Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1340/47  Center Differential Lock Circuit  


DESCRIPTION

The skid control ECU monitors the 2WD/4WD state from both the 4 wheel drive control ECU and the A.D.D. detection switch.

DTC Code DTC Detection Condition Trouble Area
C1340/47 When the terminal IG1 voltage is between 10 and 14 V, there is an open in the A.D.D. detection switch circuit or there is a transfer mechanical malfunction for 2 seconds or more.
·

A.D.D. detection switch

·

A.D.D. detection switch circuit

·

4 wheel drive control ECU

·

Transfer

·

Skid control ECU



WIRING DIAGRAM

C245311E02
0.552,4.032 0.865,4.216 0.313,0.184 10 A25 0.552,4.182 2.008,4.498 1.455,0.316 10 4 Wheel Drive Control ECU 2.831,3.593 4.672,4.110 1.841,0.517 10 G1 A.D.D. Actuator (A.D.D. Detection Switch) 5.708,4.06 6.021,4.244 0.313,0.184 10 A17 5.834,1.968 6.175,2.152 0.341,0.184 10 EXI2 1.145,3.126 1.486,3.310 0.341,0.184 10 ADD 2.831,3.017 2.932,3.201 0.100,0.184 10 3 1.579,0.759 1.773,0.943 0.194,0.184 10 23 1.579,1.273 1.773,1.456 0.194,0.184 10 22 1.571,3.216 1.765,3.400 0.194,0.184 10 18 4.085,3.017 4.186,3.201 0.100,0.184 10 4 5.554,2.09 5.779,2.273 0.225,0.184 10 11 5.554,1.273 5.779,1.456 0.225,0.184 10 13 5.554,0.759 5.779,0.943 0.225,0.184 10 12 5.708,4.247 6.947,4.431 1.239,0.184 10 Skid Control ECU 2.813,1.129 4.441,1.310 1.628,0.181 10 CAN Communication Line 1.085,0.886 1.551,1.069 0.466,0.184 10 CANH 1.085,1.414 1.551,1.598 0.466,0.184 10 CANL 5.849,0.886 6.315,1.069 0.466,0.184 10 CANH 5.849,1.414 6.315,1.598 0.466,0.184 10 CANL 3.016,3.231 3.357,3.415 0.341,0.184 10 ADD 3.681,3.231 4.022,3.415 0.341,0.184 10 GND

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

If the transfer shift actuator cannot change from 2WD to 4WD or 4WD to 2WD, inspect and repair the touch select 2-4 and high-low system first.


PROCEDURE

1.INSPECT SKID CONTROL ECU (EXI2 TERMINAL)
a.

Set the vehicle in 4WD state using the A.D.D. detection switch.


b.
U152478E01
0.097,0.09 2.454,0.418 2.357,0.327 10 Front view of wire harness connector: (to Skid Control ECU) 1.161,1.394 1.486,1.550 0.325,0.156 10 EXI2 0.191,1.356 0.514,1.531 0.323,0.174 10 A17 1.343,1.576 1.343,1.949 false

Disconnect the A17 ECU connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A17-11 (EXI2) - Body ground
·

Ignition switch ON

·

4WD (A.D.D. detection switch ON)


Below 1.5 V



e.

Connect the A17 ECU connector.


f.

Set the vehicle in 2WD state using the A.D.D. detection switch.


g.

Disconnect the A17 ECU connector.


h.

Turn the ignition switch to ON.


i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A17-11 (EXI2) - Body ground
·

Ignition switch ON

·

2WD (A.D.D. detection switch OFF)


10 to 14 V




OK

NG

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU)
a.
U152647E02
1.354,1.25 1.448,1.01 true 1.219,4.052 1.333,4.396 true 0.177,0.031 2.51,0.385 2.333,0.354 10 false Front view of wire harness connector: (to Skid Control ECU) 0.167,0.865 0.49,1.031 0.323,0.167 10 false A17 0.156,3.563 0.479,3.729 0.323,0.167 10 false A25 0.094,2.073 2.448,2.427 2.354,0.354 10 false Front view of wire harness connector: (to 4 Wheel Drive Control ECU) 1.479,0.844 1.823,1 0.344,0.156 10 false EXI2 1.281,4.396 1.656,4.563 0.375,0.167 10 false ADD

Confirm that the skid control ECU connector and 4 wheel drive control ECU connector are properly connected.


b.

Disconnect the A17 and A25 ECU connectors.


c.

Disconnect the G1 A.D.D. actuator connector.


d.

Inspect both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-11 (EXI2) - A25-18 (ADD) Always Below 1 Ω
A17-11 (EXI2) - Body ground Always 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.

Confirm that the 4 wheel drive control ECU connector and A.D.D. actuator connectors are properly connected.

U152648E01
0.158,0.06 2.432,0.390 2.274,0.330 10 Component with harness connected: (4 Wheel Drive Control ECU) 2.83,0.911 3.140,1.049 0.310,0.139 10 A25 3.248,2.16 2.582,3.171 2.582,3.171 2.47,3.171 false 2.12,3.108 2.498,3.278 0.378,0.170 10 ADD


b.

Disconnect the A25 ECU connector.


c.

Inspect the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Connect the A25 ECU connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A25-18 (ADD) - Body ground 4WD
(A.D.D. detection switch ON)
Below 1 Ω
2WD
(A.D.D. detection switch OFF)
10 kΩ or higher




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Start the engine.


c.

Check if the same DTC(s) is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B