Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM27M0U _56 Audio / Visual / Telematics _049159 PARK ASSIST / MONITORING _0234450 BLIND SPOT MONITOR SYSTEM C

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  C1AB5  Open in Outer Mirror Indicator(Slave)  


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects an open in the blind spot monitor indicator LH.

DTC Code DTC Detection Condition Trouble Area
C1AB5 With the blind spot monitor main switch assembly (warning canceling switch assembly) on, the current flowing to the indicator is below a specified value when indicator operation voltage is sent to the indicator.
·

Harness or connector

·

Outer rear view mirror sub-assembly LH

·

Outer rear view mirror assembly LH

·

Blind spot monitor sensor LH



WIRING DIAGRAM

E221720E42
3.042,1.24 3.594,1.469 0.552,0.229 10 false BSL+ 0.865,2.167 1.198,2.323 0.333,0.156 10 false B 0.844,2.344 3.375,2.729 2.531,0.385 10 false Outer Rear View Mirror Sub-assembly LH (Blind Spot Monitor Indicator LH) 0.833,3.406 1.167,3.563 0.333,0.156 10 false N5 0.823,3.583 3.167,3.792 2.344,0.208 10 false Outer Rear View Mirror Assembly LH 5.531,3.385 5.865,3.542 0.333,0.156 10 false S5 5.531,3.563 6.719,3.906 1.188,0.344 10 false Blind Spot Monitor Sensor LH 2.552,1.25 2.76,1.427 0.208,0.177 10 false 7 2.375,1.344 2.521,1.5 0.146,0.156 10 false + 5.385,1.24 5.563,1.396 0.177,0.156 10 false 4 5.573,1.354 5.948,1.51 0.375,0.156 10 false OMIL 2.385,1.823 2.677,2.063 0.292,0.24 10 false - 2.552,1.719 2.729,1.875 0.177,0.156 10 false 5 3.521,1.24 4.198,1.438 0.677,0.198 10 false 9*1, 18*2 3.521,1.719 3.76,1.896 0.24,0.177 10 false 5 3.052,1.729 3.438,2.021 0.385,0.292 10 false MLP- 0.167,4.198 1.156,4.417 0.99,0.219 10 false *1: w/ Memory 0.167,4.427 1.156,4.646 0.99,0.219 10 false *2: w/o Memory

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor main switch assembly (warning canceling switch assembly) is on.


PROCEDURE

1.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

NG

2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND)
a.

Disconnect the S5 blind spot monitor sensor LH connector.


b.

Disconnect the N5 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Memory:
Tester Connection Condition Specified Condition
S5-4 (OMIL) - N5-9 (BSL+) Always Below 1 Ω
N5-5 (MLP-) - Body ground Always Below 1 Ω

w/o Memory:
Tester Connection Condition Specified Condition
S5-4 (OMIL) - N5-18 (BSL+) Always Below 1 Ω
N5-5 (MLP-) - Body ground Always Below 1 Ω




OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
U152809E02
1.021,0.917 0.865,0.646 0.865,0.646 0.76,0.646 true 1.031,1.323 0.875,1.479 0.875,1.479 0.771,1.479 true 1.74,0.917 2.375,0.656 2.375,0.656 2.615,0.656 true 1.677,2.958 1.219,3.125 1.219,3.125 1.146,3.125 true 1.729,2.688 2.177,2.167 2.177,2.167 2.24,2.167 true 0.094,0.052 0.281,0.198 0.188,0.146 10 false *a 0.208,0.583 0.802,0.729 0.594,0.146 10 false BSL+*A 0.135,1.833 0.323,1.979 0.188,0.146 10 false *b 0.24,1.417 0.833,1.563 0.594,0.146 10 false BSL+*B 2.688,0.583 3.094,0.729 0.406,0.146 10 false MLP- 1.021,3.042 1.146,3.188 0.125,0.146 10 false + 2.302,2.073 2.427,2.219 0.125,0.146 10 false - 1.646,0.271 1.917,0.417 0.271,0.146 10 false N5 1.656,2 1.927,2.146 0.271,0.146 10 false B

Remove the outer rear view mirror assembly LH (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR>REMOVAL).


b.

Remove the outer rear view mirror sub-assembly LH (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR GLASS>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Memory:
Tester Connection Condition Specified Condition
N5-9 (BSL+) - B-7 (+) Always Below 1 Ω
N5-5 (MLP-) - B-5 (-) Always Below 1 Ω

w/o Memory:
Tester Connection Condition Specified Condition
N5-18 (BSL+) - B-7 (+) Always Below 1 Ω
N5-5 (MLP-) - B-5 (-) Always Below 1 Ω


Text in Illustration
*A w/ Memory
*B w/o Memory
*a Vehicle Side
*b Outer Rear View Mirror Sub-assembly LH Side



OK

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

4.CHECK OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH
a.

Replace the outer rear view mirror sub-assembly LH with a new or normally functioning one (See page Vehicle Interior>MIRROR>OUTER REAR VIEW MIRROR GLASS>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR).

OK:

No DTCs are output.




OK

END (OUTER REAR VIEW MIRROR SUB-ASSEMBLY LH IS DEFECTIVE)

NG