Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

If any of the following conditions are detected, the ABS warning light remains on:

1.

The ECU connector is disconnected from the skid control ECU.

2.

There is a malfunction in the skid control ECU internal circuit.

3.

There is an open or short in the CAN communication line between the combination meter and the skid control ECU.


HINT:

The Techstream cannot be used when there is a malfunction in the skid control ECU.


WIRING DIAGRAM

C292872E01
1.16,0.734 1.650,0.927 0.489,0.193 10 CANH 1.16,1.29 1.615,1.466 0.455,0.177 10 CANL 1.707,0.575 1.953,0.745 0.246,0.170 10 39 1.707,1.129 1.974,1.326 0.267,0.198 10 40 1.315,1.913 1.630,2.083 0.316,0.170 10 IG+ 1.735,1.808 1.981,2.013 0.246,0.205 10 2 2.106,3.384 2.956,3.582 0.850,0.198 10 from Battery 1.378,4.897 1.631,5.081 0.253,0.184 10 ES 1.7,4.764 1.939,4.948 0.239,0.184 10 24 2.106,4.085 2.908,4.435 0.802,0.350 10 from Ignition Switch 0.39,5.619 0.719,5.796 0.330,0.177 10 J28 0.39,5.808 1.657,5.978 1.267,0.170 10 Combination Meter 3.668,4.484 4.338,4.654 0.670,0.170 10 IG No. 1 4.684,3.587 5.708,3.764 1.024,0.177 10 ECU-IG No. 1 2.891,2.074 3.283,2.265 0.392,0.191 10 MET 3.92,1.892 4.937,2.090 1.017,0.198 10 from IG2 Relay 3.003,1.024 4.686,1.207 1.684,0.184 10 CAN Communication Line 6.092,0.736 6.595,0.927 0.503,0.191 10 CANH 5.805,0.575 6.079,0.759 0.274,0.184 10 12 5.798,1.129 6.051,1.342 0.253,0.213 10 13 6.092,1.269 6.567,1.487 0.475,0.218 10 CANL 6.099,3.4 6.401,3.584 0.302,0.184 10 IG1 5.882,3.3 6.059,3.498 0.177,0.198 10 8 6.085,4.306 6.630,4.482 0.545,0.177 10 GND1 5.812,4.211 6.091,4.396 0.279,0.185 10 16 5.861,5.626 6.197,5.803 0.336,0.177 10 A17 5.861,5.801 7.121,6.006 1.260,0.205 10 Skid Control ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Make sure the skid control ECU is not in test mode before proceeding.

·

Before using these procedures, first check other DTCs which may cause the ABS warning light to remain on.



PROCEDURE

1.INSPECT CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.INSPECT CONNECTOR CONNECTION CONDITION

B

2.INSPECT CONNECTOR CONNECTION CONDITION
a.

Check the skid control ECU connector connection condition.

OK:

The connector is securely connected.




OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTOR CORRECTLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U152479E01
0.097,0.133 2.454,0.447 2.357,0.313 10 Front view of wire harness connector: (to Skid Control ECU) 0.145,1.501 0.568,1.657 0.423,0.156 10 GND1 0.191,1.159 0.514,1.333 0.323,0.174 10 A17 0.385,1.709 0.385,1.954 false 1.675,1.501 1.922,1.657 0.247,0.156 10 IG1 1.794,1.709 1.794,1.946 false

Disconnect the A17 ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A17-8 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-16 (GND1) - Body ground Always Below 1 Ω




OK

4.PERFORM ACTIVE TEST USING TECHSTREAM (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING TECHSTREAM (ABS WARNING LIGHT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Select the Active Test mode and operate the ABS warning light using the Techstream.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light ON / OFF Observe combination meter


e.

Check that the ABS warning light turns on and off in the combination meter when using the Techstream.

OK:

The ABS warning light turns on and off in accordance with the Techstream operation.


HINT:

When the ABS warning light remains illuminated, there may be an open in the wire harness of the combination meter or abnormalities in the meter circuit.




OK

NG