Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB4  Open in Outer Mirror Indicator(Master)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects an open in the blind spot monitor indicator RH.

DTC Code DTC Detection Condition Trouble Area
C1AB4 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing to the indicator is below a specified value when indicator operation voltage is sent to the indicator.
·

Harness or connector

·

Outer rear view mirror sub-assembly RH

·

Outer rear view mirror assembly RH

·

Blind spot monitor sensor RH



WIRING DIAGRAM

E221720E41
3.042,1.24 3.594,1.469 0.552,0.229 10 false BSR+ 0.865,2.167 1.198,2.323 0.333,0.156 10 false A 0.844,2.344 3.375,2.729 2.531,0.385 10 false Outer Rear View Mirror Sub-assembly RH (Blind Spot Monitor Indicator RH) 0.833,3.406 1.167,3.563 0.333,0.156 10 false M6 0.823,3.583 3.167,3.792 2.344,0.208 10 false Outer Rear View Mirror Assembly RH 5.531,3.385 5.865,3.542 0.333,0.156 10 false S6 5.531,3.563 6.719,3.906 1.188,0.344 10 false Blind Spot Monitor Sensor RH 2.552,1.25 2.76,1.427 0.208,0.177 10 false 7 2.375,1.344 2.521,1.5 0.146,0.156 10 false + 5.385,1.24 5.563,1.396 0.177,0.156 10 false 4 5.573,1.354 5.948,1.51 0.375,0.156 10 false OMIR 2.385,1.823 2.677,2.063 0.292,0.24 10 false - 2.552,1.719 2.729,1.875 0.177,0.156 10 false 5 3.521,1.24 4.198,1.438 0.677,0.198 10 false 9*1, 18*2 3.521,1.719 3.76,1.896 0.24,0.177 10 false 5 3.052,1.729 3.438,2.021 0.385,0.292 10 false MLP- 0.167,4.198 1.156,4.417 0.99,0.219 10 false *1: w/ Memory 0.167,4.427 1.156,4.646 0.99,0.219 10 false *2: w/o Memory

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND)
a.

Disconnect the S6 blind spot monitor sensor RH connector.


b.

Disconnect the M6 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Memory:
Tester Connection Condition Specified Condition
S6-4 (OMIR) - M6-9 (BSR+) Always Below 1 Ω
M6-5 (MLP-) - Body ground Always Below 1 Ω

w/o Memory:
Tester Connection Condition Specified Condition
S6-4 (OMIR) - M6-18 (BSR+) Always Below 1 Ω
M6-5 (MLP-) - Body ground Always Below 1 Ω




OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
U152808E02
1.021,0.917 0.865,0.573 0.865,0.573 0.76,0.573 true 1.031,1.323 0.875,1.531 0.875,1.531 0.771,1.531 true 1.74,0.927 2.479,0.552 2.479,0.552 2.719,0.552 true 1.667,2.958 1.208,3.125 1.208,3.125 1.135,3.125 true 1.719,2.698 2.167,2.177 2.167,2.177 2.229,2.177 true 0.094,0.052 0.281,0.198 0.188,0.146 10 false *a 0.198,0.5 0.792,0.646 0.594,0.146 10 false BSR+*A 0.125,1.833 0.313,1.979 0.188,0.146 10 false *b 0.208,1.458 0.802,1.604 0.594,0.146 10 false BSR+*B 2.771,0.479 3.219,0.667 0.448,0.188 10 false MLP- 1.01,3.042 1.135,3.188 0.125,0.146 10 false + 2.292,2.083 2.417,2.229 0.125,0.146 10 false - 1.615,0.271 1.885,0.417 0.271,0.146 10 false M6 1.656,2 1.927,2.146 0.271,0.146 10 false A

Remove the outer rear view mirror assembly RH (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Remove the outer rear view mirror sub-assembly RH (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR GLASS>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Memory:
Tester Connection Condition Specified Condition
M6-9 (BSR+) - A-7 (+) Always Below 1 Ω
M6-5 (MLP-) - A-5 (-) Always Below 1 Ω

w/o Memory:
Tester Connection Condition Specified Condition
M6-18 (BSR+) - A-7 (+) Always Below 1 Ω
M6-5 (MLP-) - A-5 (-) Always Below 1 Ω


Text in Illustration
*A w/ Memory
*B w/o Memory
*a Vehicle Side
*b Outer Rear View Mirror Sub-assembly RH Side



OK

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH
a.

Replace the outer rear view mirror sub-assembly RH with a new or normally functioning one (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY RH IS DEFECTIVE)

NG