Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB2  Short to GND in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a ground short in the blind spot monitor indicator RH.

DTC Code DTC Detection Condition Trouble Area
C1AB2 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output from the blind spot monitor sensor to the indicator is low for a certain amount of time.
·

Harness or connector

·

Outer rear view mirror assembly RH

·

Outer rear view mirror sub-assembly RH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E221720E41
3.042,1.24 3.594,1.469 0.552,0.229 10 false BSR+ 0.865,2.167 1.198,2.323 0.333,0.156 10 false A 0.844,2.344 3.375,2.729 2.531,0.385 10 false Outer Rear View Mirror Sub-assembly RH (Blind Spot Monitor Indicator RH) 0.833,3.406 1.167,3.563 0.333,0.156 10 false M6 0.823,3.583 3.167,3.792 2.344,0.208 10 false Outer Rear View Mirror Assembly RH 5.531,3.385 5.865,3.542 0.333,0.156 10 false S6 5.531,3.563 6.719,3.906 1.188,0.344 10 false Blind Spot Monitor Sensor RH 2.552,1.25 2.76,1.427 0.208,0.177 10 false 7 2.375,1.344 2.521,1.5 0.146,0.156 10 false + 5.385,1.24 5.563,1.396 0.177,0.156 10 false 4 5.573,1.354 5.948,1.51 0.375,0.156 10 false OMIR 2.385,1.823 2.677,2.063 0.292,0.24 10 false - 2.552,1.719 2.729,1.875 0.177,0.156 10 false 5 3.521,1.24 4.198,1.438 0.677,0.198 10 false 9*1, 18*2 3.521,1.719 3.76,1.896 0.24,0.177 10 false 5 3.052,1.729 3.438,2.021 0.385,0.292 10 false MLP- 0.167,4.198 1.156,4.417 0.99,0.219 10 false *1: w/ Memory 0.167,4.427 1.156,4.646 0.99,0.219 10 false *2: w/o Memory

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH)
a.
U152846E02
2.427,1.188 2.563,0.948 2.563,0.948 2.719,0.948 true 2.406,1.521 2.542,1.792 2.542,1.792 2.698,1.792 true 0.094,0.063 0.375,0.313 0.281,0.25 10 false *a 1.635,0.281 1.917,0.531 0.281,0.25 10 false M6 2.75,0.875 3.313,1.125 0.563,0.25 10 false BSR+*A 2.74,1.708 3.302,1.958 0.563,0.25 10 false BSR+*B

Disconnect the outer rear view mirror assembly RH connector.


b.

Disconnect the S6 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Memory:
Tester Connection Condition Specified Condition
M6-9 (BSR+) - Body ground Always 10 kΩ or higher

w/o Memory:
Tester Connection Condition Specified Condition
M6-18 (BSR+) - Body ground Always 10 kΩ or higher


Text in Illustration
*A w/ Memory
*B w/o Memory
*a Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH)



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH)
a.
U152812E02
1.875,1.156 2.375,0.708 2.375,0.708 2.615,0.708 true 1.635,0.302 1.906,0.5 0.271,0.198 10 false S6 2.667,0.635 3.083,0.792 0.417,0.156 10 false OMIR 0.094,0.052 0.365,0.25 0.271,0.198 10 false *a

Disconnect the blind spot monitor sensor RH connector.


b.

Disconnect the A outer rear view mirror sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S6-4 (OMIR) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)



OK

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH
a.

Replace the outer rear view mirror sub-assembly RH with a new or normally functioning one (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Check for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH IS DEFECTIVE)

NG