Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB3  Short to GND in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a ground short in the blind spot monitor indicator LH.

DTC Code DTC Detection Condition Trouble Area
C1AB3 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the voltage output from the blind spot monitor sensor to the indicator is low for a certain amount of time.
·

Harness or connector

·

Outer rear view mirror assembly LH

·

Outer rear view mirror sub-assembly LH

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E221720E42
3.042,1.24 3.594,1.469 0.552,0.229 10 false BSL+ 0.865,2.167 1.198,2.323 0.333,0.156 10 false B 0.844,2.344 3.375,2.729 2.531,0.385 10 false Outer Rear View Mirror Sub-assembly LH (Blind Spot Monitor Indicator LH) 0.833,3.406 1.167,3.563 0.333,0.156 10 false N5 0.823,3.583 3.167,3.792 2.344,0.208 10 false Outer Rear View Mirror Assembly LH 5.531,3.385 5.865,3.542 0.333,0.156 10 false S5 5.531,3.563 6.719,3.906 1.188,0.344 10 false Blind Spot Monitor Sensor LH 2.552,1.25 2.76,1.427 0.208,0.177 10 false 7 2.375,1.344 2.521,1.5 0.146,0.156 10 false + 5.385,1.24 5.563,1.396 0.177,0.156 10 false 4 5.573,1.354 5.948,1.51 0.375,0.156 10 false OMIL 2.385,1.823 2.677,2.063 0.292,0.24 10 false - 2.552,1.719 2.729,1.875 0.177,0.156 10 false 5 3.521,1.24 4.198,1.438 0.677,0.198 10 false 9*1, 18*2 3.521,1.719 3.76,1.896 0.24,0.177 10 false 5 3.052,1.729 3.438,2.021 0.385,0.292 10 false MLP- 0.167,4.198 1.156,4.417 0.99,0.219 10 false *1: w/ Memory 0.167,4.427 1.156,4.646 0.99,0.219 10 false *2: w/o Memory

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH)
a.
U152845E02
2.406,1.167 2.542,0.927 2.542,0.927 2.698,0.927 true 2.406,1.51 2.542,1.781 2.542,1.781 2.698,1.781 true 0.094,0.052 0.375,0.302 0.281,0.25 10 false *a 1.635,0.281 1.917,0.531 0.281,0.25 10 false N5 2.729,0.844 3.292,1.094 0.563,0.25 10 false BSL+*A 2.74,1.698 3.302,1.948 0.563,0.25 10 false BSL+*B

Disconnect the outer rear view mirror assembly LH connector.


b.

Disconnect the S5 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Memory:
Tester Connection Condition Specified Condition
N5-9 (BSL+) - Body ground Always 10 kΩ or higher

w/o Memory:
Tester Connection Condition Specified Condition
N5-18 (BSL+) - Body ground Always 10 kΩ or higher


Text in Illustration
*A w/ Memory
*B w/o Memory
*a Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)



OK

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH)
a.
U152813E02
1.875,1.156 2.375,0.708 2.375,0.708 2.615,0.708 true 1.635,0.302 1.906,0.5 0.271,0.198 10 false S5 2.667,0.635 3.083,0.792 0.417,0.156 10 false OMIL 0.094,0.052 0.365,0.25 0.271,0.198 10 false *a

Disconnect the blind spot monitor sensor LH connector.


b.

Disconnect the B outer rear view mirror sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-4 (OMIL) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)



OK

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH
a.

Replace the outer rear view mirror sub-assembly LH with a new or normally functioning one (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH IS DEFECTIVE)

NG