If the front passenger side manual UP/DOWN function does not operate, there may be a malfunction in the power window regulator switch assembly, front passenger side motor, master switch or harness and connector.
Disconnect the M2 switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M2-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
OK
NG
Remove the power window regulator switch assembly (see page Vehicle Interior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 4 (U) - 3 (B) | UP | Below 1 Ω |
| 1 (D) - 2 (SD) | ||
| 4 (U) - 5 (SU) | OFF | Below 1 Ω |
| 1 (D) - 2 (SD) | ||
| 4 (U) - 5 (SU) | DOWN | Below 1 Ω |
| 1 (D) - 3 (B) |
OK
NG
Disconnect the M2 switch connector.
Disconnect the M3 motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-1 (D) - M3-1 | Always | Below 1 Ω |
| M2-4 (U) - M3-2 | Always | Below 1 Ω |
| M2-1 (D) or M3-1 - Body ground | Always | 10 kΩ or higher |
| M2-4 (U) or M3-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front passenger side motor (see page Vehicle Interior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).
Apply battery voltage to connector terminals 1 and 2.
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 1
Battery negative (-) → 2 |
Motor gear rotates clockwise |
| Battery positive (+) → 2
Battery negative (-) → 1 |
Motor gear rotates counterclockwise |
OK
NG
Disconnect the N2 master switch connector.
Disconnect the M2 switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N2-16 (U) - M2-5 (SU) | Always | Below 1 Ω |
| N2-18 (D) - M2-2 (SD) | Always | Below 1 Ω |
| N2-16 (U) or M2-5 (SU) - Body ground | Always | 10 kΩ or higher |
| N2-18 (D) or M2-2 (SD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N2-16 (U) - M2-5 (SU) | Always | Below 1 Ω |
| N2-15 (D) - M2-2 (SD) | Always | Below 1 Ω |
| N2-16 (U) or M2-5 (SU) - Body ground | Always | 10 kΩ or higher |
| N2-15 (D) or M2-2 (SD) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N2-16 (U) - M2-5 (SU) | Always | Below 1 Ω |
| N2-15 (D) - M2-2 (SD) | Always | Below 1 Ω |
| N2-16 (U) or M2-5 (SU) - Body ground | Always | 10 kΩ or higher |
| N2-15 (D) or M2-2 (SD) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the master switch (see page Vehicle Interior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).
Reconnect the master switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N2-16 (U) - N2-7 (E) | Ignition switch ON, front passenger side switch of master switch OFF → UP | Below 1 V → 11 to 14 V |
| N2-18 (D) - N2-7 (E) | Ignition switch ON, front passenger side switch of master switch OFF → DOWN |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N2-16 (U) - N2-1 (E) | Ignition switch ON, front passenger side switch of master switch OFF → UP | Below 1 V → 11 to 14 V |
| N2-15 (D) - N2-1 (E) | Ignition switch ON, front passenger side switch of master switch OFF → DOWN |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N2-16 (U) - N2-1 (E) | Ignition switch ON, front passenger side switch of master switch OFF → UP | Below 1 V → 11 to 14 V |
| N2-15 (D) - N2-1 (E) | Ignition switch ON, front passenger side switch of master switch OFF → DOWN |
OK
NG