Home › Vehicle Interior › WINDOW / GLASS › BACK WINDOW GLASS(for Regular Cab and Double Cab)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234467 BACK WINDOW GLASS(for Regular Cab and Double Cab) A

WINDOW / GLASS  BACK WINDOW GLASS(for Regular Cab and Double Cab)  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 2.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 3.REMOVE FRONT SEAT ASSEMBLY (for Center Seat)

Hide 4.REMOVE REAR SEAT ASSEMBLY (for Double Cab)

Hide 67918B 7.REMOVE REAR DOOR SCUFF PLATE LH (for Double Cab)

Hide 67917B 8.REMOVE REAR DOOR SCUFF PLATE RH (for Double Cab)

Hide 62312B 9.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)

a.

Partially remove the front door opening trim weatherstrip LH so that the quarter trim panel front LH and quarter trim panel lower LH can be removed (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).


Hide 62311B 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)

HINT:

Use the same procedures described for the LH side.


Hide 62332A 11.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab)

a.

Partially remove the front door opening trim weatherstrip LH so that the quarter trim panel front LH and quarter trim panel lower LH can be removed (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).


Hide 62331A 12.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab)

HINT:

Use the same procedures described for the LH side.


Hide 64261C 13.REMOVE UPPER BACK PANEL GARNISH (for Regular Cab)

Hide 64439D 14.REMOVE LUGGAGE COMPARTMENT BOX LH (for Regular Cab)

Hide 64429E 15.REMOVE LUGGAGE COMPARTMENT BOX RH (for Regular Cab)

Hide 62540 16.REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH

a.

for Regular Cab:

Remove the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).


b.

for Double Cab:

Remove the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).


Hide 62530 17.REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH

a.

for Regular Cab:

Remove the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).


b.

for Double Cab:

Remove the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).


Hide 62520P 18.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

a.

for Regular Cab:

Remove the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL).


b.

for Double Cab:

Remove the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL).


Hide 62510P 19.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 81240 20.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 64141H 22.REMOVE NO. 1 BACK PANEL SILENCER (for Power Slide Type)

B227085

a.

Using a clip remover, remove the 4 clips and No. 1 back panel silencer.


Hide 69088A 23.REMOVE DOOR WINDOW REGULATOR CABLE SUB-ASSEMBLY (for Power Slide Type)

a.

Using a clip remover, detach the 6 clips labeled A in the illustration.


b.

Compress the springs to release the tension in the cables, and then disconnect the wire ends from the back window shown in the illustration labeled B.


c.

Pull out the wires from the back window shown in the illustration labeled C.

B227086E07
4,0.667 3.927,0.667 3.927,0.667 3.479,1.792 false 5.302,1.958 4.885,0.646 4.885,0.646 4.719,0.646 false 0.688,6.719 0.865,7.302 0.865,7.302 1.208,7.302 false 6.573,6.792 6.438,7.323 6.438,7.323 6.135,7.323 false 1.51,4.396 1.896,5.354 1.896,5.354 2.302,4.583 false 2.875,4.583 1.896,5.354 false 6.198,4.417 5.396,5.344 5.396,5.344 5.406,4.583 false 5.396,5.344 4.906,4.563 false 3.417,0.979 3.563,1.156 0.146,0.177 10 false B 5.573,1.104 5.708,1.292 0.135,0.188 10 false B 1.792,5.771 1.948,5.969 0.156,0.198 10 false C 5.385,5.781 5.542,5.958 0.156,0.177 10 false C 1.833,5.385 1.979,5.531 0.146,0.146 10 false A 5.344,5.385 5.49,5.531 0.146,0.146 10 false A 4.083,0.563 4.75,0.76 0.667,0.198 10 false Wire End 5.188,7.25 6.083,7.427 0.896,0.177 10 false Back Window 1.24,7.24 2.135,7.417 0.896,0.177 10 false Back Window


d.
B227088

Remove the 2 bolts.


e.

Detach the claw and remove the door window regulator cable sub-assembly.


Hide 69811D 24.REMOVE DOOR WINDOW REGULATOR BASE PLATE (for Power Slide Type)

B227087

a.

Remove the 3 nuts and door window regulator base plate.


Hide 85710J 25.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Power Slide Type)

B227089

a.

Using a T25 "TORX" socket, remove the 3 screws and power window regulator motor.


Hide 64811 26.REMOVE BACK WINDOW GLASS

HINT:

Perform these procedures only when replacing the back window glass.


a.

Using a T10 "TORX" driver, remove the screw and stopper (illustration A).


b.

Slightly pull up the seal (arrow 1), and then pull out the seal from the channel in the direction of arrow 2.


c.

Slide the back window glass towards the LH side (arrow 3). Lower the back window glass into the channel and tilt it (arrow 4) to detach the upper part of the back window glass from the upper channel. Then remove the back window glass (arrow 5).

