Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234473 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual UP/DOWN function does not operate, there may be a malfunction in the master switch, the driver side motor, or the harness or connector.


WIRING DIAGRAM

B231366E03
0.625,0.969 1.448,1.167 0.823,0.198 10 false from Battery 1.917,1.167 2.51,1.49 0.594,0.323 10 false POWER No. 3 0.24,2.552 1.917,2.927 1.677,0.375 10 false from Main Body ECU (Driver Side Junction Block) 0.656,3.438 1.688,3.656 1.031,0.219 10 false from P/W Relay 0.708,5.333 2.385,5.5 1.677,0.167 10 false : LIN Communication Line 2.75,2.365 2.844,2.531 0.094,0.167 10 false 6 2.958,2.5 3.281,2.656 0.323,0.156 10 false LIN1 3.615,2.5 3.948,2.656 0.333,0.156 10 false LIN2 2.99,1.99 3.115,2.156 0.125,0.167 10 false B 2.708,3.323 2.885,3.479 0.177,0.156 10 false 13 2.979,3.448 3.104,3.604 0.125,0.156 10 false B 2.75,1.906 2.865,2.052 0.115,0.146 10 false 3 3.667,2.99 3.896,3.146 0.229,0.156 10 false UP 4.021,2.865 4.125,3.031 0.104,0.167 10 false 4 3.438,3.417 3.906,3.573 0.469,0.156 10 false DOWN 4.021,3.323 4.135,3.479 0.115,0.156 10 false 5 3.781,3.833 3.906,3.99 0.125,0.156 10 false E 4.01,3.729 4.125,3.885 0.115,0.156 10 false 1 5.625,3.813 5.969,3.969 0.344,0.156 10 false GND 5.375,3.729 5.479,3.896 0.104,0.167 10 false 1 5.615,3.406 6.115,3.573 0.5,0.167 10 false DOWN 5.354,3.323 5.479,3.479 0.125,0.156 10 false 7 5.302,2.844 5.5,3.021 0.198,0.177 10 false 10 5.625,2.948 5.875,3.115 0.25,0.167 10 false UP 5.604,2.479 5.833,2.635 0.229,0.156 10 false LIN 5.375,2.365 5.49,2.521 0.115,0.156 10 false 9 5.625,0.948 5.76,1.104 0.135,0.156 10 false B 5.354,0.854 5.469,1.01 0.115,0.156 10 false 2 2.729,4.802 4.333,5.146 1.604,0.344 10 false Power Window Regulator Master Switch Assembly 5.146,4.76 7.115,5.198 1.969,0.438 10 false Front Power Window Regulator Motor Assembly LH 2.74,4.604 2.969,4.76 0.229,0.156 10 false N2 5.146,4.583 5.51,4.76 0.365,0.177 10 false N12 4.021,2.354 4.125,2.51 0.104,0.156 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK LIN COMMUNICATION SYSTEM
a.

Check for LIN communication system DTCs related to the power window control system (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

LIN communication system DTCs are not output.




OK

2.CHECK FOR DTC (B2312)

NG

2.CHECK FOR DTC (B2312)
a.

Check if DTC B2312 is output (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR).

OK:

DTC B2312 is not output.




OK

3.READ VALUE USING TECHSTREAM (DRIVER SIDE MOTOR)

NG

3.READ VALUE USING TECHSTREAM (DRIVER SIDE MOTOR)
a.

Use the Data List to check if the driver side motor is functioning properly.

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver side power window MANUAL UP switch signal / ON or OFF ON: Driver side switch operated
OFF: Driver side switch not operated
-
D Door P/W Down SW Driver side power window MANUAL DOWN switch signal / ON or OFF ON: Driver side switch operated
OFF: Driver side switch not operated
-


OK:

The Techstream display changes normally when master switch is operated.



