Home › Vehicle Interior › INTERIOR › ROOF HEADLINING(for Double Cab)
RM27M0U _58 Vehicle Interior _049165 INTERIOR _0234502 ROOF HEADLINING(for Double Cab) A

INTERIOR  ROOF HEADLINING(for Double Cab)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

Hide 4.REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

Hide 5.REMOVE FRONT SEAT ASSEMBLY (for Center Seat)

Hide 67914 7.REMOVE FRONT DOOR SCUFF PLATE LH

B165841

a.

Detach the 6 claws and 3 clips, and remove the front door scuff plate LH.


Hide 67913 8.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 67918B 9.REMOVE REAR DOOR SCUFF PLATE LH

B165842

a.

Detach the 6 claws and 2 clips, and remove the rear door scuff plate LH.


Hide 67917B 10.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62112 11.REMOVE COWL SIDE TRIM BOARD LH

B165704

a.

Remove the nut.


b.

Detach the 2 clips and remove the cowl side trim board LH.


Hide 62111C 12.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.


Hide 62312B 13.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the front door opening trim weatherstrip LH.


Hide 62311B 14.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62332A 15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the rear door opening trim weatherstrip LH.


Hide 62331A 16.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 62212 17.REMOVE FRONT PILLAR GARNISH LH

a.
B355361E01
2.234,1.328 2.425,1.495 0.191,0.167 10 *1 2.196,1.423 1.822,1.423 1.822,1.423 1.527,1.061 false 1.822,1.423 1.924,1.107 false

Apply protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a screwdriver, detach the claw and open the cover.

HINT:

Tape the screwdriver tip before use.



c.
B355363

Remove the bolt.


d.

Detach the clip and remove the front pillar garnish LH.


e.

Protect the curtain shield airbag assembly.

i.
B165709E08
2.042,0.333 1.906,0.333 1.906,0.333 1.646,0.646 false 2.469,0.792 2.281,0.792 2.281,0.792 1.844,1.292 false 0.521,2.115 0.521,1.844 0.521,1.844 1.208,1.156 false 2.5,0.698 2.698,0.885 0.198,0.188 10 false *2 2.073,0.24 2.271,0.406 0.198,0.167 10 false *1 0.448,2.156 0.646,2.344 0.198,0.188 10 false *3

Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish LH is removed.


Text in Illustration
*1 Adhesive Tape
*2 Protective Cover
*3 Curtain Shield Airbag Assembly



Hide 62211 18.REMOVE FRONT PILLAR GARNISH RH

a.
B355364E02
1.771,2.813 1.167,2.76 false 1.417,2.563 1.573,2.802 false 1.792,2.729 2.042,2.948 0.25,0.219 10 false *1

Apply protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a screwdriver, detach the 2 claws and open the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



c.
B355366

Remove the 2 bolts and front assist grip sub-assembly from the front pillar garnish RH.


d.
B355367

Detach the clip and remove the front pillar garnish RH.


e.

Protect the curtain shield airbag assembly.

i.

Completely cover the curtain shield airbag assembly with a cloth or nylon sheet and secure the ends of the cover with adhesive tape.

NOTICE:

Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.




Hide 62414A 19.REMOVE LOWER CENTER PILLAR GARNISH LH

B165827

a.

Detach the 2 claws and remove the cover.


b.
B165828

Loosen the bolt and disconnect the front seat outer belt assembly LH.


c.
B165829

Detach the 7 clips and 2 claws, and remove the lower center pillar garnish LH.


Hide 62413A 20.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 62412 21.REMOVE CENTER PILLAR GARNISH LH

a.

Using a screwdriver, detach the 2 claws and open the 2 assist grip covers.

HINT:

Tape the screwdriver tip before use.



b.

Remove the 2 bolts and rear assist grip assembly from the center pillar garnish LH.


c.

Remove the bolt.


d.

Detach the clip, guide and remove the center pillar garnish LH.

B355479E01
0.117,0.34 0.314,0.509 0.197,0.170 10 *1 0.282,0.414 0.438,0.414 0.438,0.414 0.539,0.789 false

Text in Illustration
*1 Protective Tape - -


e.

Pass the front seat outer belt assembly LH through the hole of the center pillar garnish LH.


Hide 62411 22.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 73024 23.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B165848

a.

Detach the 6 claws of the front shoulder belt anchor plate sub-assembly LH, and slide the front shoulder belt anchor plate sub-assembly LH in the direction of the arrow to remove it.


Hide 73023 24.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62540 25.REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH

a.
B165830

Detach the 2 claws and remove the cover.


b.
B165831

Loosen the bolt and disconnect the rear seat outer belt assembly.


c.
B165832

Detach the 6 clips and remove the lower quarter trim panel assembly LH.


Hide 62530 26.REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62520P 27.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

a.
B356805E01
0.877,0.992 1.060,1.146 0.184,0.154 10 *1 1.066,1.073 1.378,1.073 false 1.212,1.073 1.21,0.664 false

Apply protective tape as shown in the illustration.

Text in Illustration
*1 Protective Tape


b.

Using a screwdriver, detach the claw and open the cover.

HINT:

Tape the screwdriver tip before use.



c.
B356807

Remove the 2 bolts.


d.

Detach the 4 clips and remove the front quarter trim panel assembly LH.


e.

Pass the rear seat outer belt assembly through the hole of the front quarter trim panel assembly LH.


Hide 62510P 28.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 63650A 29.REMOVE ROOF CONSOLE BOX ASSEMBLY

Hide 87834 30.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 81240 31.REMOVE ROOM LIGHT ASSEMBLY

Hide 74320 32.REMOVE VISOR ASSEMBLY LH

B355481

a.

Remove the 2 screws.


b.

Detach the claw and remove the visor assembly LH.


c.
B355482

w/ Vanity Light:

Disconnect the connector.


Hide 74310 33.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74348 34.REMOVE VISOR HOLDER

HINT:

Use the same procedure to remove the visor holder on the other side.


a.
B165713

Using a T20 "TORX" driver, remove the "TORX" screw and visor holder.


Hide 74610A 36.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all the assist grip sub-assemblies.


a.
B155751E12
1.281,0.719 1.542,0.719 1.542,0.719 1.656,0.552 true 1.115,0.625 1.281,0.813 0.167,0.188 10 false *1

Using a screwdriver, detach the 2 claws and remove the assist grip cover.

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure to remove the assist grip cover on the other side.



Text in Illustration
*1 Protective Tape


b.

Detach the 2 clips and remove the assist grip sub-assembly.


Hide 74631C 37.REMOVE COAT HOOK

HINT:

Use the same procedure to remove the coat hook on the other side.


a.
B168149E03
1.384,0.864 1.575,1.045 0.191,0.181 10 *1 2.009,0.625 1.677,0.957 false 1.677,0.957 1.58,0.957 false

Using a screwdriver, detach the 2 claws and remove the coat hook cap.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



b.

Detach the clip and remove the coat hook.


Hide 63310 38.REMOVE ROOF HEADLINING ASSEMBLY

a.
B167283

w/ EC Mirror:

Disconnect the connector.


b.
B355487

Disconnect the connector and detach the 4 wire harness clamps from the front pillar LH.


c.
B355486

Detach the 4 clips and remove the roof headlining assembly.


d.
B355488

Take out the roof headlining assembly from the cabin as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when taking it out.