Home › Power Source / Network › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049167 MULTIPLEX COMMUNICATION _0234509 LIN COMMUNICATION SYSTEM C

MULTIPLEX COMMUNICATION  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is output when LIN communication between the front power window regulator motor assembly LH and main body ECU (driver side junction block) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2321 No communication between the front power window regulator motor assembly LH and main body ECU (driver side junction block) for 10 seconds or more.
·

Front power window regulator motor assembly LH

·

Main body ECU (driver side junction block)

·

Harness or connector



WIRING DIAGRAM

B356225E01
5.071,1.279 5.381,1.460 0.310,0.181 10 LIN2 4.752,1.878 4.947,2.060 0.195,0.181 10 J2 4.752,2.017 6.546,2.400 1.794,0.383 10 Main Body ECU (Driver Side Junction Block) 4.789,1.173 4.961,1.354 0.171,0.181 10 10 2.521,1.279 2.831,1.460 0.310,0.181 10 LIN1 1.861,1.279 2.172,1.460 0.310,0.181 10 LIN2 1.771,1.879 1.981,2.060 0.210,0.181 10 N2 2.946,1.159 3.102,1.340 0.156,0.181 10 6 1.613,1.159 1.768,1.340 0.156,0.181 10 7 3.589,3.12 3.822,3.301 0.233,0.181 10 LIN 4.262,3.12 4.588,3.301 0.326,0.181 10 GND 3.354,3.014 3.510,3.195 0.156,0.181 10 9 3.566,3.864 3.721,4.046 0.156,0.181 10 B 3.51,4.292 3.809,4.473 0.299,0.181 10 N12 3.354,3.758 3.510,3.940 0.156,0.181 10 2 0.609,3.854 1.382,4.035 0.773,0.181 10 from Battery 1.614,4.031 2.589,4.212 0.974,0.181 10 POWER No.3 0.953,4.693 2.699,4.874 1.746,0.181 10 : LIN Communication Line 4.677,3.014 4.833,3.195 0.156,0.181 10 1 1.772,2.05 3.525,2.395 1.753,0.345 10 Power Window Regulator Master Switch Assembly 3.51,4.469 5.547,4.825 2.037,0.356 10 Front Power Window Regulator Motor Assembly LH

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch OFF to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:
·

DTC B2325 is output when communication between the front power window regulator motor assembly LH and main body ECU (driver side junction block) stops.

·

When DTC B1206 and B2321 are output simultaneously, perform the troubleshooting for DTC B1206 first (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>B1206).



PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2321 output reoccurs A
DTC B2321 output does not reoccur B



A

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REGULATOR MOTOR LH)

B

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REGULATOR MOTOR LH)
a.
U152789E02
2.24,1.719 2.594,1.917 false 2.021,4.313 2.333,4.458 false 1.01,1.479 1.208,1.656 0.198,0.177 10 false J2 1.188,3.958 1.469,4.135 0.281,0.177 10 false N12 0.104,0.01 2.469,0.406 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 0.104,2.146 2.667,2.667 2.563,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 2.646,1.854 2.958,2.031 0.313,0.177 10 false LIN2 2.375,4.385 2.604,4.563 0.229,0.177 10 false LIN

Disconnect the J2 main body ECU (driver side junction block) connector.


b.

Disconnect the N12 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-10 (LIN2) - N12-9 (LIN) Always Below 1 Ω
J2-10 (LIN2) or N12-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REGULATOR MOTOR LH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (REGULATOR MOTOR LH - BATTERY AND BODY GROUND)
a.
U152791E02
2.063,2.219 2.333,2.042 false 1.708,2.219 1.396,1.979 false 1.094,2.396 1.385,2.573 0.292,0.177 10 false N12 0.083,0.052 2.427,0.573 2.344,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 2.375,1.927 2.531,2.104 0.156,0.177 10 false B 1.073,1.865 1.396,2.042 0.323,0.177 10 false GND

Disconnect the N12 front power window regulator motor assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
N12-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
N12-2 (B) - Body ground Always 11 to 14 V




OK

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Temporarily replace the front power window regulator motor assembly LH with a new or normally functioning one (See page Vehicle Interior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).




NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2321 output does not reoccur A
DTC B2321 output reoccurs B



A

END (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)