.406 4.875,2.406 false 5.365,1.729 5.448,2.406 5.448,2.406 5.646,2.406 false 0.156,0.083 2.438,0.469 2.281,0.385 10 false Front view of wire harness connector: (to Stop Light Switch) 0.927,1.469 1.271,1.646 0.344,0.177 10 false A4 3.677,0.083 6,0.469 2.323,0.385 10 false Front view of wire harness connector: (to ECM) 3.396,1.458 3.74,1.635 0.344,0.177 10 false A24 4.49,2.313 4.875,2.49 0.385,0.177 10 false ST1- 5.708,2.323 6.094,2.5 0.385,0.177 10 false STP

a.

Disconnect the A4 stop light switch connector.


b.

Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
A4-1 - A24-36 (STP) Always Below 1 Ω
A4-1 - Body ground Always 10 kΩ or higher
A4-3 - A24-35 (ST1-) Always Below 1 Ω
A4-4 - Body ground Always 10 kΩ or higher


Result
Result Proceed to
NG A
OK (for 1UR-FE) B
OK (for 3UR-FE) C
OK (for 3UR-FBE) D



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

D