Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234466 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

If the driver side manual UP/DOWN function does not operate, there may be a malfunction in master switch, driver side motor or harness and connector.


WIRING DIAGRAM

B442870E01
0.458,0.75 0.688,0.917 0.229,0.167 10 false N3 0.448,0.917 2.344,1.302 1.896,0.385 10 false Front Power Window Regulator Motor Assembly LH 3.563,0.698 3.708,0.865 0.146,0.167 10 false 2 3.563,1.021 3.708,1.188 0.146,0.167 10 false 1 4.156,0.698 5.01,0.885 0.854,0.188 10 false 10*1, 3*2, 3*3 4.146,0.99 5,1.177 0.854,0.188 10 false 12*1, 4*2, 4*3 2.073,1.708 2.865,1.917 0.792,0.208 10 false from Battery 4.167,1.563 5.021,1.75 0.854,0.188 10 false 15*1, 6*2, 6*3 4.208,2.146 5.021,2.323 0.813,0.177 10 false 7*1, 1*2, 1*3 5.198,0.833 5.344,1 0.146,0.167 10 false U 5.198,1.125 5.344,1.292 0.146,0.167 10 false D 5.208,1.719 5.354,1.885 0.146,0.167 10 false B 5.208,2.292 5.354,2.458 0.146,0.167 10 false E 2.74,2.302 3.74,2.51 1,0.208 10 false to Body Ground 0.167,2.823 1.344,3.01 1.177,0.188 10 false *1: for Regular Cab 0.188,3.417 1.188,3.625 1,0.208 10 false *3: for CrewMax 0.177,3.104 1.302,3.302 1.125,0.198 10 false *2: for Double Cab 5.156,2.938 5.385,3.104 0.229,0.167 10 false N2 5.156,3.125 6.75,3.469 1.594,0.344 10 false Power Window Regulator Master Switch Assembly

PROCEDURE

1.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.
B231474E03
1.349,1.988 0.691,0.955 0.691,0.955 0.858,0.955 false 0.884,0.882 1.623,1.034 0.739,0.152 10 Motor Gear 1.909,2.952 2.589,3.098 0.680,0.145 10 Clockwise 1.952,1.993 3.073,2.138 1.121,0.145 10 Counterclockwise 0.046,0.05 2.707,0.494 2.661,0.445 10 Component without harness connected: (Driver Side Motor)

Remove the motor (see page Vehicle Interior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).


b.

Apply battery voltage to connector terminals 1 and 2.


c.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Motor gear rotates counterclockwise
Battery positive (+) → 2
Battery negative (-) → 1
Motor gear rotates clockwise




OK

2.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

2.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)
U151867E02
1.969,1.885 2.063,1.594 false 1.542,1.427 1.813,1.552 false 2.01,1.396 1.396,1.104 false 2.198,1.438 2.635,1.875 false 1.073,0.063 3.365,0.427 2.292,0.365 10 false Front view of wire harness connector: (to Master Switch) 4.156,0.063 6.438,0.448 2.281,0.385 10 false Front view of wire harness connector: (to Driver Side Motor) 2.198,0.76 2.406,0.906 0.208,0.146 10 false N2 5.177,0.792 5.375,0.948 0.198,0.156 10 false N3 1.854,1.906 2.104,2.063 0.25,0.156 10 false D*1 2.625,1.906 3.208,2.063 0.583,0.156 10 false D*2, *3 1.26,1.344 1.51,1.5 0.25,0.156 10 false U*1 0.063,1.927 1.51,2.083 1.448,0.156 10 false *1: for Regular Cab 0.063,2.198 1.615,2.354 1.552,0.156 10 false *2: for Double Cab 0.063,2.458 1.406,2.615 1.344,0.156 10 false *3: for CrewMax 0.917,1 1.427,1.156 0.51,0.156 10 false U*2, *3

a.

Disconnect the N2 master switch connector.


b.

