Home › Vehicle Interior › WINDOW / GLASS › BACK WINDOW GLASS(for Regular Cab and Double Cab)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234467 BACK WINDOW GLASS(for Regular Cab and Double Cab) A

WINDOW / GLASS  BACK WINDOW GLASS(for Regular Cab and Double Cab)  INSTALLATION  


PROCEDURE

Hide 64818 1.INSTALL NO. 1 BACK WINDOW GLASS SPACER

B166841

a.

Install 2 new spacers onto the back window assembly as shown in the illustration.


Hide 64819A 2.INSTALL NO. 2 BACK WINDOW GLASS SPACER

B166842

a.

Install 2 new spacers onto the back window assembly as shown in the illustration.


Hide 64810 3.INSTALL BACK WINDOW ASSEMBLY

U151926E02
2.313,2.625 1.26,2.625 false 1.24,0.865 1.844,1.031 0.604,0.167 10 false Primer M 1.271,2.208 1.865,2.385 0.594,0.177 10 false Primer M 0.615,2.542 1.188,2.74 0.573,0.198 10 false Adhesive 1.771,0.313 2.615,0.51 0.844,0.198 10 false CORRECT 1.792,2.781 2.615,2.948 0.823,0.167 10 false INCORRECT

a.

Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Do not apply primer to the adhesive.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Using a brush or sponge, apply Primer G to the contact surface of the back window.

B166488E02
1.573,1.271 1.729,1.438 0.156,0.167 10 false A 1.583,1.625 1.74,1.792 0.156,0.167 10 false A 0.188,1.51 0.302,1.667 0.115,0.156 10 false B 0.781,1.677 0.938,1.844 0.156,0.167 10 false B 3.052,1.594 3.208,1.76 0.156,0.167 10 true B 3.552,1.49 3.708,1.656 0.156,0.167 10 false B 3.583,1.917 3.74,2.083 0.156,0.167 10 false C 0.198,1.927 0.323,2.094 0.125,0.167 10 false C 1.563,2.052 1.719,2.219 0.156,0.167 10 false D 1.563,2.448 1.698,2.615 0.135,0.167 10 false D 0.073,2.365 0.229,2.531 0.156,0.167 10 false C 3.74,2.302 3.896,2.469 0.156,0.167 10 false C 0.729,3.469 1.333,3.646 0.604,0.177 10 false Primer G 3.979,0.365 4.344,0.531 0.365,0.167 10 false A - A 5.594,0.344 5.958,0.51 0.365,0.167 10 false B - B 3.948,2 4.313,2.167 0.365,0.167 10 false C - C 5.573,2 5.938,2.167 0.365,0.167 10 false D - D 0.083,0.104 1.656,0.302 1.573,0.198 10 false Backside for Fixed Type:

B166489E03
1.615,1.177 1.771,1.344 0.156,0.167 10 false A 1.594,1.594 1.75,1.76 0.156,0.167 10 true A 0.25,1.438 0.406,1.604 0.156,0.167 10 false B 0.74,1.594 0.896,1.76 0.156,0.167 10 true B 3.052,1.604 3.208,1.771 0.156,0.167 10 true B 3.552,1.438 3.708,1.604 0.156,0.167 10 false B 3.573,1.906 3.729,2.073 0.156,0.167 10 false C 0.167,1.906 0.302,2.073 0.135,0.167 10 false C 1.594,2.042 1.708,2.219 0.115,0.177 10 false D 1.563,2.458 1.698,2.625 0.135,0.167 10 false D 0.031,2.344 0.177,2.521 0.146,0.177 10 false C 3.729,2.354 3.865,2.521 0.135,0.167 10 false C 0.729,3.448 1.396,3.656 0.667,0.208 10 false Primer G 3.958,0.354 4.323,0.521 0.365,0.167 10 false A - A 5.563,0.344 5.927,0.51 0.365,0.167 10 false B - B 3.948,2.021 4.313,2.188 0.365,0.167 10 false C - C 5.573,2.031 5.938,2.198 0.365,0.167 10 false D - D 0.083,0.104 2.969,0.344 2.885,0.24 10 false Backside for Slide Type, for Power Slide Type:

HINT:

If primer is applied to an area that is not specified, wipe off the primer with a non-residue solvent before it dries.


