Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1231/31  Steering Angle Sensor Circuit Malfunction  


DESCRIPTION

The steering angle sensor signal is sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1231/31 When any of following conditions detected:
1.

The ECU-B1 fuse blows or the ignition switch is turned to ON with the ECU-B1 fuse removed.

2.

Skid control ECU receives abnormal signals from steering angle sensor.

3.

Skid control ECU receives abnormal voltage signals from steering angle sensor.

4.

Despite calibration being conducted by skid control ECU, it does not finish within 15 seconds.

5.

Abnormal difference between yaw rate and deceleration sensor and steering angle sensor signals continues for approximately 2 seconds or more during driving.


·

ECU-B1 fuse

·

Steering angle sensor

·

Steering angle sensor circuit

·

Steering angle sensor power supply

·

CAN communication system

·

VSC actuator (skid control ECU)



HINT:

DTC C1231/31 is cleared automatically when the ignition switch is turned from off to ON after the voltage supply to the steering angle sensor returns to normal.


WIRING DIAGRAM

C312611E02
2.948,0.979 4.635,1.146 1.688,0.167 10 false CAN Communication Line 1.927,0.729 2.385,0.896 0.458,0.167 10 false CANL 1.917,1.24 2.375,1.406 0.458,0.167 10 false CANH 5.135,0.75 5.594,0.917 0.458,0.167 10 false CANL 5.156,1.26 5.615,1.427 0.458,0.167 10 false CANH 2.375,0.875 2.667,1.146 0.292,0.271 10 false 13 2.406,1.406 2.635,1.583 0.229,0.177 10 false 12 1.229,1.615 1.583,1.802 0.354,0.188 10 false A17 1.229,1.771 2.458,2 1.229,0.229 10 false Skid Control ECU 3.927,2.875 4.906,3.042 0.979,0.167 10 false ECU-IG No. 1 4.896,1.417 5.125,1.604 0.229,0.188 10 false 10 4.948,0.917 5.135,1.104 0.188,0.188 10 false 9 1.677,3.906 1.927,4.094 0.25,0.188 10 false J9 1.677,4.042 2.688,4.229 1.01,0.188 10 false Ignition Switch 1.698,3.458 2.073,3.646 0.375,0.188 10 false AM1 2.438,3.49 2.813,3.677 0.375,0.188 10 false IG1 1.052,3.469 1.427,3.656 0.375,0.188 10 false AM1 3.083,3.688 3.667,3.885 0.583,0.198 10 false IG No. 1 2.792,3.458 2.969,3.646 0.177,0.188 10 false 1 4.979,2.823 5.156,3.01 0.177,0.188 10 false 1 4.958,4.865 5.135,5.052 0.177,0.188 10 false 3 1.5,3.458 1.677,3.646 0.177,0.188 10 false 4 0.688,3.729 1.271,3.896 0.583,0.167 10 false LH-J/B 0.688,4.281 1.271,4.448 0.583,0.167 10 false ALT 3.229,4.906 3.854,5.125 0.625,0.219 10 false ECU-B1 5.156,2.74 5.833,2.948 0.677,0.208 10 false IG 5.156,4.76 5.75,4.969 0.594,0.208 10 false BAT 5.146,5.604 5.74,5.813 0.594,0.208 10 false ESS 4.948,5.667 5.094,5.854 0.146,0.188 10 false 2 5.198,6.281 5.438,6.458 0.24,0.177 10 false J6 5.188,6.448 6.688,6.635 1.5,0.188 10 false Steering Angle Sensor 0.833,5.5 1.396,5.698 0.563,0.198 10 false Battery

CAUTION / NOTICE / HINT

HINT:

When U0073/94, U0123/62, U0124/69 or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/69 or U0126/63 first.


NOTICE:
·

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM INITIALIZATION OF STEERING ANGLE SENSOR
a.

Check that the steering wheel is in the centered position.


b.

Disconnect the negative battery terminal for more than 2 seconds.

NOTICE:

After the ignition switch is turned off, the navigation system requires approximately 90 seconds to record various types of memory and settings. As a result, after turning the ignition switch off, wait 90 seconds or more before disconnecting the cable from the negative (-) battery terminal.



c.

Reconnect the negative battery terminal.


d.

After driving the vehicle straight ahead at 15 km/h (9.3 mph) or more for a few seconds, drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the steering wheel to the right and left for several seconds.



NEXT

2.READ VALUE USING TECHSTREAM (STEERING ANGLE SENSOR)
2.READ VALUE USING TECHSTREAM (STEERING ANGLE SENSOR)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream ON.


d.

Check that the steering wheel is centered.


e.

Select the Data List mode on the Techstream.

i.

Techstream

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Steering Angle Sensor Steering angle sensor /
min.: -3276.8°, max.: 3276.7°
Left turn: Increase
Right turn: Decrease
-
Steering Angle Value Steering angle value /
min.: -3276.8°, max.: 3276.7°
- -



f.

Check that the steering wheel turning angle of the steering angle sensor changes when turning the steering wheel.

OK:

Turning the steering wheel to the left: Value increases

Turning the steering wheel to the right: Value decreases




OK

3.RECONFIRM DTC

NG

4.CHECK CAN COMMUNICATION SYSTEM
3.RECONFIRM DTC

b.

Start the engine.


c.

After driving the vehicle straight ahead at 15 km/h (9.3 mph) or more for a few seconds, drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the steering wheel to the right and left for several seconds.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B

4.CHECK CAN COMMUNICATION SYSTEM
a.

Check if the CAN communication system DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

5.CHECK STEERING ANGLE SENSOR

B

5.CHECK STEERING ANGLE SENSOR
a.

Check that the steering angle sensor has been installed correctly (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION).

OK:

The sensor is installed correctly.




OK

6.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

INSTALL STEERING ANGLE SENSOR CORRECTLY

6.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
U152119E01
0.279,0.971 0.477,1.117 0.198,0.145 10 J6 0.555,1.427 0.766,1.618 0.211,0.191 10 IG 0.812,1.765 1.166,1.937 0.354,0.172 10 ESS 1.385,1.77 1.715,1.930 0.330,0.161 10 BAT 0.049,0.008 2.465,0.450 2.416,0.443 10 Front view of wire harness connector: (to Steering Angle Sensor) 1.028,1.4 0.758,1.508 false 1.182,1.434 1.064,1.762 false 1.389,1.44 1.488,1.752 false

Remove the steering wheel and the column cover lower.


b.

Disconnect the steering angle sensor connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J6-1(IG) - Body ground Ignition switch ON 11 to 14 V
J6-3 (BAT) - Body ground Always



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J6-2 (ESS) - Body ground Always Below 1 Ω




OK

7.REPLACE STEERING ANGLE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE STEERING ANGLE SENSOR
a.


NEXT

8.RECONFIRM DTC
8.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 45 km/h (28 mph) or more and turn the steering wheel to the right and left for several seconds.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

B

END