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - BATTERY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - BATTERY AND BODY GROUND)
a.
U151988E02
1.292,2.063 1.146,2.76 false 1.531,2.323 1.698,2.781 false 0.885,2.031 0.458,2.51 false 0.385,0.021 2.75,0.51 2.365,0.49 10 false Front view of wire harness connector: (to Master Switch) 1.01,2.781 1.156,2.938 0.146,0.156 10 false B 1.75,2.802 1.896,2.969 0.146,0.167 10 false B 0.271,2.531 0.427,2.688 0.156,0.156 10 false E 0.229,1.698 0.448,1.875 0.219,0.177 10 false N2

Disconnect the N2 master switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
N2-3 (B) - Body ground Always 11 to 14 V
N2-13 (B) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
N2-1 (E) - Body ground Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE MOTOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE MOTOR - BATTERY AND BODY GROUND)
a.
U151989E01
0.261,0.038 2.738,0.572 2.477,0.534 10 Front view of wire harness connector: (to Driver Side Motor) 0.69,2.124 1.040,2.281 0.350,0.157 10 GND 2.344,2.195 2.465,2.365 0.121,0.169 10 B 1.531,1.814 1.129,2.166 false 1.896,1.822 2.297,2.223 false 0.566,1.616 0.883,1.774 0.317,0.158 10 N12

Disconnect the N12 motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N12-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (GND) - Body ground Always Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER SIDE MOTOR)
a.
U151995E01
0.29,0.185 2.646,0.693 2.356,0.508 10 Front view of wire harness connector: (to Master Switch) 0.205,2.499 2.562,3.007 2.356,0.508 10 Front view of wire harness connector: (to Driver Side Motor) 0.547,1.942 0.779,2.082 0.232,0.139 10 UP 2.713,2.018 3.172,2.170 0.459,0.152 10 DOWN 1.569,1.788 0.847,2.017 false 1.77,1.805 2.661,2.091 false 2.461,4.3 2.693,4.439 0.232,0.139 10 UP 0.584,4.387 1.043,4.539 0.459,0.152 10 DOWN 1.55,4.268 1.153,4.459 false 1.908,4.276 2.426,4.373 false 0.457,1.382 0.679,1.530 0.223,0.147 10 N2 0.696,3.7 1.060,3.847 0.364,0.147 10 N12

Disconnect the N2 master switch connector.


b.

Disconnect the N12 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-4 (UP) - N12-10 (UP) Always Below 1 Ω
N2-5 (DOWN) - N12-7 (DOWN) Always Below 1 Ω
N2-4 (UP) - Body ground Always 10 kΩ or higher
N2-5 (DOWN) - Body ground Always 10 kΩ or higher




OK

7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.
B231475E01
1.326,2.024 0.737,0.897 0.737,0.897 0.968,0.897 false 0.993,0.824 1.733,0.976 0.739,0.152 10 Motor Gear 1.672,2.962 2.352,3.108 0.680,0.145 10 Clockwise 1.946,1.882 3.067,2.028 1.121,0.145 10 Counterclockwise 0.116,0.071 2.592,0.507 2.476,0.437 10 Component without harness connected: (Driver Side Motor)

Remove the driver side motor (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).


b.

Apply positive (+) battery voltage to connector terminal 2 (B).

NOTICE:
·

Do not apply positive (+) battery voltage to any terminals except terminal 2 (B) to avoid damaging the pulse sensor inside the motor.

·

Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.




c.

Apply negative (-) battery voltage to connector terminals 1 (GND) and 7 (DOWN) / 10 (UP).


d.

Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (B)
Battery negative (-): 1 (GND) (3 sec. or more) → 1 (GND) and 10 (UP) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 10 (UP)
Motor gear rotates clockwise
Battery positive (+) → 2 (B)
Battery negative (-): 1 (GND) (3 sec. or more) → 1 (GND) and 7 (DOWN) (within 1 sec.) → 1 (GND) (within 1 sec.) → 1 (GND) and 7 (DOWN)
Motor gear rotates counterclockwise




OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH