for Double Cab, CrewMax
If the rear RH side manual UP/DOWN function does not operate, there may be a malfunction in the rear switch RH, rear motor RH, master switch or harness and connector.
Disconnect the O5 switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O5-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG
Remove the rear switch RH (see page Vehicle Interior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4 (U) - 3 (B) | UP | Below 1 Ω |
| 1 (D) - 2 (SD) | ||
| 4 (U) - 5 (SU) | OFF | Below 1 Ω |
| 1 (D) - 2 (SD) | ||
| 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
| 1 (D) - 3 (B) |
OK
NG
Disconnect the O5 switch connector.
Disconnect the O3 motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O5-1 (D) - O3-2 | Always | Below 1 Ω |
| O5-4 (U) - O3-1 | Always | Below 1 Ω |
| O5-1 (D) or O3-2 - Body ground | Always | 10 kΩ or higher |
| O5-4 (U) or O3-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O5-1 (D) - O3-1 | Always | Below 1 Ω |
| O5-4 (U) - O3-2 | Always | Below 1 Ω |
| O5-1 (D) or O3-1 - Body ground | Always | 10 kΩ or higher |
| O5-4 (U) or O3-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the rear motor RH (see page Vehicle Interior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL).
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 1
Battery negative (-) → 2 |
Motor gear rotates counterclockwise |
| Battery positive (+) → 2
Battery negative (-) → 1 |
Motor gear rotates clockwise |
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 1
Battery negative (-) → 2 |
Motor gear rotates clockwise |
| Battery positive (+) → 2
Battery negative (-) → 1 |
Motor gear rotates counterclockwise |
OK
NG
Disconnect the N2 master switch connector.
Disconnect the O5 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N2-10 (U) - O5-5 (SU) | Always | Below 1 Ω |
| N2-18 (D) - O5-2 (SD) | Always | Below 1 Ω |
| N2-10 (U) or O5-5 (SU) - Body ground | Always | 10 kΩ or higher |
| N2-18 (D) or O5-2 (SD) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the master switch (see page Vehicle Interior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).
Reconnect the master switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N2-10 (U) - N2-1 (E) | Ignition switch ON, rear RH switch of master switch OFF → UP | Below 1 V → 11 to 14 V |
| N2-18 (D) - N2-1 (E) | Ignition switch ON, rear RH switch of master switch OFF → DOWN |
OK
NG