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




c.

Apply adhesive to the back window.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of the cartridge nozzle as shown in the illustration below.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage time frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the back window as shown in the illustration.

B166490E01
2.363,1.612 3.128,1.796 0.765,0.184 10 Adhesive 3.109,1.339 3.331,1.561 0.222,0.222 10 a 0.865,1.601 1.087,1.823 0.222,0.222 10 a 2.572,0.832 2.794,1.054 0.222,0.222 10 b 1.332,1.817 1.554,2.038 0.222,0.222 10 b 1.58,2.142 1.736,2.311 0.156,0.170 10 A 1.584,2.526 1.740,2.695 0.156,0.170 10 A 0.23,2.373 0.386,2.543 0.156,0.170 10 B 0.736,2.571 0.892,2.740 0.156,0.170 10 B 3.057,2.621 3.213,2.791 0.156,0.170 10 B 3.568,2.421 3.724,2.590 0.156,0.170 10 B 3.594,2.838 3.750,3.008 0.156,0.170 10 C 0.193,2.837 0.349,3.006 0.156,0.170 10 C 1.576,2.925 1.732,3.095 0.156,0.170 10 D 1.572,3.36 1.728,3.530 0.156,0.170 10 D 0.082,3.278 0.238,3.448 0.156,0.170 10 C 3.725,3.269 3.880,3.438 0.156,0.170 10 C 3.931,0.295 4.296,0.457 0.364,0.163 10 A - A 5.58,0.295 5.945,0.457 0.364,0.163 10 B - B 3.92,1.943 4.284,2.105 0.364,0.163 10 C - C 5.559,1.943 5.924,2.105 0.364,0.163 10 D - D 0.036,0 1.953,0.200 1.917,0.200 10 Backside for Fixed Type:

B166491E02
2.375,1.601 3.139,1.784 0.765,0.184 10 Adhesive 3.12,1.328 3.342,1.550 0.222,0.222 10 a 0.876,1.589 1.098,1.811 0.222,0.222 10 a 2.583,0.821 2.805,1.043 0.222,0.222 10 b 1.343,1.805 1.565,2.027 0.222,0.222 10 b 1.591,2.13 1.747,2.300 0.156,0.170 10 A 1.6,2.545 1.756,2.714 0.156,0.170 10 A 0.241,2.362 0.397,2.532 0.156,0.170 10 B 0.748,2.559 0.904,2.729 0.156,0.170 10 B 3.068,2.61 3.224,2.779 0.156,0.170 10 B 3.579,2.409 3.735,2.579 0.156,0.170 10 B 3.605,2.826 3.761,2.996 0.156,0.170 10 C 0.204,2.825 0.360,2.995 0.156,0.170 10 C 1.587,2.914 1.743,3.084 0.156,0.170 10 D 1.584,3.348 1.740,3.518 0.156,0.170 10 D 0.094,3.267 0.249,3.436 0.156,0.170 10 C 3.736,3.257 3.892,3.427 0.156,0.170 10 C 3.943,0.283 4.307,0.446 0.364,0.163 10 A - A 5.592,0.283 5.956,0.446 0.364,0.163 10 B - B 3.932,1.931 4.296,2.094 0.364,0.163 10 C - C 5.571,1.931 5.935,2.094 0.364,0.163 10 D - D 0.035,0 2.997,0.216 2.961,0.216 10 Backside for Slide Type, for Power Slide Type:

Standard:
Area Specified Condition
a 12.0 mm (0.472 in.)
b 8.0 mm (0.315 in.)




d.
B166485

B166484E02
1.667,0.823 1.156,0.823 1.156,0.823 1.156,1.479 false 1.677,1.083 1.146,1.083 false 0.729,1.49 1.615,1.823 0.885,0.333 10 true Matchmark

Using suction cups, position the glass so that the reference marks are aligned. Press it in gently along the rim.

NOTICE:
·

Allow the primer coating to dry for 3 minutes or more.

·

Check that the clips are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and glass.




e.

Lightly press the front surface of the back window to ensure that the back window is securely fit to the vehicle body.

NOTICE:

Check that the spacers are attached to the vehicle body correctly.



f.

Using a scraper, remove any excess or protruding adhesive.

NOTICE:

Do not drive the vehicle within the time written in the table below.


Minimum time:
Temperature Minimum time prior to driving vehicle
35°C (95°F) 1 hour 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours



Hide 64810 4.CHECK FOR LEAK AND REPAIR

a.

Conduct a leak test after the adhesive has completely hardened.


b.

Seal any leaks with auto glass sealer.


Hide 75571G 5.INSTALL UPPER OUTSIDE BACK WINDOW MOULDING (for Slide Type, for Power Slide Type)

B166492E01
1.536,0.407 2.951,0.625 1.415,0.218 10 Double-sided Tape 1.484,0.487 1.249,0.487 1.249,0.487 1.249,0.986 false

a.

Clean the back window surface.

i.

Using a heat light, heat the back window surface.


ii.

Remove the double-sided tape from the back window.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

If reusing the moulding:

Clean the moulding.

i.

Using a heat light, heat the moulding.


ii.

Remove the double-sided tape from the moulding.


iii.

Wipe off any tape adhesive residue with cleaner.


iv.

Apply new double-sided tape to the moulding, as shown in the illustration.



c.

Install the moulding.

i.

Using a heat light, heat the back window and moulding.


ii.

Remove the peeling paper.


iii.

Attach the 3 clips to install the moulding.



Hide 75575E 6.INSTALL LOWER OUTSIDE BACK WINDOW MOULDING (for Slide Type, for Power Slide Type)

B166493E03
1.396,1.135 1.396,1.552 false 0.844,1.583 2.052,1.771 1.208,0.188 10 false Double-sided Tape

a.

Clean the back window surface.

i.

Using a heat light, heat the back window surface.


ii.

Remove the double-sided tape from the back window.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

If reusing the moulding:

Clean the moulding.

i.

Using a heat light, heat the moulding.


ii.

Remove the double-sided tape from the moulding.


iii.

Wipe off any tape adhesive residue with cleaner.


iv.

Apply new double-sided tape to the moulding, as shown in the illustration.



c.

Install the moulding.

i.

Using a heat light, heat the back window and moulding.


ii.

Remove the peeling paper.


iii.

Attach the 3 clips to install the moulding.



Hide 75554A 7.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH

Hide 75553A 8.INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:

Use the same procedures described for the LH side.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

a.

for Regular Cab:

Install the roof headlining (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>INSTALLATION).


b.

for Double Cab:

Install the roof headlining (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION).


Hide 69957 10.INSTALL BACK DOOR GLASS CHANNEL (for Power Slide Type)

HINT:

Perform these procedures only when replacing the back window glass.


a.

Using a brush or sponge, coat the application area of a new back window glass with Primer G.

B231502E01
0.602,1.53 1.189,1.667 0.586,0.137 10 Primer G 2.618,1.188 2.737,1.327 0.119,0.139 10 A 2.618,1.544 2.742,1.686 0.123,0.141 10 A 4.327,0.189 4.715,0.385 0.388,0.196 10 A - A 4.525,1.244 4.700,1.451 0.175,0.207 10 a

Standard:
Area Specified Condition
a 10.0 mm (0.394 in.)


NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



b.
B231503

Using a brush or sponge, coat the application area of a new back door glass channel with Primer M.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



c.