B231498E03
1.958,4.063 1.698,4.219 1.698,4.219 1.698,4.479 false 5.708,5.833 5.583,5.698 5.583,5.698 5.479,5.698 false 4.385,4.656 3.813,5.813 3.813,5.813 3.375,5.813 false 5.906,5.375 6.042,5.531 0.135,0.156 10 false A 6.563,3.5 6.667,3.656 0.104,0.156 10 false 1 6.938,3.094 7.073,3.271 0.135,0.177 10 false 2 4.865,2.354 4.979,2.5 0.115,0.146 10 false 3 5.885,2.281 6.01,2.469 0.125,0.188 10 false 4 4.271,2.198 4.385,2.417 0.115,0.219 10 true B 4.26,2.917 4.385,3.094 0.125,0.177 10 false B 0.771,4.854 1.292,5.063 0.521,0.208 10 false B - B 1.583,4.479 1.927,4.677 0.344,0.198 10 false Seal 4.958,5.604 5.469,5.823 0.51,0.219 10 false Stopper 1.719,5.729 3.406,6.104 1.688,0.375 10 false Back Window Glass with Back Door Glass Channel 5.75,2.677 5.875,2.865 0.125,0.188 10 false 5


Hide 63310 27.TEMPORARILY REMOVE ROOF HEADLINING ASSEMBLY

a.

for Regular Cab:

It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>REMOVAL) so that the back window glass can be removed in a later step.


b.

for Double Cab:

It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>REMOVAL) so that the back window glass can be removed in a later step.


Hide 75554A 28.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH

Hide 75553A 29.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:

Use the same procedures described for the LH side.


Hide 64810 30.REMOVE BACK WINDOW ASSEMBLY

B166482E02
1.354,0.708 1,0.708 1,0.708 1,0.583 false 1.406,0.615 2.396,0.813 0.99,0.198 10 false Protective Tape

a.

Apply protective tape to the outer surface of the vehicle body to prevent scratches.


b.
B166483E02
0.635,3.146 0.125,3.146 0.125,3.146 0.125,4.021 false 1.625,2.438 1.26,2.438 1.26,2.438 1.26,2.771 false 0.51,3.677 0.125,3.677 false 2.792,3.125 3.219,3.125 3.219,3.125 3.219,4 false 2.896,3.677 3.219,3.677 false 2.885,4.031 3.385,4.229 0.5,0.198 10 false Spacer 0.063,4.052 0.563,4.24 0.5,0.188 10 false Spacer 1.635,2.344 2.365,2.542 0.729,0.198 10 false Piano Wire

From the interior, insert a piano wire between the vehicle body and back window as shown in the illustration.


c.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.


d.
B166484E02
1.667,0.823 1.156,0.823 1.156,0.823 1.156,1.479 false 1.677,1.083 1.146,1.083 false 0.729,1.49 1.615,1.823 0.885,0.333 10 true Matchmark

Place matchmarks over the window and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks do not need to be placed if the window is not going to be reused.



e.

Cut through the adhesive by pulling the piano wire around the back window.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the back window.



f.
B166485

Using suction cups, remove the back window glass.

NOTICE:

If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.



Hide 75571G 31.REMOVE UPPER OUTSIDE BACK WINDOW MOULDING (for Slide Type, for Power Slide Type)

B166492E01
1.536,0.407 2.951,0.625 1.415,0.218 10 Double-sided Tape 1.484,0.487 1.249,0.487 1.249,0.487 1.249,0.986 false

HINT:

Perform the following procedure if replacing the back window moulding.


a.

Using a moulding remover, detach the 3 clips and remove the back window moulding.


Hide 75575E 32.REMOVE LOWER OUTSIDE BACK WINDOW MOULDING (for Slide Type, for Power Slide Type)

B166493E03
1.396,1.135 1.396,1.552 false 0.844,1.583 2.052,1.771 1.208,0.188 10 false Double-sided Tape

HINT:

Perform the following procedure if replacing the back window moulding.


a.

Using a moulding remover, detach the 3 clips and remove the back window moulding.


Hide 64810 33.CLEAN BACK WINDOW ASSEMBLY

a.

Using a scraper, remove the damaged spacers and adhesive sticking to the glass.


b.
B106929

Clean the outer edge of the back window with a non-residue solvent.

NOTICE:
·

Do not touch the back window surface after cleaning it.

·

Be careful not to damage the window.

·

Even if using a new back window, clean the back window with a non-residue solvent.




Hide 34.CLEAN VEHICLE BODY

B106081E11
0.377,0.027 1.012,0.204 0.635,0.177 10 Adhesive 1.949,0.07 2.585,0.246 0.635,0.177 10 Adhesive 0.514,1.29 0.11,0.113 0.11,0.113 0.257,0.113 false 2.302,1.428 1.589,0.156 1.589,0.156 1.846,0.156 false

a.

Using a scraper, remove the moulding and adhesive from the vehicle body.


b.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.



ii.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.




Hide 69957 35.REMOVE BACK DOOR GLASS CHANNEL