Use the same procedure for the LH side and RH side.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
85720A
1.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Apply MP grease to the sliding and rotating areas of the regulator motor.
Using a T25 ''TORX'' driver, install the motor with the 3 screws.
For a new rear window regulator, the installation position of the regulator will be set when the self-tapping screws are installed.
69804
2.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
for Double Cab:
Install the rear door window regulator sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door window regulator sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
68104
3.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH
for Double Cab:
Install the rear door glass sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door glass sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
67408F
4.INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
for Double Cab:
Install the rear door rear lower window frame sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door rear lower window frame sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
68152C
5.INSTALL REAR DOOR GLASS RUN LH
for Double Cab:
Install the rear door glass run LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door glass run LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
67842E
6.INSTALL REAR DOOR SERVICE HOLE COVER LH
for Double Cab:
Install the rear door service hole cover LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door service hole cover LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
67626C
7.INSTALL REAR NO. 2 DOOR TRIM BRACKET
for Double Cab:
Install the rear No. 2 door trim bracket (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear No. 2 door trim bracket (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
67604
8.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
for Double Cab:
Install the rear door trim board sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door trim board sub-assembly LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
67674A
9.INSTALL REAR DOOR FRAME GARNISH LH
for Double Cab:
Install the rear door frame garnish LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door frame garnish LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
74272A
10.INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH
for Double Cab:
Install the rear upper door armrest base panel LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear upper door armrest base panel LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
69284D
11.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH
for Double Cab:
Install the rear door inside handle bezel plug LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for Double Cab)>REASSEMBLY).
for CrewMax:
Install the rear door inside handle bezel plug LH (See page Vehicle Interior>ENGINE HOOD / DOOR>REAR DOOR(for CrewMax)>REASSEMBLY).
12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).