Apply adhesive to the back door glass channel.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.

Cut off the tip of a cartridge nozzle.

HINT:

After cutting off the tip, use all adhesive within the time written in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour 40 minutes
5°C (41°F) 8 hours



ii.
B231504

Load a sealer gun with the cartridge.


iii.

Apply adhesive to the back door glass channel as shown in the illustration.



d.

Install the back door glass as shown in the illustration.

B442902E01
2.563,1.229 2.688,1.406 0.125,0.177 10 false A 2.552,1.552 2.677,1.729 0.125,0.177 10 false A 4.365,0.177 4.708,0.354 0.344,0.177 10 false A - A 3.875,0.958 4.458,1.135 0.583,0.177 10 false Backside


e.
B231506

Apply non-residue solvent to a clean cloth and wipe off any excess or protruding adhesive.


Hide 64811 11.INSTALL BACK WINDOW GLASS WITH BACK DOOR GLASS CHANNEL (for Power Slide Type)

HINT:

Perform these procedures only when replacing the back window glass.


a.

Insert the back window glass into the channel (arrow 1). Attach the upper part of the back window glass to the upper channel (arrow 2). Then slide the back window glass towards the RH side (arrow 3) so that the glass channel fits between the ribs to install the back window glass.


b.

Insert the seal into the bottom of the channel (arrow 4), and then slightly push the seal to the channel (arrow 5) to install it.


c.

Using a T10 "TORX" driver, install the stopper with the screw (illustration A).

B231499E02
2.021,4.104 1.771,4.25 1.771,4.25 1.771,4.521 false 5.719,5.802 5.583,5.667 5.583,5.667 5.49,5.667 false 4.438,4.698 3.813,5.917 3.813,5.917 3.385,5.917 false 5.927,5.396 6.083,5.552 0.156,0.156 10 false A 6.927,3.135 7.052,3.292 0.125,0.156 10 false 4 6.583,3.49 6.719,3.667 0.135,0.177 10 false 5 5.552,2.844 5.698,3.031 0.146,0.188 10 false 1 5.896,2.292 6.031,2.49 0.135,0.198 10 false 2 4.875,2.302 5.042,2.521 0.167,0.219 10 false 3 4.271,2.219 4.385,2.448 0.115,0.229 10 true B 4.271,2.927 4.385,3.104 0.115,0.177 10 false B 0.792,4.875 1.188,5.083 0.396,0.208 10 false B - B 1.667,4.542 2.271,4.771 0.604,0.229 10 false Seal 4.969,5.583 5.521,5.781 0.552,0.198 10 false Stopper 1.76,5.771 3.458,6.146 1.698,0.375 10 false Back Window Glass with Back Door Glass Channel


Hide 85710J 12.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Power Slide Type)

B227089

a.

Using a T25 "TORX" socket, install the power window regulator motor to the base plate with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 69811D 13.INSTALL DOOR WINDOW REGULATOR BASE PLATE (for Power Slide Type)

B227087E02
0.729,0.573 0.854,0.771 0.125,0.198 10 false 1 0.813,1.927 0.979,2.094 0.167,0.167 10 false 3 3.177,0.573 3.323,0.74 0.146,0.167 10 false 2

a.

Install the door window regulator base plate with the 3 nuts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 69088A 14.INSTALL DOOR WINDOW REGULATOR CABLE SUB-ASSEMBLY (for Power Slide Type)

B227108E02
1.958,1.438 1.958,0.406 1.958,0.406 1.76,0.406 false 1.448,1.49 0.885,2.479 false 2.531,2.021 2.74,2.021 2.74,2.021 2.74,2.667 false 0.458,2.49 1.073,2.708 0.615,0.219 10 false Pivot Pin 0.646,0.323 1.74,0.531 1.094,0.208 10 false Counterclockwise 2.094,2.677 3.135,2.885 1.042,0.208 10 false Drum Assembly

a.

Rotate the drum assembly counterclockwise to align it with the motor pivot pin, and then connect the motor drum assembly to the motor pivot pin.

NOTICE:

Do not rotate the drum assembly more than 45°.



b.
U152008E02
1.396,0.51 1.802,0.198 1.802,0.198 2.031,0.198 false 1.302,1.167 1.01,0.948 1.01,0.948 0.885,0.948 false 2.042,0.135 2.719,0.323 0.677,0.188 10 false Datum Pin 0.208,0.854 0.885,1.042 0.677,0.188 10 false Clockwise 3.115,1.813 3.313,2.021 0.198,0.208 10 false 1 2.125,2.552 2.25,2.719 0.125,0.167 10 false 2

Rotate the drum assembly clockwise to attach the claw and connect the datum pin.


c.

Install the 2 bolts in the order shown in the illustration.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.

Insert the wires into the back window as shown in the illustration labeled A.

B227086E08
1.458,4.385 2.042,5.313 2.042,5.313 2.25,4.583 false 2.052,5.302 2.906,4.563 false 4.917,4.573 5.26,5.375 5.26,5.375 6.26,4.417 false 5.365,4.563 5.26,5.365 false 4.875,0.802 4.969,0.802 4.969,0.802 5.313,1.948 false 3.49,1.792 4.083,0.802 4.083,0.802 4.135,0.802 false 1.781,5.771 2.021,6.01 0.24,0.24 10 false A 5.292,5.771 5.531,6.01 0.24,0.24 10 false A 3.396,0.969 3.542,1.156 0.146,0.188 10 false B 5.573,1.052 5.708,1.24 0.135,0.188 10 false B 1.99,5.313 2.177,5.479 0.188,0.167 10 false C 5.24,5.406 5.385,5.552 0.146,0.146 10 false C 4.24,0.635 5.052,0.823 0.813,0.188 10 false Wire End


e.

Compress the springs to release the tension in the cables, connect the wire ends to the back window as shown in the illustration labeled B, Then release the springs to restore the tension.

NOTICE:
B231500

Insert the cables so that the caps are fully inserted into the stoppers as shown in the illustration.


HINT:

Use the same procedure described for the LH side.



f.

Attach the 6 clips labeled C in the illustration.


Hide 64141H 15.INSTALL NO. 1 BACK PANEL SILENCER (for Power Slide Type)

B227085

a.

Install the No. 1 back panel silencer with the 4 clips.


Hide 81240 17.INSTALL NO. 1 ROOM LIGHT ASSEMBLY

Hide 62520P 18.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

a.

for Regular Cab:

Install the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>INSTALLATION).


b.

for Double Cab:

Install the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION).


Hide 62510P 19.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 62540 20.INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH

a.

for Regular Cab:

Install the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Regular Cab)>INSTALLATION).


b.

for Double Cab:

Install the quarter trim panel (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for Double Cab)>INSTALLATION).


Hide 62530 21.INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 64429E 22.INSTALL LUGGAGE COMPARTMENT BOX RH (for Regular Cab)

Hide 64439D 23.INSTALL LUGGAGE COMPARTMENT BOX LH (for Regular Cab)

Hide 64261C 24.INSTALL UPPER BACK PANEL GARNISH (for Regular Cab)

Hide 62312B 25.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab)

Hide 62311B 26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab)

Hide 62332A 27.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab)

Hide 62331A 28.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab)

Hide 67914 29.INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab)

Hide 67913 30.INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab)

Hide 67918B 31.INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab)

Hide 67917B 32.INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab)

Hide 33.INSTALL REAR SEAT ASSEMBLY (for Double Cab)

Hide 34.INSTALL FRONT SEAT ASSEMBLY (for Center Seat)

Hide 35.INSTALL FRONT SEAT ASSEMBLY (for Power Seat)

Hide 36.INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)