Disconnect the N3 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Regular Cab:
Tester Connection Condition Specified Condition
N2-10 (U) - N3-2 Always Below 1 Ω
N2-12 (D) - N3-1 Always Below 1 Ω
N2-10 (U) or N3-2 - Body ground Always 10 kΩ or higher
N2-12 (D) or N3-1 - Body ground Always 10 kΩ or higher

for Double Cab:
Tester Connection Condition Specified Condition
N2-3 (U) - N3-2 Always Below 1 Ω
N2-4 (D) - N3-1 Always Below 1 Ω
N2-3 (U) or N3-2 - Body ground Always 10 kΩ or higher
N2-4 (D) or N3-1 - Body ground Always 10 kΩ or higher

for CrewMax:
Tester Connection Condition Specified Condition
N2-3 (U) - N3-2 Always Below 1 Ω
N2-4 (D) - N3-1 Always Below 1 Ω
N2-3 (U) or N3-2 - Body ground Always 10 kΩ or higher
N2-4 (D) or N3-1 - Body ground Always 10 kΩ or higher




OK

3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
U151909E01
1.233,1.431 1.704,1.21 false 3.317,1.355 4.582,1.525 1.265,0.170 10 Driver Side Switch 0.039,1.369 1.303,1.539 1.265,0.170 10 Driver Side Switch 4.601,1.408 5.043,1.163 false 3.639,0.122 6.476,0.370 2.837,0.248 12 for Double Cab, CrewMax: 0.25,0.122 1.573,0.333 1.323,0.211 12 for Regular Cab: 4.022,2.333 6.630,2.674 2.608,0.341 10 Component with harness connected: (Master Switch) 0.367,2.333 2.974,2.674 2.607,0.341 10 Component with harness connected: (Master Switch) 2.1,4.059 2.299,4.222 0.200,0.163 10 E 4.323,3.695 4.468,3.858 0.144,0.163 10 E 4.585,4.025 4.765,4.187 0.179,0.163 10 U 4.86,4.11 5.128,4.273 0.268,0.163 10 D 0.641,3.722 0.915,3.884 0.274,0.163 10 U 1.026,4.101 1.321,4.264 0.295,0.163 10 D 2.112,4.053 1.828,3.588 false 4.924,4.097 5.193,3.586 false 1.109,3.465 0.754,3.719 false 1.354,3.47 1.121,4.092 false 4.827,3.553 4.456,3.74 false 4.681,4.015 5.072,3.569 false 0.47,3.317 0.716,3.473 0.246,0.156 10 N2 4.15,3.317 4.396,3.473 0.246,0.156 10 N2


b.

Reconnect the master switch connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Regular Cab:
Tester Connection Condition Specified Condition
N2-10 (U) - N2-7 (E) Ignition switch ON, driver side switch of master switch OFF → UP Below 1 V → 11 to 14 V
N2-12 (D) - N2-7 (E) Ignition switch ON, driver side switch of master switch OFF → DOWN Below 1 V → 11 to 14 V
N2-12 (D) - N2-7 (E) Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open Below 1 V → 11 to 14 V → Below 1 V

for Double Cab:
Tester Connection Condition Specified Condition
N2-3 (U) - N2-1 (E) Ignition switch ON, driver side switch of master switch OFF → UP Below 1 V → 11 to 14 V
N2-4 (D) - N2-1 (E) Ignition switch ON, driver side switch of master switch OFF → DOWN Below 1 V → 11 to 14 V
N2-4 (D) - N2-1 (E) Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open Below 1 V → 11 to 14 V → Below 1 V

for CrewMax:
Tester Connection Condition Specified Condition
N2-3 (U) - N2-1 (E) Ignition switch ON, driver side switch of master switch OFF → UP Below 1 V → 11 to 14 V
N2-4 (D) - N2-1 (E) Ignition switch ON, driver side switch of master switch OFF → DOWN Below 1 V → 11 to 14 V
N2-4 (D) - N2-1 (E) Ignition switch ON, driver side door glass fully closed → power window AUTO DOWN operation → driver side door glass fully open Below 1 V → 11 to 14 V → Below 1 V




OK

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY