Home › Vehicle Interior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234473 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the AUTO UP/DOWN function does not operate, the cause may be one or more of the following:

·

The ECU in the front passenger side motor determines that the front passenger side motor has not been initialized.

·

The power window regulator switch assembly has a malfunction.

·

The Hall-IC in the front passenger side motor has a malfunction.

·

The wiring between the power window regulator switch assembly and the front passenger side motor is open or shorted.


WIRING DIAGRAM

B231468E01
4.682,0.253 4.814,0.405 0.132,0.152 10 4 4.933,0.36 5.339,0.529 0.406,0.170 10 AUTO 1.927,0.368 2.270,0.537 0.343,0.170 10 GND 2.456,0.36 2.875,0.530 0.420,0.170 10 AUTO 1.869,0.977 3.906,1.344 2.037,0.368 10 Power Window Regulator Switch Assembly 4.861,0.987 6.813,1.329 1.952,0.342 10 Front Power Window Regulator Motor Assembly RH 1.697,0.271 1.807,0.427 0.109,0.156 10 1 1.871,0.805 2.182,0.961 0.311,0.156 10 M10 4.869,0.807 5.197,0.963 0.329,0.156 10 M11 2.996,0.261 3.190,0.417 0.194,0.156 10 8

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC B2311 is output B
DTC B2312 is output C
DTC B2313 is output D
LIN communication system DTCs are output E



A

2.CHECK MANUAL UP / DOWN FUNCTION

B

C

D

E

2.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual UP/DOWN function using the power window regulator switch assembly can operate the front passenger side door power window (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>OPERATION CHECK).

OK:

Manual UP/DOWN function operates normally.




OK

3.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)

NG

3.READ VALUE USING TECHSTREAM (FRONT PASSENGER SIDE MOTOR)
a.

Use the Data List to check if the front passenger side motor is functioning properly.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window auto UP/DOWN switch signal / ON or OFF ON: Power window regulator switch assembly operated
OFF: Power window regulator switch assembly not operated
-


OK:

The Techstream display changes when power window regulator switch assembly is operated.



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)
4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT PASSENGER SIDE MOTOR)
a.
U151994E01
0.161,2.274 2.675,2.997 2.514,0.723 10 Front view of wire harness connector: (to Front Passenger Side Motor) 0.208,0.034 2.692,0.738 2.484,0.704 10 Front view of wire harness connector: (to Power Window Regulator Switch Assembly) 0.555,1.328 0.883,1.512 0.327,0.184 10 M10 0.611,3.266 0.967,3.450 0.356,0.184 10 M11 2.402,1.561 2.822,1.723 0.420,0.162 10 AUTO 1.957,1.817 2.376,1.641 false 0.721,3.639 1.141,3.800 0.420,0.162 10 AUTO 1.243,3.71 1.612,3.909 false

Disconnect the M10 switch connector.


b.

Disconnect the M11 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M10-8 (AUTO) - M11-4 (AUTO) Always Below 1 Ω
M10-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

5.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B231347E03
0.026,1.259 2.804,1.614 2.779,0.355 10 Component without harness connected: (Power Window Regulator Switch Assembly) 0.599,3.038 1.005,3.187 0.406,0.149 10 AUTO 2.455,2.433 2.784,2.587 0.330,0.154 10 GND 1.476,2.8 1.097,3.034 false 2.097,2.53 2.438,2.53 false

Remove the power window regulator switch assembly (See page Vehicle Interior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (AUTO) - 1 (GND) AUTO UP/DOWN operation Below 1 Ω
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY