Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM27M0U _54 Brake _049153 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0234401 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  AUTO LSD Indicator Light Remains ON  


DESCRIPTION

For 2WD vehicles and 4WD vehicles in H2 mode, if the VSC OFF switch is pressed for a short amount of time (approximately 1 second), or if the vehicle is stopped and the VSC OFF switch is pressed for 3 seconds or more, the AUTO LSD function is activated and the AUTO LSD indicator light illuminates.

WIRING DIAGRAM

C292928E02
1.031,0.792 1.563,0.969 0.531,0.177 10 false CANH 1.042,1.323 1.49,1.542 0.448,0.219 10 false CANL 1.563,0.646 1.844,0.885 0.281,0.24 10 false 39 1.563,1.167 1.865,1.365 0.302,0.198 10 false 40 1.156,1.948 1.469,2.146 0.313,0.198 10 false IG+ 1.594,1.844 1.823,2.063 0.229,0.219 10 false 2 1.229,4.917 1.542,5.115 0.313,0.198 10 false ES 1.552,4.823 1.865,5.042 0.313,0.219 10 false 24 3.698,4.573 4.333,4.771 0.635,0.198 10 false IG No. 1 1.677,4.188 3.063,4.406 1.385,0.219 10 false from Ignition Switch 2.104,3.615 3,3.823 0.896,0.208 10 false from Battery 4.708,3.802 5.688,4.01 0.979,0.208 10 false ECU-IG No. 1 5.75,5.594 6.198,5.792 0.448,0.198 10 false A17 5.75,5.74 6.99,5.938 1.24,0.198 10 false Skid Control ECU 0.313,5.646 0.698,5.844 0.385,0.198 10 false J28 0.292,5.792 1.646,6.021 1.354,0.229 10 false Combination Meter 6.104,4.354 6.625,4.604 0.521,0.25 10 false GND1 5.792,4.25 6.083,4.458 0.292,0.208 10 false 16 6.104,3.646 6.448,3.854 0.344,0.208 10 false IG1 5.865,3.521 6.135,3.76 0.271,0.24 10 false 8 4.365,3.01 5.615,3.208 1.25,0.198 10 false VSC OFF Switch 4.365,2.844 4.729,3.052 0.365,0.208 10 false J22 4.281,2.427 4.531,2.635 0.25,0.208 10 false 6 5.188,2.448 5.427,2.635 0.24,0.188 10 false 9 2.74,2.104 3.167,2.313 0.427,0.208 10 false MET 2.833,1.031 4.552,1.26 1.719,0.229 10 false CAN Communication Line 3.792,1.948 4.906,2.156 1.115,0.208 10 false from IG2 Relay 6.125,1.313 6.667,1.51 0.542,0.198 10 false CANL 5.781,1.177 6.094,1.396 0.313,0.219 10 false 13 6.094,0.75 6.635,0.958 0.542,0.208 10 false CANH 5.781,0.625 6.167,0.844 0.385,0.219 10 false 12 6.115,2.542 6.594,2.74 0.479,0.198 10 false CSW 5.885,2.458 6.146,2.667 0.26,0.208 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

When replacing the VSC actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.INSPECT CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

2.PERFORM ACTIVE TEST USING TECHSTREAM (AUTO LSD INDICATOR LIGHT)

B

2.PERFORM ACTIVE TEST USING TECHSTREAM (AUTO LSD INDICATOR LIGHT)
a.

Connect the Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the Techstream on.


d.

Select the Active Test mode and operate the AUTO LSD indicator light using the Techstream.

ABS/VSC/TRAC
Tester Display Test Part Control Range Diagnostic Note
Auto LSD Indicator Light AUTO LSD indicator light ON / OFF Observe combination meter


e.

Check that the AUTO LSD indicator light turns on and off in the combination meter when using the Techstream.

OK:

The AUTO LSD indicator light turns on and off in accordance with the Techstream operation.


HINT:

When the AUTO LSD indicator light remains illuminated, there may be an open in the wire harness of the combination meter or abnormalities in the meter circuit.




OK

3.INSPECT VSC OFF SWITCH

NG

3.INSPECT VSC OFF SWITCH
a.
C179171E01
0.25,0.044 2.740,0.380 2.489,0.336 10 Component without harness connected: (VSC OFF Switch) 0.517,2.848 1.183,3.021 0.666,0.174 10 : No pin

Remove the VSC OFF switch (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 - 9 Switch is pressed Below 1 Ω
Switch is not pressed 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)

NG

REPLACE VSC OFF SWITCH

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
a.
U152483E01
0.24,0.107 2.750,0.431 2.510,0.324 10 Front view of wire harness connector: (to Skid Control ECU) 0.182,0.961 0.452,1.133 0.270,0.172 10 A17 2.258,1.042 2.620,1.187 0.361,0.145 10 CSW 0.258,2.651 2.767,2.961 2.510,0.310 10 Front view of wire harness connector: (to VSC OFF Switch) 0.595,3.78 0.882,3.952 0.287,0.172 10 J22 2.471,1.574 2.471,1.251 false

Disconnect the A17 ECU connector.


b.

Disconnect the J22 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-4 (CSW) - J22-9 Always Below 1 Ω
A17-4 (CSW) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR